Loading ...
Loading ...
Loading ...
Installation issues
• You may not need an adapter. After original aerator and
washer are removed, try attaching the device to your
faucet. If adapter is needed, check to make sure the old
aerator washer was removed and only the new adapter
washer is being used.
• Make sure device is level to the faucet in order for the
threaded mounting nut to attach to the faucet threading.
Turn counterclockwise to tighten.
Water leaks around the
faucet adapter or threaded
mounting nut
• Check to see that the washer and screen are placed
in the threaded mounting nut.
• If using an adapter, make sure the adapter is
hand-tightened securely to the faucet.
Slow water flow, after 3 months
of use, in the filtered position
• When filter is near end of life, water will run slower
in the filtered position. Replace your filter to ensure
contaminant removal at the certified levels.
Water leaks around the
filter cover
• Try tightening faucet mount back cover all the way until
tight. If that doesn’t solve the problem, remove the filter
cartridge and reinstall the filter cartridge again.
Difficulty removing the old filter
cartridge to replace the filter
• Remove the device from the faucet by turning
the threaded mounting nut clockwise.
• Remove the cover.
• Slowly turn or twist the filter cartridge. This will help
loosen the filter.
CleanSensor
™
Monitor Troubleshooting
Technical Specifications:
FILTER CAPACITY: 100 gallons (378 liters)/up to 3 months
RATED SERVICE FLOW: 0.52 gallons/minute (2.0 liters/minute) at 60 psig
MAXIMUM TEMPERATURE: 100°F (38°C) MAXIMUM WORKING PRESSURE: 100 psig (690 kPa)
MINIMUM TEMPERATURE: 34°F (1°C) MINIMUM WORKING PRESSURE: 20 psig (138 kPa)
For system to perform as shown in the Performance Data Sheet, it is necessary to replace the filter
when it exceeds filter capacity (100 gallons).
Testing was performed under standard laboratory conditions, actual performance may vary.
The contaminants or other substances removed or reduced by this water filter are not necessarily in
all users’ water. Do not use with water that is microbiologically unsafe, or of unknown quality, without
adequate disinfection before or after the system. Systems that are certified for cyst reduction may be
used on disinfected water that may contain filterable cysts. Individuals requiring water of certain
microbiological purity should consult their physician. Replacement filters may be purchased at most
retail outlets or at pur.com.
PFM100B, PFM150W, PFM400H, PFM450S, PFM470S
Systems Tested and Certified by NSF International against NSF/ANSI Standards 42, 53 and 401 for the
reduction of the claims specified on the Performance Data Sheet.
You can fully recycle all of your PUR products and packaging free of charge
through our partnership with TerraCycle
®
. Join the PUR Brigade
®
to recycle
your old products and help us create a cleaner future. Please visit
PUR.com/recycle to learn more.
Filter is working
Change filter soon
End of filter life
When filtered water is activated the CleanSensor™ Moniter indicates filter status
and guarantees you will always have safer and healthier filtered, drinking water.
Green light will flash 6 times as you begin to use the filter. Replacement of filter
cartridge resets the light.
The CleanSensor™ Moniter changes color depending on how long filter has been
in use or how much water has been filtered. Filter will reach end of life at 100+
gallons or 90+ days.
The CleanSensor™ Moniter
contains a non-replaceable battery.
The battery will eventually stop
working but the filter is still functional.
Use and Care
Before first use, run cold water for 5 minutes in filtered position.
During filter flush, it is normal to see cloudy water and hear the sound of
water pushing air out of the filter cartridge. Flushing removes any loose
materials, which is normal.
Prior to each use, run cold water for 5 seconds in filtered position to activate filter.
Never run hot water through the filter.
Do not use the water above 100˚F/38˚C as this may alter the filter.
Use cold water only.
Change your filter every three months for best performance.
To change the filter or if you need sink space, remove the device from your
faucet by unscrewing the threaded mounting nut. After each new filter
cartridge is installed, run cold water for 5 minutes to flush it.
Clean the exterior of the faucet mount housing with a damp sponge or soft cloth.
A mild dishwashing liquid may also be used. Using anything else
to clean your faucet mount could result in damage to the unit.
For more information, please visit PUR.com/support
Two Year Warranty
Kaz (Warrantor), warrants your PUR Faucet Filtration Unit (PFM100B, PFM150W, PFM400H, PFM450S,
PFM470S) for two (2) years from the date of purchase (except for the filter cartridge which is warranted
for 30 days) against all defects in materials and workmanship, when used in compliance with the owner’s
manual.
If the product proves to be defective within two years from the date of purchase, call 1-800-787-5463.
The warrantor assumes no responsibility for incidental or consequential damages; for damages arising out
of misuse of the product or use of any unauthorized attachment; or for damages resulting from the use of
the product with a defective water faucet. Some states do not allow the exclusion or limitation of incidental
or consequential damages; so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may have other legal rights which vary from state to
state. System complies with applicable state and local regulations.
Should service be required or you have any questions regarding how to use your PUR product, please
contact PUR Consumer Relations: PUR.com/support 1-800-PUR-LINE [email protected]
Loading ...
Loading ...
Loading ...