Loading ...
Loading ...
Loading ...
Check that hose isnot twisted or kinked
and issecurely in place.
A B C
str strap
9mPut "hock" end of drain hose
in laundry tub or standpipe Tightly wrap
the shipping strap around the drain
hose and laundry tub or standpipe as
shown in Figures A and B Push plug into
the nearest hole in the shipping strap
If the water inlet faucets and drain
standpipe are recessed, put "hook" end
of drain hose in standpipe. Tightly wrap
the shipping strap around the drain
hose and faucet body (not the handles
or stems) as shown in Figure C. Push plug
into the nearest hole in the shipping
strap
Hose must be cut exactly to length so
"hook" end isheld tightly over edge of
standpipe.
If drain hose cannot be strapped in
place, it must be cut exactly to
length so the "hook" end is held D
tightly over the edge of the
tub or standpipe. See
Figure D.
If a longer drain hose is
needed, drain hose (Part
No. 388423) and hose
extension kit (Part NO.
285442) are available
from a Whirl )col- /_r
authorized ii
parts ,,
distributor, if
drain hose
must be
shortened, _use hose kit
(Part No.
285442)
Note: If washer/dryer is moved Io adjust
drain hose, the washer/dryer must be
leveled again. Repeat Steps 15-17.
P#ace cardboard under the
washer/dryer and carefufly move
washer/dryer to avoid damaging floor
covering.
AA
ZO • IfyOU did not remove the
access panel inStep 1I,remove three
Phillips-head screws and one bumper,
located at the top of the access panel
Set the panel, screws and bumper
aside
1 _Determine the length of
exhaust vent that is needed to connect
the dryer to the exhaust hood. (See
"Exhaust requirements," Panels C and D,)
2• Connect exhaust vent to
washer/dryer and then to the exhaust
hood
• Use the straightest path possible to
avoid 90°turns.
• Use clamp to seal all joints in the
exhaust system.
• Use caulking compound to seal
exterior wall opening around exhaust
hood,
3•CHECK ELECTRICAL
REQUIREMENTS.BESUREYOU HAVE
CORRECT ELECTRICALSUPPLYAND
RECOMMENDED GROUND METHOD.
Check the Installation Instructions to see
that you have completed each step
Complete any missed steps before you
continue,
installed See parts list, Panel D. If there is
an extra part, go back through steps to
see which step was skipped
5• Check that you removed all
the shipping pieces including the
shipping strap with its 2 cotterpins and
plug, Dispose of all materials in proper
manner.
If you do not remove the shipping strap,
your washer/dryer may "walk" away
from its location•
uOlITY
safetyglasses
gloves " Phiiiips screwdriver
e_quim<l)
,_rewdtJvef
6• Check that you have all of
your tools.
7• Turn on water faucets and
check for leaks. Tighten couplings if
there isleaking. Do Not oveffighten; this
could cause damage to faucet.
8mReplace access panel Be
sure to tighten the three Phillips-head
screws at the top of the access panel.
Replace the bumper under the center
screw.
9_Read the Use and Care
Guide to fully understand your new
washer/dryer. Open dryer door. Check
to be sure lint screen is in its proper
position. Wipe out drum.
0 • Plug power supply cord into
grounded outlet. Reconnect the power
supply. Now start the washer and allow
it to complete the regular cycle
1_Stad dryer and allow it to
complete a full heat cycle to make sure
it isworking properly.
You have successfully installed your
new Whirlpool washer/dryer. To get the
most efficient use from your new
Whirlpool washer/dryer, read your
Use and Care Guide.
Congratulations!
Keep Installation Instructions nearby
where you can refer to them• They'll
make reinstalling your Whirlpool
washer/dryer in another home as
easy as the first installation•
Recessed and closet
installation instructions
Thiswasher/dryer may be installed in o
recessed area or closet.
The installation spacing isin inches and
isminimum allowable. Additional
spacing should be considered for ease
of installation, servicing and compliance
with local codes and ordinances
If closet door is installed, the minimum
unobstructed air openings in top and
botlom are required. Louvered doors
with equivalent air openings are
occeptoPke. Closet instaUation must be
exhausted.
Other Installations must use the minimum
dimensions indicated
Recessed area minimum
installation spacing
0_* 0"* O"*
Oooo cO
Rwasher
side view front view
Product dimensions
Recessed, non-exhausted installation must use only the
rear exhaust po_fion and Exhaust Degector Part NO. 694609.
Note: If recessed installotlan is exhausted to the slde or rear,
6" must be available above the washerldryer but all other
spacing can be 0".
Most InstallaSon will require at least Sinch
clearance behind the dryer for the dryer vent.
_- _ Locanon must be large enough to fully open dryer
Idoor.
6'r
+ a.,,.-q
72-3/4"
side view
Closet installation must be exhausted outdoors.
WARNING - To reduce the risk of fire, this appliance MUST BEEXHAUSTED OUTDOORS.
closetdoor
/
3"
o
48 $q. in. *"
+
front view side view
• Additional clearances for wag, door ancl flOOrmoldlngs may be requ&red or if external exhaust
elbow is used.
** Opening Is mlnlmum for closet door. Louvered door with equivalent air openings isacceptable.
***Additional space may be needed for exhaust elbow,
13.11/16'I _a_ 13.111)6 -
5,,
recess
depth
1-I12"
hot
watel
inlet
exhaust
ouOet
13-II
recess width
rear view
Kits Make Installation Easy
•Provides 41/2"
clearance between
dryer and wall
eSnap-Lockfiflings
Part #4396028
4.Total kit length
8 feet
4)Additional vent can
be snapped between
sections for
Iongerruns
Kit Contains:
2- 4' ventsectionswith attachedcloseelbows
1- Wall platefor closeclearanceinstallations
2- 4"clamps
"Aseasy as 1-2-3"
,II
--_ Wall _ _
Step 1Step 2Step 3
Clamp one Extend vent From over the
elbowlvent upward, almost top, snap vent
section to wall to top of dryer, together.
arid one to then push dryer
dryer, to wall.
Dura Safe and Sure Oo,lrle¢_ are TrademarKs of WhirlpOOl U S A
• Provides2 1/2" clearance
between dryerand wall
•Great forcloset
installations
• 0"-18", 16"-2G" or
29"- 50" periscopes
include one male
snap-lockfitting,
one extra long
draw-bandcollar
and one clamp 0%18": Part #4396037
15'*-26" : Part #4396011
2S"-56" : Part #4396th 4
0"-18" Periscope
Usewhenventoutlets _
overlapor areoffset _
betrimmedtolit rt#4396037
18"-29" and 29"-50" Periscope
Swivelcollar
wail connection
,Sectionsseparate,
fittingscanface
sameor opposite
Telescoptns , Swivelcollar
aevelededges
installations
18"-2_': Pan#4396011
Extra long
for dryer
COllnoction
29"- 55" : Pan #4396014
For more information,
or to easily place your
order, call
1-800-442-9991
To have your venting
professionally installed,
call
1-800-253-1301
for the nearest
authorized service
provider.
Panel F Panel G
Loading ...