LC 130 User Manual

Loading ...

MANUAL

A INSTALLING THE HEATER

Carefully remove your heater from the box and check the contents.

In addition to the heater you also need to have:

 a manual fuel pump

 a transportation cap

 these directions for use

฀Keep฀the฀box฀and฀the฀packaging฀materials฀(Fig.฀A)฀for฀storage฀and/or฀

transportation.

Open the lid of the removable tank  and remove the piece of cardboard.

Fill฀the฀removable฀tank฀as฀indicated฀in฀Section B.

The floor should be firm and completely level. Reposition the heater, when it

is not level. Do not try to correct the situation by placing books or other

goods under the heater.

Insert the plug ฀into฀the฀wall-socket฀(230฀Volts฀-฀AC฀/฀50฀Hz)฀and฀set฀the฀

correct time using the adjustment keys 

(refer to Section C).

Your heater is now ready for use.

SET ALTITUDE

If฀the฀heater฀is฀used฀at฀a฀height฀of฀800฀m฀to฀1300฀m,฀use฀the฀altitude฀mode฀1.฀

Push฀the฀altitude฀button฀ with thin rod like a clip and plug into the outlet

simultaneously. Then “1

” will be shown on the display.

If฀the฀heater฀is฀used฀at฀a฀height฀of฀1300฀m฀to฀1900฀m,฀use฀the฀altitude฀mode฀

2.฀After฀setting฀the฀altitude฀mode฀1,฀push฀the฀altitude฀button฀ with thin rod

and plug into the outlet simultaneouosly again. Then “2

” will be shown on

the display.

Switch฀off฀the฀altitude฀mode฀by฀pressing฀the฀altitude฀button฀ and into the

outlet simultaneously after setting altitude mode 2. Then “0” will be shown

on the display and “

” will be disappeared.

NOTE: When the altitude mode 1 is set, the altitude mark “ ” is lit on the display.

When the altitude mode 2 is set, the altitude mark “

” is blinking during

operation.

NOTE: In the event of power failure or disconnection of heater, the altitude setting

will remain.

Do฀not฀use฀the฀heater฀at฀a฀height฀of฀over฀1900฀meters.

SWITCH THE VOLUME

This฀heater฀can฀be฀switched฀the฀buzzer฀sound฀volume.฀The฀initial฀setting฀is฀in฀

High฀level.

Push฀the฀SAVE฀key฀฀and฀holding฀it฀down฀for฀more฀than฀3฀seconds,฀then฀the฀

buzzer฀sound฀volume฀is฀switched฀from฀High฀to฀Low.

Push฀the฀SAVE฀key฀฀and฀holding฀it฀down฀for฀more฀than฀3฀seconds฀again,฀

then฀the฀buzzer฀sound฀volume฀is฀switched฀from฀Low฀to฀High.

NOTE:

The฀volume฀level฀is฀Low฀and฀High฀only,฀but฀the฀alarm฀by฀safety฀device฀

sounds฀in฀High฀level.

NOTE:

When the heater has been unplugged or after a power failure, the volume

will฀be฀the฀initial฀setting฀High.

Loading ...

Zibro LC 130

User Manual - Page 6