Loading ...
Loading ...
Loading ...
V. INSTRUCTION
Note:
• Position your wine cooler so that the plug is accessible
• Keep your wine cooler out of direct sunlight.
• Do not place next to heat generating appliance.
• Place the wine cooler on a leveled surface that is strong enough to support the unit when it is fully
loaded. To level your wine cooler, adjust the front feet located at the bottom of the unit.
IMPORTANT:
• Position the cooler in a dry and airy place with ambient temperature between 5-32°C (41-90°F).
• Before connecting the unit to a power source, allow it stand upright for approximately 2 hours.
This will reduce the possibility of any system malfunctions which may have occurred from handing
during transportation.
• When positioning the wine cooler, 6 inches of space at the back and 10 inches of space both sides are
suggested. Do not put any objects on top of the unit which may block the air circulation.
POWER CONNECTION:
• This wine cooler should be properly grounded for your safety and in order to minimize the possibility of
electrical shock, the power cord of this unit is equipped with a 3-pin plug which ts with 3-pin wall
outlets.
• Never cut or remove the ground wire from the supplied power cord.
• The use of extension cords is not recommended.
• This unit requires a standard 110V-60Hz electrical outlet with a 3-pin plug.
• The cord should be secured behind the wine cooler. Also, to prevent accidental injury, do not expose or
dangle the cord.
VI. VENTILATION
•
Do not install the wine cooler in a closed cabinet without proper ventilation.
• Please leave at least 6 inches distance between the wall and the wine cooler.
• Do not remove the feet of the wine cooler. Keep at least 50mm of ground clearance.
VII. CLEANING
•
UNPLUG the Wine Chiller, and remove all items including shelves.
• Wash the inside surfaces with a warm water and baking soda solution.
The solution should be about 2 tablespoons of baking soda to a quart of water.
• Wash the shelves with a mild detergent solution.
• Wring excess water out of the sponge or cloth when cleaning area of the controls, or any electrical parts.
• Wash the outside cabinet with warm water and mild liquid detergent.
Rinse well and wipe dry with a clean soft cloth.
www.NutriChefKitchen.com
13
VIII. TROUBLESHOOTING
PROBLEM POSSIBLE CAUSES AND MAINTENANCE MEASURES
The wine cooler will not operate
●
the circuit breaker may be tripped or there is a blown fuse.
The wine cooler is not cold enough
● Check the temperature control settings, as the external
The most ideal ambient temperature for compressor cooling
wine cooler is 5C-32C (41F-90F).
● The door may be opened too frequently.
● The door is not closed completely.
● The door seal does not seal properly.
●
near Heat sink fan on the back within 10cm area.
● The wine cooler includes too much items, as the IT need
some time to cool down and remain stable. Please wait for
24h and check again.
The wine cooler vibrates while
operating
The wine cooler produces
a lot of noise
The wine cooler will not
close properly
The LED display does not work
There is an LED display error
The buttons do not function
Frost or ice developed
inside the wine cooler
● Make sure the unit is leveled.
Please adjust the foot if necessary
● The unit may not be leveled.
● Check the fan, as noise will increasing if your wine cooler
have much dust on the fan after using for a long time.
Please use hair dryer and set strong position to blow away
dust on the fan.
● The unit may not be leveled.
● The doors are reversed and not properly installed.
● The seal is weak.
● There may be a problem with the main control board.
● There is a problem with the plug. Please check to assure
plug is be in good connection with socket or already
plugged in.
● The digital control panel will lock automatically after
10 seconds if no further operation Please press the
unlock button to activate the wine cooler.
● There is a PCB problem.
● The temperature control panel may be damaged.
● Ambient temperature too low.
● The wine cooler needed to be restarted
Loading ...