Loading ...
Loading ...
Loading ...
11
English
Cleaning
WARNING: Blow dirt and dust out
of all air vents with clean, dry air at least once a
week. To minimize the risk of eye injury, always
wear ANSI Z87.1approved eye protection when
performingthisprocedure.
WARNING: Never use solvents or other
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
aliquid.
MAINTENANCE
WARNING: To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can causeinjury.
Rewinding Spool from Bulk Line (Fig.L, M)
Use Only .065" (1.65 mm) Round
Diameter Line
Bulk line is also available for purchase from your localretailer.
nOTE: Hand wound spools from bulk line are likely to
become tangled more frequently than CRAFTSMAN factory
wound spools. For best results, factory wound spools
arerecommended.
1. Disconnect the plug from the power sourceRemove
battery fromappliance.
2. Remove the empty spool from the appliance as
described in Replacing SpoolAssembly.
3. Remove any remaining cutting line from thespool.
4. Make a fold
22
at the end of the cutting line at about
3/4" (19 mm). Feed the cutting line into one of the line
anchoring slots
23
.
5. Insert the 3/4" (19 mm) end of the bulk line into the
hole
24
in the spool adjacent to the slot. Make sure the
line is pulled tight against thespool.
6. Wind the cutting line onto the spool in the direction of
the arrow on the spool. Make sure to wind the line on
neatly and in layers. Do notcrisscross.
7. When the wound cutting line reaches the recesses
25
,
cut theline.
8. Fit the spool onto the appliance as described in
Replacing SpoolAssembly.
nOTE: Other replacement parts (guards, spool caps, etc.)
are available through authorized service centers. To find
your local service location call: 1‑888‑331‑4569 or visit
www.craftsman.com.
Replacing Spool Assembly (Fig. K)
WARNING: The use of any accessory
not recommended by CRAFTSMAN for use with this
appliance could behazardous.
WARNING: Do not use any blades,
or any accessory or attachment other than those
recommended by CRAFTSMAN on this trimmer/edger.
Serious injury or product damage mayresult.
Reload nylon line (either bulk or prewound replacement
spool) as shown in thismanual.
USE ONLY .065" (1.65 mm) DIAMETER ROUND NYLON
MONOFILAMENT LINE. Do not use serrated or heavier gauge
line, as they will overload the motor and cause overheating.
This line is available at your local dealer or authorized
servicecenter.
1. Remove battery fromappliance.
2. Press the release tabs
20
on the spool cap
19
, and
remove the spool cap from the spool housing
12
.
3. For best results, replace spool with CRAFTSMAN
ModelCMZST065.
4. If lever in base of housing becomes dislodged, replace in
correct position before inserting new spool intohousing.
5. Remove any dirt and grass from the spool cap and
spoolhousing.
6. Unfasten the end of the cutting line and guide the line
into the eyelet
17
.
7. Take the new spool and push it onto the boss
21
in the
housing. Rotate the spool slightly until it isseated.
8. The line should protrude approximately 5-3/8" (136mm)
from thehousing.
9. Align the release tabs on the spool cap with the slots in
the spoolhousing.
10. Snap the spool cap back on by depressing release tabs
and pressing into spoolhousing.
11. Push the cap onto the housing until it snaps securely
intoplace.
nOTE: Make sure that cover is fully positioned, listen for
two audible clicks to ensure both release tabs are correctly
located. Power the appliance on. In a few seconds or less
you’ll hear the nylon line being cut automatically to the
properlength.
CAUTION: To avoid appliance damage, if
the cutting line protrudes beyond the trimming blade,
cut it off so that it just reaches theblade.
1. Remove battery fromappliance.
2. Press the release tabs
20
on the spool cap
19
, and
remove the spool cap from the spool housing
12
.
3. Pull the nylon line spool out and clear any broken line or
cutting debris from the spool area.
4. Fit the spool onto the appliance as described in
Replacing SpoolAssembly.
Loading ...
Loading ...
Loading ...