Instruction Manual
Item: 12211
Model: 32510380
12 Inch
Table Fan
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
WA R R A N T Y I NF O R M AT I O N
Printed In China
©
2023 Sunbeam Products, Inc. All rights reserved.
HOLMES
®
is a registered trademark of Sunbeam Products, Inc. used under license.
Distributed by Star Elite Inc., Montreal, Canada H3B 3X9
SEH024-090623
M A I N T E N A N C E
USER SERVICING INSTRUCTIONS
Follow these instructions to safely and correctly care for this fan.
REPLACEABLE FUSE
If the (2.5 Amp, 125 Volt) replaceable fuse blows, please visit our website at www.getholmesfans.com for information
on how to order a new fuse. Follow the below instructions to replace the fuse on the plug.
REPLACING THE FUSE
1. Unplug the fan.
Grasp plug and remove from the receptacle or other outlet device.
NOTE: Do not unplug by pulling on cord.
2. Open fuse cover, located on the top of the plug, by using your thumb or a flathead
screwdriver to slide the cover towards the prongs.
NOTE: Ensure the fuse cover is completely open before attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver to pry it from the compartment at
the metal ends of the fuse. (See Figure 2)
4. Place plug on a solid, flat surface. Insert new 2.5 Amp, 125 Volt fuse into fuse
compartment. Use a small screwdriver to secure the metal ends of the fuse into the
compartment.
CAUTION: Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
5. Slide fuse cover closed completely.
NOTE: If fuse cover is difficult to close, make sure the fuse is completely secured in place by pressing on metal ends
of the fuse.
CAUTION: Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be
removed. Discard product if the attachment plug is damaged.
Figure 2
Fuse
Fuse cover
Metal ends
3 YEAR LIMITED WARRANTY
This device has a limited warranty of 3 years from the original date of purchase against workmanship and defects in
material. If under normal use, your product fails to operate, please contact our customer service department at
info@getholmesfans.com. A refund or replacement will be provided to you with proof of purchase. Star Elite Inc. may
deny claims of damage caused by misuse or modifications of this product.
Warranty Service
Contact our customer service at www.getholmesfans.com/en/contact-us
or info@getholmesfans.com or 1-866-769-3166 (8:30 am - 5:00 pm EST) Monday-Friday.
Our team will be happy to assist.
www.getholmesfans.com
IMPORTANT SAFETY INSTRUCTIONS
A S S E M B LY / O P E R AT I O N C L E A N I N G / M A IN T E N A N C E
FAN CLEANING
• Always unplug the fan before cleaning.
• Do not allow water to drip on or into the fan
housing.
• Use only a soft cloth moistened with a mild soap
solution.
• Do not use harsh chemicals such as gasoline,
thinner or benzene as a cleaner.
• Do not attempt to remove the fan blade.
• Please use caution around the housing area.
Do not allow the motor or other electrical
components to be exposed to water.
FAN HEAD AND BASE CLEANING
Unplug the fan, then, using a soft, moist cloth, with or
without a mild soap solution, carefully clean the fan base
and head. Use CAUTION around the housing area.
Do not allow the motor or other electrical components to
be exposed to water.
FAN STORAGE
• Store the fan in a clean, dry location between seasons
or when not in use for an extended period.
• Keep the fan protected from dirt and dust during
storage.
TILT ADJUSTMENT
To change the tilting angle of the fan head, simply move
the fan head to manually position to the desired angle.
An audible click will confirm each angle adjustment.
OPERATING INSTRUCTIONS
1. Set fan base on a dry, level, stable surface.
2. Plug cord into any standard 120 volt AC outlet.
3. The speed is adjusted by pressing the speed control
buttons to the desired setting:
O-OFF
1-Low
2-Medium
3-High
4. To start oscillation, press the Oscillation Knob (H) down.
To stop oscillation, pull the Oscillation Knob (H) up.
FIGURE 1
A
B
C
D
E
F
G
H
J
I
K
L
A. Front Grill
B. Blade Cap
C. Fan Blade
D. Rear Grill Mounting Nut
E. Rear Grill
F. Motor Shaft
G. Motor Housing
H. Oscillation Knob
I. Fan Pole
J. Control Panel
K. Fan Base
L. Power Cord
13. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
14. Do not use outdoors.
15. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
16. Always use on a dry, level surface.
17. Do not operate fan until fully assembled with all parts
properly in place.
18. This product is intended for household use ONLY and
not for commercial or industrial applications.
19. WARNING: To reduce the risk of electrical shock and
injury to persons, do not use in window.
20. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
21. WARNING: To reduce the risk of fire, electric shock
or injury to persons, do not use replacement parts that
have not been recommended by the manufacturer
(e.g. parts made at home using a 3D Printer).
22. This fan employs overload protection (fuse). A blown
fuse indicates an overload or short-circuit situation.
If the fuse blows, unplug the product from the outlet.
Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a
short circuit may be present and the product should be
discarded or contact customer service.
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse unit,
plug or cord in water or spray with liquids and plug
the appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
used near children.
5. Not intended for use by children.
6. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on or
taking off parts and before cleaning.
7. Avoid contact with moving parts.
8. Do not operate in the presence of explosive and/or
flammable fumes.
9. To avoid fire hazard, NEVER place the cord under rugs
or any parts near an open flame, cooking or other
heating appliance.
10. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
contact customer service.
11. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped
over.
12. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than
the other). To reduce the risk of electric shock, this plug is intended to
fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
For inquiries regarding recycling and proper disposal
of this product, please contact your local waste
management facility.
ASSEMBLY INSTRUCTIONS (SEE FIGURE 1)
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE
PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
PARTS THAT COULD BE REQUIRED TO OPERATE THIS FAN.
Estimated assembly time: 5–10 minutes
1. Pull power cord (L) through base opening (K) and
secure into notch at the back of the base.
2. To assemble the base, insert the Control Panel (J)
and Power Cord (L) into the Fan Base (K).
3. Line up the center hole of the Rear Grill (E) with the
Motor Shaft (F) on the Motor Housing (G).
4. Secure Rear Grill (E) to Motor Housing (G) with Rear
Grill Mounting Nut (D). Turn clockwise to tighten.
5. Secure Fan Blade (C) to Motor Shaft (F) with the
Blade Cap (B). Align blade notches and push into
the Motor Shaft (F) cross pin. Turn counterclockwise
to tighten.
6. Align the Front Grill (A) with the Rear Grill (E) so
the logo is in the centre. Secure in place by lightly
pushing together, an audible click will confirm
alignment.
IMPORTANT SAFETY INSTRUCTIONS
A S S E M B LY / O P E R AT I O N C L E A N I N G / M A IN T E N A N C E
FAN CLEANING
• Always unplug the fan before cleaning.
• Do not allow water to drip on or into the fan
housing.
• Use only a soft cloth moistened with a mild soap
solution.
• Do not use harsh chemicals such as gasoline,
thinner or benzene as a cleaner.
• Do not attempt to remove the fan blade.
• Please use caution around the housing area.
Do not allow the motor or other electrical
components to be exposed to water.
FAN HEAD AND BASE CLEANING
Unplug the fan, then, using a soft, moist cloth, with or
without a mild soap solution, carefully clean the fan base
and head. Use CAUTION around the housing area.
Do not allow the motor or other electrical components to
be exposed to water.
FAN STORAGE
• Store the fan in a clean, dry location between seasons
or when not in use for an extended period.
• Keep the fan protected from dirt and dust during
storage.
TILT ADJUSTMENT
To change the tilting angle of the fan head, simply move
the fan head to manually position to the desired angle.
An audible click will confirm each angle adjustment.
OPERATING INSTRUCTIONS
1. Set fan base on a dry, level, stable surface.
2. Plug cord into any standard 120 volt AC outlet.
3. The speed is adjusted by pressing the speed control
buttons to the desired setting:
O-OFF
1-Low
2-Medium
3-High
4. To start oscillation, press the Oscillation Knob (H) down.
To stop oscillation, pull the Oscillation Knob (H) up.
FIGURE 1
A
B
C
D
E
F
G
H
J
I
K
L
A. Front Grill
B. Blade Cap
C. Fan Blade
D. Rear Grill Mounting Nut
E. Rear Grill
F. Motor Shaft
G. Motor Housing
H. Oscillation Knob
I. Fan Pole
J. Control Panel
K. Fan Base
L. Power Cord
13. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
14. Do not use outdoors.
15. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
16. Always use on a dry, level surface.
17. Do not operate fan until fully assembled with all parts
properly in place.
18. This product is intended for household use ONLY and
not for commercial or industrial applications.
19. WARNING: To reduce the risk of electrical shock and
injury to persons, do not use in window.
20. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
21. WARNING: To reduce the risk of fire, electric shock
or injury to persons, do not use replacement parts that
have not been recommended by the manufacturer
(e.g. parts made at home using a 3D Printer).
22. This fan employs overload protection (fuse). A blown
fuse indicates an overload or short-circuit situation.
If the fuse blows, unplug the product from the outlet.
Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a
short circuit may be present and the product should be
discarded or contact customer service.
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse unit,
plug or cord in water or spray with liquids and plug
the appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
used near children.
5. Not intended for use by children.
6. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on or
taking off parts and before cleaning.
7. Avoid contact with moving parts.
8. Do not operate in the presence of explosive and/or
flammable fumes.
9. To avoid fire hazard, NEVER place the cord under rugs
or any parts near an open flame, cooking or other
heating appliance.
10. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
contact customer service.
11. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped
over.
12. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than
the other). To reduce the risk of electric shock, this plug is intended to
fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
For inquiries regarding recycling and proper disposal
of this product, please contact your local waste
management facility.
ASSEMBLY INSTRUCTIONS (SEE FIGURE 1)
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE
PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
PARTS THAT COULD BE REQUIRED TO OPERATE THIS FAN.
Estimated assembly time: 5–10 minutes
1. Pull power cord (L) through base opening (K) and
secure into notch at the back of the base.
2. To assemble the base, insert the Control Panel (J)
and Power Cord (L) into the Fan Base (K).
3. Line up the center hole of the Rear Grill (E) with the
Motor Shaft (F) on the Motor Housing (G).
4. Secure Rear Grill (E) to Motor Housing (G) with Rear
Grill Mounting Nut (D). Turn clockwise to tighten.
5. Secure Fan Blade (C) to Motor Shaft (F) with the
Blade Cap (B). Align blade notches and push into
the Motor Shaft (F) cross pin. Turn counterclockwise
to tighten.
6. Align the Front Grill (A) with the Rear Grill (E) so
the logo is in the centre. Secure in place by lightly
pushing together, an audible click will confirm
alignment.
IMPORTANT SAFETY INSTRUCTIONS
A S S E M B LY / O P E R AT I O N C L E A N I N G / M A IN T E N A N C E
FAN CLEANING
• Always unplug the fan before cleaning.
• Do not allow water to drip on or into the fan
housing.
• Use only a soft cloth moistened with a mild soap
solution.
• Do not use harsh chemicals such as gasoline,
thinner or benzene as a cleaner.
• Do not attempt to remove the fan blade.
• Please use caution around the housing area.
Do not allow the motor or other electrical
components to be exposed to water.
FAN HEAD AND BASE CLEANING
Unplug the fan, then, using a soft, moist cloth, with or
without a mild soap solution, carefully clean the fan base
and head. Use CAUTION around the housing area.
Do not allow the motor or other electrical components to
be exposed to water.
FAN STORAGE
• Store the fan in a clean, dry location between seasons
or when not in use for an extended period.
• Keep the fan protected from dirt and dust during
storage.
TILT ADJUSTMENT
To change the tilting angle of the fan head, simply move
the fan head to manually position to the desired angle.
An audible click will confirm each angle adjustment.
OPERATING INSTRUCTIONS
1. Set fan base on a dry, level, stable surface.
2. Plug cord into any standard 120 volt AC outlet.
3. The speed is adjusted by pressing the speed control
buttons to the desired setting:
O-OFF
1-Low
2-Medium
3-High
4. To start oscillation, press the Oscillation Knob (H) down.
To stop oscillation, pull the Oscillation Knob (H) up.
FIGURE 1
A
B
C
D
E
F
G
H
J
I
K
L
A. Front Grill
B. Blade Cap
C. Fan Blade
D. Rear Grill Mounting Nut
E. Rear Grill
F. Motor Shaft
G. Motor Housing
H. Oscillation Knob
I. Fan Pole
J. Control Panel
K. Fan Base
L. Power Cord
13. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
14. Do not use outdoors.
15. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
16. Always use on a dry, level surface.
17. Do not operate fan until fully assembled with all parts
properly in place.
18. This product is intended for household use ONLY and
not for commercial or industrial applications.
19. WARNING: To reduce the risk of electrical shock and
injury to persons, do not use in window.
20. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
21. WARNING: To reduce the risk of fire, electric shock
or injury to persons, do not use replacement parts that
have not been recommended by the manufacturer
(e.g. parts made at home using a 3D Printer).
22. This fan employs overload protection (fuse). A blown
fuse indicates an overload or short-circuit situation.
If the fuse blows, unplug the product from the outlet.
Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a
short circuit may be present and the product should be
discarded or contact customer service.
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse unit,
plug or cord in water or spray with liquids and plug
the appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
used near children.
5. Not intended for use by children.
6. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on or
taking off parts and before cleaning.
7. Avoid contact with moving parts.
8. Do not operate in the presence of explosive and/or
flammable fumes.
9. To avoid fire hazard, NEVER place the cord under rugs
or any parts near an open flame, cooking or other
heating appliance.
10. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
contact customer service.
11. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped
over.
12. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than
the other). To reduce the risk of electric shock, this plug is intended to
fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
For inquiries regarding recycling and proper disposal
of this product, please contact your local waste
management facility.
ASSEMBLY INSTRUCTIONS (SEE FIGURE 1)
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS OF THE
PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR
PARTS THAT COULD BE REQUIRED TO OPERATE THIS FAN.
Estimated assembly time: 5–10 minutes
1. Pull power cord (L) through base opening (K) and
secure into notch at the back of the base.
2. To assemble the base, insert the Control Panel (J)
and Power Cord (L) into the Fan Base (K).
3. Line up the center hole of the Rear Grill (E) with the
Motor Shaft (F) on the Motor Housing (G).
4. Secure Rear Grill (E) to Motor Housing (G) with Rear
Grill Mounting Nut (D). Turn clockwise to tighten.
5. Secure Fan Blade (C) to Motor Shaft (F) with the
Blade Cap (B). Align blade notches and push into
the Motor Shaft (F) cross pin. Turn counterclockwise
to tighten.
6. Align the Front Grill (A) with the Rear Grill (E) so
the logo is in the centre. Secure in place by lightly
pushing together, an audible click will confirm
alignment.
Instruction Manual
Item: 12211
Model: 32510380
12 Inch
Table Fan
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
WA R R A N T Y I N F O R M AT I O N
Printed In China
©
2023 Sunbeam Products, Inc. All rights reserved.
HOLMES
®
is a registered trademark of Sunbeam Products, Inc. used under license.
Distributed by Star Elite Inc., Montreal, Canada H3B 3X9
SEH024-090623
M A I N T E N A N C E
USER SERVICING INSTRUCTIONS
Follow these instructions to safely and correctly care for this fan.
REPLACEABLE FUSE
If the (2.5 Amp, 125 Volt) replaceable fuse blows, please visit our website at www.getholmesfans.com for information
on how to order a new fuse. Follow the below instructions to replace the fuse on the plug.
REPLACING THE FUSE
1. Unplug the fan.
Grasp plug and remove from the receptacle or other outlet device.
NOTE: Do not unplug by pulling on cord.
2. Open fuse cover, located on the top of the plug, by using your thumb or a flathead
screwdriver to slide the cover towards the prongs.
NOTE: Ensure the fuse cover is completely open before attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver to pry it from the compartment at
the metal ends of the fuse. (See Figure 2)
4. Place plug on a solid, flat surface. Insert new 2.5 Amp, 125 Volt fuse into fuse
compartment. Use a small screwdriver to secure the metal ends of the fuse into the
compartment.
CAUTION: Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
5. Slide fuse cover closed completely.
NOTE: If fuse cover is difficult to close, make sure the fuse is completely secured in place by pressing on metal ends
of the fuse.
CAUTION: Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be
removed. Discard product if the attachment plug is damaged.
Figure 2
Fuse
Fuse cover
Metal ends
3 YEAR LIMITED WARRANTY
This device has a limited warranty of 3 years from the original date of purchase against workmanship and defects in
material. If under normal use, your product fails to operate, please contact our customer service department at
info@getholmesfans.com. A refund or replacement will be provided to you with proof of purchase. Star Elite Inc. may
deny claims of damage caused by misuse or modifications of this product.
Warranty Service
Contact our customer service at www.getholmesfans.com/en/contact-us
or info@getholmesfans.com or 1-866-769-3166 (8:30 am - 5:00 pm EST) Monday-Friday.
Our team will be happy to assist.
www.getholmesfans.com
Instruction Manual
Item: 12211
Model: 32510380
12 Inch
Table Fan
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
WA R R A N T Y I N F O R M AT I O N
Printed In China
©
2023 Sunbeam Products, Inc. All rights reserved.
HOLMES
®
is a registered trademark of Sunbeam Products, Inc. used under license.
Distributed by Star Elite Inc., Montreal, Canada H3B 3X9
SEH024-090623
M A I N T E N A N C E
USER SERVICING INSTRUCTIONS
Follow these instructions to safely and correctly care for this fan.
REPLACEABLE FUSE
If the (2.5 Amp, 125 Volt) replaceable fuse blows, please visit our website at www.getholmesfans.com for information
on how to order a new fuse. Follow the below instructions to replace the fuse on the plug.
REPLACING THE FUSE
1. Unplug the fan.
Grasp plug and remove from the receptacle or other outlet device.
NOTE: Do not unplug by pulling on cord.
2. Open fuse cover, located on the top of the plug, by using your thumb or a flathead
screwdriver to slide the cover towards the prongs.
NOTE: Ensure the fuse cover is completely open before attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver to pry it from the compartment at
the metal ends of the fuse. (See Figure 2)
4. Place plug on a solid, flat surface. Insert new 2.5 Amp, 125 Volt fuse into fuse
compartment. Use a small screwdriver to secure the metal ends of the fuse into the
compartment.
CAUTION: Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
5. Slide fuse cover closed completely.
NOTE: If fuse cover is difficult to close, make sure the fuse is completely secured in place by pressing on metal ends
of the fuse.
CAUTION: Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be
removed. Discard product if the attachment plug is damaged.
Figure 2
Fuse
Fuse cover
Metal ends
3 YEAR LIMITED WARRANTY
This device has a limited warranty of 3 years from the original date of purchase against workmanship and defects in
material. If under normal use, your product fails to operate, please contact our customer service department at
[email protected]. A refund or replacement will be provided to you with proof of purchase. Star Elite Inc. may
deny claims of damage caused by misuse or modifications of this product.
Warranty Service
Contact our customer service at www.getholmesfans.com/en/contact-us
or [email protected] or 1-866-769-3166 (8:30 am - 5:00 pm EST) Monday-Friday.
Our team will be happy to assist.
www.getholmesfans.com
