Ancona AN-18056SS 30" 160 CFM Convertible Under Cabinet User Manual

Under Cabinet Range Hood

User Manual

and

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

Carefully read the important information

regarding installation, safety and maintenance.

Keep these instructions for future reference.

MAAN18056SS-01

2023-02-08

— 2 —

INSTALLERS - Start Here

Safety Instructions are on pages 4 and 5 and

Installation Instructions are on pages 8 to 14.

Please perform these steps:

1. Read the safety instructions.

2. Read all instructions in the Installation section of

this manual BEFORE installing the range hood.

3. Remove all packing materials.

4. When nished, make sure to leave these instructions with the consumer.

5. Installation is to be done by a qualied technician only. However, the

ultimate responsibility for proper installation falls to the owner.

Product failure due to improper installation is not covered under the Warranty.

CONSUMERS - Start Here

Safety Instructions are on pages 4 and 5 and Operating Instructions are

on pages 15 to 17.

Please perform these steps:

1. Read the safety instructions.

2. Read all instructions in the manual BEFORE operating the range hood.

3. Remove all packing materials.

4. Installation is to be done by a qualied technician only. However, the

ultimate responsibility for proper installation falls to the owner.

Product failure due to improper installation is not covered under the Warranty.

Before You Begin

Hardware Note: For safety reasons, range hood mounting screws and

anchors will not be included due to the variation of cabinetry constructions

and wall material. Please consult your installation specialist regarding the

optimal type of mounting screws and wall anchors to suit your home’s

construction.

— 3 —

Before You Begin ............................................................................................................................... 2

Table of Contents .............................................................................................................................. 3

Important Safety Information ............................................................................................................ 4

Included Parts ................................................................................................................................... 6

Range Hood Dimensions .................................................................................................................. 7

Specications .................................................................................................................................... 7

Installation ......................................................................................................................................... 8

Step 1 - Read the Safety Instructions ............................................................................................ 8

Step 2 - Unpack Range Hood and Prepare Tools .......................................................................... 8

Step 3 - Plan Desired Location ...................................................................................................... 8

Step 4 - Test Unit Functions .......................................................................................................... 8

Step 5 - Venting Installation Guidelines ......................................................................................... 9

Step 6 - Preparations ................................................................................................................... 11

Step 7 - Remove Accessories ...................................................................................................... 11

Step 8 (External Ventilation Only) - Attaching Vent/Damper and Panel Piece ............................. 12

Step 9 - Electrical Connection ..................................................................................................... 13

Step 10A - Wall installation .......................................................................................................... 14

Step 10B - Under the cabinet installation .................................................................................... 14

Step 11 (External Ventilation Only) - Venting ............................................................................... 14

Operation ........................................................................................................................................ 15

Power ........................................................................................................................................... 15

Light ............................................................................................................................................. 15

Troubleshooting............................................................................................................................... 15

Maintenance.................................................................................................................................... 16

Hood Cleaning ............................................................................................................................. 16

Replacing the Light ...................................................................................................................... 16

Use and Care Information ............................................................................................................... 17

Table of Contents

— 4 —

Important Safety Information

• Theinstallationinthismanualisintended

for qualied installers, service technicians or

persons with a similar qualied background.

Installation must be done by qualied

professionals and in accordance with all

applicable codes and standards, including

re-rated construction.

•

The range hood may have very sharp

edges; please wear protective gloves if it is

necessary to remove any parts for installing,

cleaning or servicing.

•

Activating any switch to ON position before

completing installation may cause damage or

electric shock.

• Duetothesizeofthisrangehood,atwo-

person installation is recommended.

To reduce the risk of ﬁre, electric shock, or

injury to persons:

• Forgeneralventilatinguseonly.DO NOT use

toexhausthazardousorexplosivematerials

and vapours.

• WARNING: To Reduce The Risk Of Fire Or

Electric Shock, Do Not Use This Fan With Any

Solid-State Speed Control Device.

• Thecombustionairowneededforsafe

operation of fuel-burning equipment may be

affected by this unit’s operation. Follow the

heating equipment manufacturer’s guideline

and safety standards such as those published

by the National Fire Protection Association

(NFPA), and the American Society of Heating,

Refrigeration and Air Conditioning Engineers

(ASHRAE), and other local code authorities.

• Beforeservicingorcleaningtheunit,switch

power off at service panel and lock the service

disconnecting means to prevent power from

being switched on accidentally. When the

service disconnecting means cannot be

locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

• Cleangrease-ladensurfacesfrequently.To

optimizeperformanceandtodisperseair

properly, make sure to vent air outside. DO

NOT vent exhaust into spaces between walls,

crawl spaces, ceilings, attics or garages.

•

Ducted fans MUST always be vented to

the outdoors.

• ThisunitMUSTbegroundedandusedwith

metal ductwork only.

• Sufcientairisneededforpropercombustion

and exhausting of gases through the duct to

prevent back drafting.

• Whencuttingordrillingintowallorceiling,be

careful not to damage electrical wiring or other

hidden utilities.

• Allelectricalwiringmustbeproperlyinstalled,

insulated and grounded.

•

Old ductwork should be cleaned or replaced

if necessary to avoid the possibility of a

grease re.

•

Check all joints on ductwork to ensure

proper connection; all joints should be

properly taped using a certied aluminum

or foil tape.

• Usethisunitonlyinthemannerintended

by the manufacturer. If you have questions,

contact the vendor.

READ AND SAVE THESE

INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Read and follow all instructions before using the range hood to prevent the risk of re, electric shock,

personal injury, or damage when using the range hood or appliances with the range hood. This guide

does not cover all possible conditions that may occur. Always contact your service technician or

manufacturer about problems that you do not understand.

— 5 —

Important Safety Information

WARNING: TO REDUCE RISK OF A RANGE

TOP GREASE FIRE:

a) Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on

low or medium settings.

b) Always turn range hood ON when cooking at

highheatorwhenambéingfood(i.e.Crepes

Suzette,CherriesJubilee,etc.).

Clean ventilating fans frequently. Grease should

not be allowed to accumulate on fan or lter.

Before servicing or cleaning unit, unplug and

disconnect the hood from the power supply.

d)Useproperpansize.Alwaysusecookware

appropriateforthesizeofthesurfaceelement.

WARNING: TO REDUCE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING *

a) S

MOTHER FLAMES with a close-tting

lid, cookie sheet, or metal tray, then turn

off the burner. BE CAREFUL TO PREVENT

BURNS.Iftheamesdonotgoout

immediately, EVACUATE AND CALL THE

FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may

be burned.

c) DO NOT USE WATER, including wet dishcloths

or towels - a violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a Class A, B, C

extinguisher, and you already know how to

operate it.

2) The re is small and contained in the area

where it is started.

3) The re department is being called.

You can ght the re with your back to an exit.

* Based on “Kitchen Fire Safety Tips”

published by NFPA

To reduce the risk of injury to persons in the

event of a gas leaks:

• Extinguishanyopename.

•

DO NOT turn on the lights or any type of appliance.

• Openalldoorsandwindowstodispersethe

gas. If you still smell gas, call the gas company

and re department.

Your safety and the safety of others is very

important. We have provided many important

safety messages in this manual and on your

appliance. Always read and obey all safety

messages. All safety messages outline any

potentialhazards,howtoreducethechanceof

injury, and possible risks if the instructions are not

followed.

READ AND SAVE THESE

INSTRUCTIONS

— 6 —

Included Parts

Hardware Note: For safety reasons, range hood mounting screws and anchors will

not be included due to the variation of cabinetry constructions and wall material.

Please consult your installation specialist regarding the optimal type of mounting

screws and wall anchors to suit your home’s construction.

Range Hood

Filter

4 + 1 ScrewsRectangular Vent/Damper Panel piece

— 7 —

Range Hood Dimensions

Speciﬁcations

Body Design Stainless Steel

Power Rating 120V/60Hz(cETLusCertied)

Total Input Power 52 W (50 W + 2 W)

Motor Input Power 50 W

Amperage 0.43 A

Speed Control Levels 2 Speeds

Interference Protection Radio Frequency Interference Protected

Motors Single Motor

Fan Type Centrifugal Squirrel Cage

Controls Rocker switch

Filtration Aluminium lter with charcoal cotton sheet

Lighting 1 × 2 W LED

Light Intensity Levels 1

VentingSize 3 1/4 × 10 inch (8.3 cm × 25.4 cm) rectangle, top or rear

or purchase separately top 6 inches (15.3 cm) round

29.9” (76 cm)

9.9” (25.2 cm)

3.1” (8 cm)

11.8” (30.1 cm)

4.7” (12 cm)

17.5” (44.5 cm)

9” (22.9 cm)

27.8” (70.6 cm)

9.9” (25.2 cm)

3.1” (8 cm)

27.8” (70.6 cm)

— 8 —

STEP 1

Read the Safety Instructions

• It is very important to read the safety instructions on pages 4 and 5.

IMPORTANT: It is the installer’s responsibility to comply with installation clearances.

STEP 2

Unpack Range Hood and Prepare Tools

• Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6.

• DO NOT remove the protective lm covering the appliance until the installation is fully completed.

• Consult a qualied and trained installer or check local codes for makeup air requirement, if any.

STEP 3

Plan Desired Location

• Plan a desirable location that ts all requirements in the Safety and Installation sections of this manual. Plan where

and how the ductwork will be installed.

• A straight or short duct run will allow the unit to perform most efciently. Long duct runs, elbows and transitions

will reduce the performance of the unit. Each elbow is equivalent to 5 to 10 feet (1.5 m to 3 m) of straight run.

• If ductwork is already installed: ensure ductwork is free from debris.

STEP 4

Test Unit Functions

• Plug the unit in and test all of the functions before installing.

• Placetherangehoodonaat,stablesurface.Connecttherangehoodtoadesignatedstandardoutlet(120-Volt,60Hz,

AC only) and turn on the range hood. Verify all operations of the range hood by referring to

Range Hood Operations.

• Turn power On in control panel.

• Check all lights and fan operations.

WARNINGS:

• PleasemakesuretoreadALLsafetyinstructionsonpages4and5.

• Usetwoormorepeopletomoveandinstallrangehood.

• Failuretofollowtheseinstructionscanresultinseriousinjury.

Installation

— 9 —

Installation

STEP 5

Venting Installation Guidelines

• The following steps are for exterior ventilation.

Height and Clearance

IMPORTANT:

•

Vent system must terminate to the outside (roof or side wall).

• DONOT

terminate the vent system in an attic or other

enclosed area.

• DONOTuse4in(10.2cm)laundry-typewallcaps.

• Usemetal/aluminumventonly.Arigidmetal/aluminum

vent is recommended.

• DONOTuseaplasticvent.

• Alwayskeeptheductcleantoensureproperairflow.

• Calculatethefollowingfiguresbeforeinstallation:

1. Distance from the floor to the ceiling

2. Distance between the floor and the countertop/stove

A distance of 24 in to 30 in (61 cm to 76.2 cm) is

recommended between stove top and the bottom of

range hood. 30 in (76.2 cm) minimum is required for

gas stove tops.

4. Height of hood and duct cover.

For the most efficient and quiet operation:

• Itisrecommendedthattherangehoodbevented

vertically through the roof through 6 in. (15.3 cm) round,

or through the roof or wall 3-1/4 × 10 in. (8.3 cm × 25.4

cm) rectangular duct or bigger metal/aluminum vent

work.

• Thesizeoftheventshouldbeuniform.

• Usenomorethanthree90°elbows.

•

Make sure there is a minimum of 24 in (61 cm) of

straight vent between the elbows if more than one

elbow is used.

• DONOTinstalltwoelbowstogether.

•

The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

• Theventsystemmusthaveadamper.Ifrooforwall

cap has a damper, you may remove damper flaps from

damper to increase air flow.

• Onlyoneflangeisneededintheairductsystem,either

on top of the motor or outside.

•

Use silver tape or duct tape to seal all joints in the

vent system.

•

Use caulking to seal exterior wall or roof opening

around the cap.

24 in. (610 mm) Min / 30 in. (762 mm) Max

— 10 —

IMPORTANT:

•

A minimum of 6 in. (15.3 cm) round or 3-1/4 × 10 in. (8.3

cm × 25.4 cm) rectangular duct must be used to maintain

maximum airflow efficiency.

• Alwaysuserigidtypemetal/aluminumductsifavailableto

maximizeairflowwhenconnectingtoprovidedduct.

• PleaseuseDuctRunCalculationbelowtocompute

total available duct run when using elbows, transitions

and caps.

• ALWAYS,whenpossible,reducethenumberor

transitions and turns. If long duct run is required,

increaseductsizefrom6in.(15.3cm)to7in.(17.7

cm) or 8 in. (20.3 cm). If a reducer is used, install a

long reducer instead of a pancake reducer. Reducing

ductsizewillrestrictairflowanddecreaseairflow,thus

reduceductsizeasfarawayfromopeningaspossible.

• Ifturnsortransitionsarerequired,installasfaraway

from opening and as far apart, between two (2), as

possible.

• Minimummountheightbetweenstovetoptohood

bottom should be no less than 24-inch (61 cm) for

electric cook tops and minimum of 30-inch (76.2 cm)

for gas stove tops and no higher than 30-inch (76.2 cm)

for electric cook tops.

• Itisimportanttoinstallthehoodatthepropermounting

height. Hoods mounted too low could result in heat

damageandfirehazard;whilehoodsmountedtoohigh

may be hard to reach and will lose its performance and

efficiency.

• Ifavailable,alsorefertostovetopmanufacturer’s

height clearance requirements and recommended

hood mounting height above range.

Installation

• This range hood is factory set for venting through the roof or wall.

• Ventworkcanterminateeitherthroughtherooforwall.Toventthroughawall,a90°elbowisneeded.

IMPORTANT:

• NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or

garages. All exhaust must be ducted to the outside.

• Use metal/aluminum duct work only.

• Fasten all connections with sheet metal screws and tape all joints with certied Silver Tape or Duct Tape.

• Use caulking to seal exterior wall or roof opening around the cap.

Duct Run

Calculation

example:

One roof cap, two

90º elbows, and

one 45º elbow use.

0ft + 9ft + 9ft + 5ft

= 23ft used.

Deduct 23ft from

30ft, 7ft maximum

available for

straight duct run.

TOP VENTING

ROOF EXHAUST

TOP VENTING

WALL EXHAUST

REAR VENTING

— 11 —

STEP 7

Remove Accessories

• Unscrew and remove corner bead located underneath the hood

(see Figure 1).

• Unscrew the rectangular damper located underneath the hood,

by removing top screws (see Figure 2).

• Use a tool to punch the wiring hole, from the two options for

holes. Please choose hole A or hole B according to wiring

requirement (see Figure 3).

Installation

STEP 6

Preparations

NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.

• Determine and mark the centre line on the ceiling or wall where the range hood will be installed.

• Make sure there is proper clearance within the ceiling or wall for exhaust vent.

• Duetotheweightandsizeofthisunit,pleasemakesurethatthesupportsystemorframeworkbeingusedisstableand

secure in the ceiling or wall.

• Put a thick, protective covering over countertop, cooktop or range to protect from damage or dirt.

• Removeanyhazardousobjectsaroundtheareawheninstalling.

CAUTION

If moving the cooking range is necessary to install the hood, turn OFF the power on an electric range at the main

electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE.

Figure 1

Figure 2 Figure 3

— 12 —

Installation

Figure 4

Figure 5A Figure 5B

STEP 8 (External Ventilation Only)

Attaching Vent/Damper and Panel Piece

• Depending on the exterior venting option chosen (see page 10), pop

out the steel panel on either the top or rear of the range hood (see

Figure 4).

• Using the supplied screws, attach the rectangular vent/damper on

either the top or rear of the range hood (see Figure 5A or 5B).

• If using top round 6 in. ducting, please purchase Ancona 6” damper (PRH-1275) separately.

• Take out the panel piece from the hardware bag.

• Insert the “panel piece” into the hood as shown on Figure 6.

• For external ventilation, please follow step 8.

• For internal re-circulation, please follow step 9.

Figure 6

— 13 —

STEP 9

Electrical Connection

• Depending if using the wiring hole A or hole B, connect cable to range

hood wiring (see Figure 7).

• Connect BLACK to BLACK, WHITE to WHITE and GREEN to GREEN

(see Figure 8).

• DON’T FORGET TO CONNECT THE GROUND! (green wire)

SAFETY WARNING: Risk of electrical shock. This range hood

must be properly grounded. Make sure this is done by a qualiﬁed

electrician in accordance with all applicable national and local

electrical codes. Before connecting wires, switch power off at service

panel and lock service panel to prevent power from being switched on

accidentally.

Figure 7

Figure 8

IMPORTANT:

• Observeallgoverningcodesandordinances.

• It is the customer’s responsibility to contact a qualified electrical installer.

• Ifcodespermitandaseparategroundwireisused,itisrecommendedthata

qualified electrician determine that the ground path is adequate. A 120-Volt, 60

Hz,AC-only,fusedelectricalsupplyisrequiredonaseparate15-ampcircuit,

fused on both sides of the line.

• DONOTgroundtoagaspipe.

• Checkwithaqualifiedelectricianifyouarenotsurethattherangehoodisproperlygrounded.

• DONOThaveafuseintheneutralorgroundcircuit.

IMPORTANT: Save this Installation Guide for electrical inspector’s use.

GROUNDING INSTRUCTIONS:

• Thisappliancemustbegrounded.Intheeventofanelectricalshort-circuit,groundingreducestheriskofelectric

shock by providing an escape wire for the electric current.

WARNING: Improper grounding can result in a risk of electric shock.

• Consultaqualifiedelectricianifthegroundinginstructionsarenotcompletelyunderstood,orifdoubtexistsasto

whether the appliance is properly grounded. DO NOT use an extension cord. If the power supply cord is too short,

have a qualified electrician install an outlet near the appliance.

• Therangehoodmustbeconnectedwithcopperwire/plugonly.Therangehoodshouldbeconnecteddirectlyto

the fused disconnect (or circuit breaker) box through flexible armored or non-metallic sheathed copper cable. UL/

CSA listed strain relief must be provided at each end of the power supply cable. Use only with range hood cord-

connection kits that have been investigated and found acceptable for use with this model.

Installation

— 14 —

Figure 9

Figure 10

STEP 10A

Wall installation

• Mark or drill a small hole on the mounting position

according to the dimensions on Figure 9.

• Insert suitable screws into the holes.

• Hang the range hood onto the screws.

• For wall installation, please follow step 10A.

• For cabinet installation, please follow step 10B.

STEP 10B

Under the cabinet installation

• Mark or drill a small hole on the mounting position according to the space and dimensions cited on Figure 10.

• Install the hood under the cabinet using suitable screws to x in position.

Installation

27.8” (70.6 cm)

0.81”

(2 cm)

27.8” (70.6 cm)

8.98”

(22.8 cm)

STEP 11 (External Ventilation Only)

Venting

• Depending on exterior ventilation chosen (see page 10), either exit the ducting through the ceiling or wall.

• Alwaysuserigidtypemetal/aluminumducttube(followthebuildingcodesinyourarea)tomaximizeairow.Makesure

thatthebackdraftapscanopen,toallowmaximumairow.Connecttheducttubetothevent/damperandsecurely

seal with certied aluminum or foil tape so that it is airtight. Please check the building codes in your city to learn which

tape product is recommended.

— 15 —

Operation

Speed button Light button

Power

Press on | button for low speed.



Press on || button for high speed.

Press middle O to turn off.

Light

Press button to turn light on and off.

Troubleshooting

Problem Possible Cause

If the range hood or LED light

does not operate after installation:

Check if the range hood has been plugged in, make sure that all power

has been turned back ON, fused not blown and all electrical wiring are

properly connected.

The range hood vibrates when the

blower is on:

The range hood might not have been secured properly on to the ceiling or

wall.

The blower or fan seems weak: Checkthattheductsizedusedisatleast6in.(15.3cm)or31/4×10in.

(8.3 × 25.4 cm). Range hood WILL NOT function efciently with insufcient

ductsize.Forexample:7in.(17.7cm)ductover6in.(15.3cm)holeand

loosely secured.

Checkifductiscloggedorifdamperunit(half-circularange)isnot

installed correctly or opening properly. A tight mesh on a side wall cap unit

mightalsocauserestrictiontotheairow.

The lights work but the fan is not

spinning at all, is stuck or is rattling:

The fan might be jammed or scraping the bottom due to shipping damage.

Please contact us immediately.

The hood is not venting out

properly:

Make sure the distance between the stove top and the bottom of the hood

is within 24 in. and 30 in. (61 and 76.2 cm) in distance.

Reduce the number of elbows and length of duct work. Check if all joints

are properly connected, sealed, and taped.

— 16 —

Proper maintenance of the Range Hood will ensure proper performance of the unit.

Use a warm detergent solution. Grease lters are dishwasher safe.

Stainless steel is one of the easiest materials to keep clean. Occasional care will help preserve its appearance.

Cleaning tips:

• Hot water with soap or detergent is all that is usually required.

• Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks.

• For discolorations or deposits that persist, use a non-scratching household cleanser or stainless steel polishing powder

with a little water and a soft cloth.

• For stubborn cases, use a plastic scouring pad or soft bristle brush with cleanser and water. Rub lightly in direction of

polishing lines or “grain” of the stainless nish. Avoid using too much pressure, which may mar the surface.

• DO NOT allow deposits to remain on surface for long periods of time.

• DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust.

• DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel

for extended periods. Many of these compounds contain chemicals which may be harmful. Rinse with water after

exposure and wipe dry with a clean cloth.

Painted surfaces should be cleaned with warm water and mild detergent only.

Maintenance

Hood Cleaning

Make sure the range hood is unplugged or turn OFF

breaker.

Open the wiring compartment with a Phillips

screwdriver, and unplug the light (Figure 11). Gently

use screwdriver to push down until light pops out

from its location. Pull out the LED light.

CAUTION: LIGHT MAY BE HOT, PLEASE TAKE

OUT THE LIGHT WHEN THE LIGHT IS

COMPLETELY COOL!

Replace with appropriate LED light. Please contact

Ancona customer service for replacement. Plug in

new light and push back into light panel.

Turn ON breaker and range hood to test for

operation.

Replacing the Light

IMPORTANT:

ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY AT THE MAIN PANEL BEFORE CARRYING OUT ANY OPERATION

ON THE APPLIANCE.

Figure 11

— 17 —

Use and Care Information

Operations

• Read and understand all instructions and warnings in this manual before operating the appliance. Save these

instructions for future reference.

• Always leave safety grills and lters in place. Without these components, operating fans could catch on to hair, ngers

and loose clothing.

• NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans.

• NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch re. The risk of self

combustion is higher when the oil has been used several times.

• NEVERcookon“open”amesundertherangehood.Checkdeep-fryersduringuse;superheatedoilmaybe

ammable.

Cleaning

• Thesaturationofgreasyresidueinthefanandltersmaycauseincreasedinammability.Keepunitcleanandfreeof

grease and residue build-up at all times to prevent possible res.

• Filters must be cleaned periodically and free from accumulation of cooking residue (see Cleaning Instructions below).

Old and worn lters must be replaced immediately.

• DO NOT operate fans when lters are removed. Never disassemble parts to clean without proper instructions.

Disassembly is recommended to be performed by qualied personnel only. Read and understand all instructions and

warnings in this manual before proceeding.

SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating!

For optimal operation, clean range hood and all bafﬂe/spacer/ﬁlter/grease tray/oil container regularly. Regular care

will help preserve the appearance of the range hood.

Cleaning Exterior Surfaces

• Clean periodically with hot soapy water and clean cotton cloth. DO NOT use corrosive or abrasive detergent (e.g. Comet

Power Scrub®, EZ-Off® oven cleaner), or steel wool/scoring pads, which will scratch and damage the stainless steel

surface. For heavier soil use liquid degrease such as “Formula 409®” or “Fantastic®” brand cleaner.

• If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting

cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. CAUTION: DO NOT

leave on too long as this may cause damage to hood ﬁnish. Use soft towel to wipe off the cleaning solution, gently

rub off any stubborn spots. Use dry soft towel to dry the hood.

• After cleaning, you may use non-abrasive stainless steel polish such as 3M® or ZEP®, to polish and buff out the

stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.

• DO NOT allow deposits to accumulate or remain on the hood.

• DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.

• DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel

for extended periods. Many of these compounds contain chemicals, which may be harmful.

• Rinse with water after exposure to these compounds and wipe dry with a clean cloth.

— 18 —

MAAN18056SS-01

Please register your product warranty by visiting the Ancona Home website.

Canada & USA

Phone: 1-800-350-4562

Fax: 800-350-8563

Email: [email protected]

Website: www.anconahome.com

Ancona is in association with Mr Appliance for all after sales service calls.

Please contact their service provider or visit their website:

Phone: 1-888-998-2011

Website: www.mrappliance.com

Ancona AN-18056SS 30" 160 CFM Convertible Under Cabinet Range Hood in Stainless steel

Product's Documents

User Manual and Installation Instructions

Specifications

Ancona AN-18056SS Questions and Answers

Related Products

Ancona UCT636 36 in. Under Cabinet Range Hood with Night Light Feature

Ancona AN-1280 UCP430 Under Cabinet Range Hood

Ancona AN-1282 UCC630 Under Cabinet Range Hood

Ancona AN-1229 UC7630 Under Cabinet Range Hood with Night Light Feature 700 CFM 30 in

Ancona AN-1241 UC7636 Under Cabinet Range Hood

Ancona UC64NL 30" Ducted Under-Cabinet Range Hood in Stainless Steel with Night Light Feature