User Manual FLUKE 9103-A-156 Field Dry-Well Insert A, miscellaneous, cold side

Documents for FLUKE 9103-A-156

User Manual for the Fluke 9103-A-156 Field Dry-Well Insert A, miscellaneous, cold side

For 9103-A-156.

• Model 9103 Dry-Well1
  • Warranty2
  • Table of Contents3
  • Figures6
  • Tables7
• 1 Before You Start9
  • 1.1 Symbols Used9
  • 1.2 Safety Information10
    • 1.2.1 Warnings10
    • 1.2.2 Cautions11
  • 1.3 Authorized Service Centers11
• 2 Introduction15
• 3 Specifications and EnvironmentalConditions17
  • 3.1 Specifications17
  • 3.2 Environmental Conditions17
• 4 Quick Start19
  • 4.1 Unpacking19
  • 4.2 Setup19
  • 4.3 Power19
  • 4.4 Setting the Temperature20
• 5 Parts and Controls21
  • 5.1 Back Panel21
  • 5.2 Front Panel21
  • 5.3 Constant Temperature Block Assembly23
  • 5.4 Probe Sleeves23
• 6 General25
  • 6.1 Changing Display Units25
  • 6.2 Thermal Electric Devices (TED)25
• 7 Controller Operation27
  • 7.1 Well Temperature27
  • 7.2 Temperature Set-point27
    • 7.2.1 Programmable Set-points27
    • 7.2.2 Set-point Value29
    • 7.2.3 Temperature Scale Units29
  • 7.3 Scan30
    • 7.3.1 Scan Control30
    • 7.3.2 Scan Rate30
  • 7.4 Temperature Display Hold30
    • 7.4.1 Enabling the Hold Temperature Display31
    • 7.4.2 Mode Setting31
    • 7.4.3 Switch Wiring31
    • 7.4.4 Switch Test Example32
  • 7.5 Set-point Resistance32
  • 7.6 Temperature Scale Units32
  • 7.7 Secondary Menu32
  • 7.8 Thermal Electric Devices (TED)33
  • 7.9 Proportional Band33
  • 7.10 Controller Configuration34
  • 7.11 Operating Parameters34
  • 7.12 Serial Interface Parameters35
    • 7.12.1 BAUD Rate35
    • 7.12.2 Sample Period36
    • 7.12.3 Duplex Mode36
    • 7.12.4 Linefeed36
  • 7.13 Calibration Parameters37
    • 7.13.1 R037
    • 7.13.2 ALPHA37
    • 7.13.3 DELTA38
    • 7.13.4 BETA38
• 8 Digital Communication Interface39
  • 8.1 Serial Communications39
    • 8.1.1 Wiring39
    • 8.1.2 Setup39
      • 8.1.2.1 BAUD Rate40
      • 8.1.2.2 Sample Period40
      • 8.1.2.3 Duplex Mode40
      • 8.1.2.4 Linefeed40
    • 8.1.3 Serial Operation41
  • 8.2 Interface Commands41
• 9 Test Probe Calibration45
  • 9.1 Calibrating a Single Probe45
  • 9.2 Stabilization and Accuracy45
• 10 Calibration Procedure47
  • 10.1 Calibration Points47
  • 10.2 Calibration Procedure47
    • 10.2.1 Compute DELTA47
    • 10.2.2 Compute R0 and ALPHA48
    • 10.2.3 Compute BETA49
    • 10.2.4 Accuracy and Repeatability49
• 11 Maintenance51
• 12 Trouble Shooting53
  • 12.1 Troubleshooting53
  • 12.2 CE Comments54
    • 12.2.1 EMC Directive54
    • 12.2.2 Low Voltage Directive (Safety)54