Loading ...
Loading ...
Loading ...
9
ENGLISH
Speed Selection(Fig. A, F)
CAUTION: Because this tool has a separate speed
wheel for setting the speed (3,500 ‑ 29,500 rpm), the
tool will start at the speed where the speed wheel isset.
CAUTION: Never exceed the speed rating of the
accessory beingused.
Turning Tool On and Off (Fig. A)
CAUTION: Because this tool has a separate speed
wheel for setting the speed (3,500 ‑ 29,500 rpm), the
tool will start at the speed where the speed wheel isset.
1. To turn the tool on, depress the ON/OFF button
1
. The
tool will immediately run at the speed which isselected.
NOTE: Do not attempt to start tool with spindle lock
engaged. It will notrun.
2. To turn the tool off, depress the ON/OFF button
1
a
secondtime.
LED Worklight (Fig. A)
CAUTION: When using the worklight for purposes
other than intended, be sure to remove all
accessories. Unused accessories could cause injury
or propertydamage.
CAUTION: Do not stare into the LED. Serious eye
injury couldresult.
When the tool is activated by depressing the ON/OFF
button
1
, the LED work light
9
will automatically turn on.
The LED work light will turn off when the tool is turnedoff.
There are two ways to hold the rotary tool, grip the main
handle
2
like a pencil between your thumb and forefinger or
holding by grasping the main handle
2
in your palm.
Proper Hand Position (Fig. A, E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
OPERATION
WARNING:
To reduce the risk of serious personal injury,
keep away from the ON/OFF button while making any
adjustments or removing/installing attachments or
accessories. An accidental start‑up can causeinjury.
5. Turn the collet nut
8
clockwise to tighten the collet
nut
8
securely onto the accessorymandrel.
Note: The collet
7
was designed to be hand tightened and
loosened only. Accessories naturally self tighten during use.
A wrench is provided with the tool for loosening. You should
never need to tighten the collet nut
8
with a wrench. If a
wrench is needed, use only the wrench provided. Do not
use tools that will mar the finish and could break the collet.
Always ensure there is some accessory in the collet before
tightening. Tightening an empty collet can crackit.
6. When finished, release the spindle lock button
6
.
NOTE: If an accessory causes vibration it can usually be
improved by loosening the collet nut
8
, pushing the
accessory in as far as it will go and rotating it 1/4 turn
then retightening the collet
7
.
Changing Accessories (Fig. A, D)
WARNING: Do not use accessories with a mandrel
length exceeding 1” (25mm). Ensure that the exposed
mandrel length is no more than .5” (13mm) after
inserting accessory intocollet.
WARNING: Use only accessories up to 1” (25mm) in
diameter and rated at 30,000 RPM or greater.
WARNING:
Do not attach a toothed saw blade. Such
blades create frequent kickback and loss of control.
Reference these earlier sections for accessory related
information and precautions:
‑ ADDITIONAL SPECIFIC SAFETY RULES
‑ FURTHER SAFETY INSTRUCTIONS FOR ALL OPERATIONS
‑ ADDITIONAL SAFETY INSTRUCTIONS FOR GRINDING
AND CUTTING‑OFF OPERATIONS
‑ ADDITIONAL SAFETY RULES FOR ROTARY TOOLS
Accessories are held in place by a collet
7
and collet nut
8
as
shown in Fig. D.
To Insert an Accessory
1. Turn tool off and allow it to come to a completestop.
2. Press and hold the spindle lock button
6
and grasp
the collet nut
8
.
3. Turn the collet nut
8
counterclockwise until it isloose.
4. Insert the accessory mandrel into the collet
7
to the full
depth of the gripping jaws of the collet and at least half
of the full mandrel length.
Spindle Lock Button (Fig. A, C)
CAUTION: Turn tool off before changingaccessories.
1. To lock the spindle
5
for changing accessories, press
and hold the spindle lock button
6
, the spindle
5
will lock in position allowing you to install or remove
the accessories as directed in thismanual.
2. To unlock the spindle
5
, release thespindle lockbutton
6
.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and lock off the tool before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can causeinjury.
See tables below for details.
Charge LED Indicator
Charging One Green LED
Charging Two Green LEDs
Charging Three Green LEDs
Charging Four Green LEDs
Fully Charged Five Green LEDs
Hot/Cold Pack Delay* Five Orange LEDs
* Orange charge indicator LEDs will be illuminated during
this operation. Once the battery pack has reached an
appropriate temperature, the orange LEDs will turn off and
the tool will resume the normal chargingprocedure.
Loading ...
Loading ...
Loading ...