Loading ...
Loading ...
Loading ...
7
ENGLISH
Accessories
WARNING:
Since accessories, other than those offered
by DeWALT, have not been tested with this product, use
of such accessories with this product could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact DeWALT. Call 1-800-4-DeWALT
(1-800-433-9258) or visit our website: www.dewalt.com
Cleaning
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Your DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.
Cutting PVC/PEX (Fig.K)
1. Mark the cutting point on the pipe.
2. Secure pipe to prevent it from moving while cutting.
3. Insert the pipe into the “V” notch for optimal cutting.
4. Align the blade with mark.
5. Depress the trigger of the impact driver.
6. After the tubing is fully cut, release the trigger .
7. Retract blade fully into housing for subsequent cut,
storage, or transportation.
Proper Hand Position (Fig.J)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the main handle
of the impact driver.
WARNING: Proper material preparation and installation is
the responsibility of the installing contractor.
WARNING: To reduce the risk of injury, always fully
retract the blade for transport or storage.
WARNING: Do not cut short pieces of material that
requires hands to be within 6" from the blade. Blade
is sharp.
CAUTION: Do not cut off pieces of tubing less than 1x
diameter of tubing for optimal cut.
Introduction
The DWAPVCIR PVC/PEX Cutter uses a compatible impact
driver to actuate a power screw which mechanically cuts
plastic tubing members.
• Forward setting: Squeezing the trigger with the impact
driver set to forward (clockwise) advances the cutting
blade. Fully releasing the trigger switch stops the
advancement of the blade.
• Reverse setting: Squeezing the trigger with the impact
driver set to reverse (counterclockwise) retracts the blade
into the housing.
WARNING: CUT OR AMPUTATION HAZARD. Never have
any part of your body near the blade or moving parts
during the cutting cycle or when the battery is installed
in the tool. Serious personal injury may occur.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Resetting Guide Plate (Fig. I)
Reset the guide plate
19
every time the blade is replaced or
whenever the blade becomes loose.
1. Advance blade
10
all the way forward by holding the
trigger on the impact driver.
2. Remove battery from impact driver.
3. Push blade cover/alignment guide
11
through the front slot
12
of the hook
13
and over the blade until the tabs
14
are
secured onto the blade.
NOTE: The arrow
15
should point to the open end of the hook.
4. Loosen plate screws
20
using a T10 screwdriver.
NOTE: The screws should remain attached but the guide
plates should be able to slide slightly.
5. Press the guide plates in so the front end lightly contacts
the blade and retighten the screws firmly.
6. Remove the blade cover/alignment guide prior to use.
4. Push blade cover/alignment guide
11
through the front slot
12
of the hook
13
and over the blade until the tabs
14
are
secured onto the blade.
NOTE: The arrow
15
should point to the open end of the hook.
5. Once the blade cover/alignment guide is set, pull back
the plug
16
to expose the set screw
18
.
6. Use 2.5mm hex wrench to loosen set screw until the
covered blade can be pulled forward through the front
slot of the hook.
7. Carefully remove the blade cover/alignment guide and
install onto new blade.
8. Insert new covered blade through the front slot and into
the PVC Cutter Attachment body.
9. Tighten set screw. Ensure the blade does not move.
10. Reinsert the plug.
11. Reset the guide plate as described in the RESETTING
GUIDE PLATE section..
Loading ...
Loading ...
Loading ...