Loading ...
Loading ...
Loading ...
7
ENGLISH
Blow Tube Assembly (Fig. D)
WARNING: Do not operate blower
without tube securely in place. Never reach down into
housing through tubehole.
WARNING: Always remove the battery
when you leave blower unattended or when storing,
checking, adjusting, cleaning, or working onblower.
1. To attach the lower tube
4
to the upper tube
5
, align
the peg
9
of the upper tube
5
with the notch
10
of
the lower tube opening
11
and push the two tubes
together until the tube locks
6
engage the blower tube
and an audible click isheard as shown in Fig. D.
2. To attach the blower tube assembly
12
to the power
head
3
, align the peg
13
on the power head with
the notch
14
on the blower tube assembly opening as
shown in Fig. D.
3. Push the blower tube assembly onto the power head
until the tube locks
6
engage the blower tube
5
and an
audible click isheard.
4. Pull on the blower tube assembly
12
to ensure it is
secured inplace.
5. To remove the blower tube assembly, squeeze both
tabs
6
on the side of the power head and pull the
blower tube assemblyoff.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can causeinjury.
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in theslots.
VersaTrack™
WARNING: Do not charge batteries while
charger is hung onTrackwall.
CRAFTSMAN chargers can be stored on CRAFTSMAN
VersaTrack™ Trackwall. Hooks and accessories are sold
separately. Please refer to the VersaTrack™ Trackwall accessory
sheet for furtherinformation.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Wall Mounting
Some CRAFTSMANchargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1” (25.4mm) long, with a screw head
diameter of 0.28–0.35” (7–9mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery packlife.
A cold battery pack may charge at a slower rate than a warm
batterypack.
The hot/cold pack delay will be indicated by the green light
continuing to blink but with the red light continuously
ON. Once the battery pack has reached an appropriate
temperature, the red light will turn OFF and the charger will
resume the chargingprocedure.
Electronic Protection System
Li‑Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to berecharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulatedtrailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local servicecenter.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the batterypack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non-metallic brush. Do not use
water or any cleaningsolutions.
Loading ...
Loading ...
Loading ...