Loading ...
Loading ...
Loading ...
11
Vacuuming
Figure
Adjust the adjustable floor tool:
䡲
Rugs and carpets =>
䡲
Hard floors/parquet =>
Caution!
Floor tools are subject to a certain amount of wear,
depending on the type of hard floors you have
(e.g. rough, rustic tiles). Therefore, you must check
the underside of the floor tool at regular intervals.
Worn undersides of floor tools may have sharp edges
that can damage sensitive hard floors, such as parquet
or linoleum. The manufacturer does not accept any
responsibility for damage caused by worn floor tools.
Figure Vacuuming with accessories
Attach the nozzles to the tube or handle as required:
a) Crevice nozzle for vacuuming crevices and corners, etc.
b) Upholstery nozzle for vacuuming upholstered furniture,
curtains, etc.
c) Hard furnishing brush
For cleaning window frames, cabinets, mouldings, etc.
d) Hard-floor brush*
For vacuuming hard floors (parquet flooring, laminate
flooring, wooden floorboards, stone floors, etc.)
Figure
Pet hair upholstery nozzle
䡲
For easy and thorough removal of pet hair (attach to
handle or suction pipe as required).
䡲
To clean the pet hair upholstery nozzle, simply vacuum
using the handle.
䡲
If it is very dirty, the pet hair upholstery nozzle can also
be opened.
To do this, turn the two screws on the sides of the nozzle
(e.g. using a coin) and remove the inner part from the
nozzle.
䡲
After cleaning, replace the inner part (make sure it is
correctly seated) and screw to the housing.
Figure
You can use the parking aid on the back of the vacuum
cleaner if you wish to stop vacuuming for a short time.
Once you have switched off the vacuum cleaner, slide
the catch on the floor tool into the groove at the rear of
the appliance.
Figure
To store or transport the vacuum cleaner, use the storage
aid on the underside of the vacuum cleaner.
Stand the vacuum cleaner up on its end. Slide the catch
on the floor tool into the groove on the underside of the
appliance.
!
CAUTION:
Do not operate in an upright/vertical
position.
13
12
11*
10*
9
Figure
The appliance can also be carried using the carrying
handle when vacuuming steps, for example.
When the work is done
Figure
Unplug the vacuum cleaner.
Tug the power cord briefly and let go. The cable then
rewinds automatically.
Figure
Unlock the telescopic tube by moving the sliding button
in the direction of the arrow and slide one tube into the
other.
Emptying the dust container and
cleaning the particle filter
To achieve optimum vacuuming results, the dust container
should be emptied each time the vacuum cleaner is used
or, at the latest, when the maximum fill level is reached. You
should also check the fluff filter, foam filter and motor
protection filter after each vacuuming job. Clean the filters if
necessary, by tapping out the dust or rinsing them.
Emptying the dust container
Figure
Use the release button to unlock the cylinder. The
cylinder releases upwards.
Figure
Remove the dust container from the vacuum cleaner
using the handle.
Figure
Press the button (PRESS) to release the dust container
flap and empty the container into the rubbish bin.
Emptying the dust container
Figure
䡲
Close the dust container flap and click it into place at all
3 catches.
Cleaning the foam filter and fluff filter
Figure
䡲
Open the filter cartridge and take out the filter frame with
the fluff filter and foam filter.
䡲
Remove the fluff filter and foam filter from the filter frame
and clean them by tapping out the dirt. If the filters are
very dirty, they should both be rinsed out. The
components of the fine-dust filter system can be cleaned
in a washing machine at 30 °C using the delicates cycle.
䡲
Insert the foam filter into the fluff filter and clip into the
filter frame.
21
20
19
18
17
16
15
14
*
Depending on equipment
en
Loading ...
Loading ...
Loading ...