F-4N1U-3
F-4N1J-3
F-4N1L-3
The Emerson logo is a trademark and a service mark of Emerson Electric Co.
InSinkErator may make improvements and/or changes in the specifications at any time, in its sole discretion,
without notice or obligation, and further reserves the right to change or discontinue models.
©2020 InSinkErator, InSinkErator a business unit of Emerson Electric Co. All Rights Reserved.
45585-ISE REV A
Installation, Care & Use
ALL-IN-ONE TAP
Multitap -
4N1 Touch
Parex Industries Ltd.
5 Tolich Place, Henderson
Auckland, New Zealand 0610
Sales/Service Tel: 0800 200 510
Email: [email protected]
www.insinkerator.co.nz
InSinkErator
471 Mountain Highway
Bayswater Vic 3153, Australia
Sales/Service Tel: 1300 136 205
Email: [email protected]
www.insinkerator.com.au
InSinkErator
Emerson Electric Co.
1250 International Drive
Mount Pleasant, WI. 53177
USA
Sales/Service Tel: 800-558-5700
www.insinkerator.com
HOT! This system can dispense near boiling water. Care and
supervision should be taken to avoid scalding.
CAUTION
!
F-4N1U-3
F-4N1J-3
F-4N1L-3
The Emerson logo is a trademark and a service mark of Emerson Electric Co.
InSinkErator may make improvements and/or changes in the specifications at any time, in its sole discretion,
without notice or obligation, and further reserves the right to change or discontinue models.
©2020 InSinkErator, InSinkErator a business unit of Emerson Electric Co. All Rights Reserved.
45585-ISE REV A
Installation, Care & Use
ALL-IN-ONE TAP
Multitap -
4N1 Touch
Parex Industries Ltd.
5 Tolich Place, Henderson
Auckland, New Zealand 0610
Sales/Service Tel: 0800 200 510
Email: [email protected]
www.insinkerator.co.nz
InSinkErator
471 Mountain Highway
Bayswater Vic 3153, Australia
Sales/Service Tel: 1300 136 205
Email: [email protected]
www.insinkerator.com.au
InSinkErator
Emerson Electric Co.
1250 International Drive
Mount Pleasant, WI. 53177
USA
Sales/Service Tel: 800-558-5700
www.insinkerator.com
HOT! This system can dispense near boiling water. Care and
supervision should be taken to avoid scalding.
CAUTION
!
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
Notice is used to address practices not related to
personal injury.
NOTICE
!
!
WARNING: To reduce the risk associated with choking: Do
not allow children under 3 years of age to have access to
small parts during the installation of this product.
WARNING: Electric Shock Hazard. To reduce the risk
of electric shock, do not immerse or expose the product,
flexible cord or plug to rain, moisture or any liquid or when
standing in or on damp or wet surfaces. If any electrical
product falls into water, UNPLUG it immediately. DO NOT
REACH INTO THE WATER. Important: Prior to reconnecting
to the power supply, the product should be inspected by a
qualified technician.
• Use the water heater only for its intended use as described in
its manual.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without
supervision.
• Do not operate this product if it has been or appears to be
damaged in any manner or after the product malfunctions, or
is dropped. Return the complete product immediately to your
retail dealer for inspection, and if necessary, adjustment or
repair.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
Save these Instructions.
IMPORTANT SAFETY INFORMATION
!
!
WARNING: Personal Injury/Property Damage. To reduce
the risk associated with hazardous voltage due to an
installer drilling through existing electric wiring in the area
of installation: Do not install near electric wiring or water
pipes which may be in path of a drilling tool when selecting
the position to mount the system bracket.
WARNING: Electric Shock Hazard Using an ungrounded
(no earth ground) or improperly connected appliance can
result in serious injury or death from electrical shock.
Important: Always arrange the power cord so that it cannot come in
contact with hot surfaces.
• Do not disconnect the product from the power supply by pulling on
the cord.
• The use of accessory attachments other than those recommended
by the manufacturer may cause safety hazards.
!
*
!
!
!
!
!
CAUTION: Personal Injury/Property Damage. This tank is
a non-pressurised tank. DO NOT modify this system. DO NOT
close vent tube or connect other types of taps or valves to
the tank. Use only the InSinkErator tap supplied. Use only
parts provided. Contact an authorised InSinkErator Service
agent for repairs or replacement components.
CAUTION: Personal Injury. If hot water discharges from the
tap while not in use , lower the water temperature of the hot
water tank. If the discharge should then continue, turnoff
and unplug the tank.
NOTICE: Property Damage. To reduce the risk associated
with property damage due to water leakage or flooding, and
to ensure optimal performance:
WARNING: To reduce the risk associated with the
ingestion of contaminants: Do not use with water that is
microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
WARNING: Fire Hazard. To minimise possibility of fire, DO
NOT store flammable items such as rags, paper or aerosol
cans near the tank. DO NOT store or use petrol or other
flammable vapours and liquids in the vicinity of this or any
other appliance.
WARNING: Leak Hazard. Regularly inspect tap and
plumbing fittings for leaks, which can cause property
damage and could result in personal injury.
• Read and follow all instructions before installation and
use of this system.
• Installation and use MUST comply with all state and local
plumbing codes.
This appliance must be earthed (grounded). This steaming
hot water tank is equipped with a cord that has a grounding
conductor and earth ground pin. The plug must be connected
to an appropriate outlet that is properly installed and earthed
(grounded) in accordance with all local codes and ordinances.
Do not modify the plug provided with the appliance – if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician. Check with a qualified electrician or tradesman if
you are in doubt as to whether the steaming hot water tank is
properly earthed (grounded).
A steaming hot water tank, like any water heater, has a limited
life and will eventually fail. To avoid possible property damage
and personal injury, this steaming hot water tank should be
regularly examined for leakage and/or corrosion and replaced
when necessary. A drain pan, plumbed to an appropriate
drain or outfitted with a leak detector, should be used in those
applications where any leakage could cause property damage.
IMPORTANT SAFETY INFORMATION
2 3
• Drill, Dedicated control valve, Phillips screwdriver, Pencil,
Tape measure, Level, Tube Cutter
WHAT YOU NEED TO GET STARTED
Equipment Required:
• Anchors for plasterboard, Basin wrench,
Teflon tape, Hole Saw, Hole Punch
Equipment You May Need:
SYSTEM REQUIREMENTS (HOT WATER TANK, FILTRATION SYSTEM AND TAP):
ADDITIONAL CONSIDERATION WHEN UTILISING FILTRATION SYSTEM:
• Make sure that all electrical, plumbing and connections conform to local codes.
• A standard, earthed (grounded) electrical outlet, with continuous supplied power, is required under the sink for the tank.
• This outlet must be fused and should not be controlled by the same wall switch that operates the disposer, unless you have a
SinkTop Switch™ from InSinkErator
®
. Fuse/circuit breaker required is 10 amp for 230 or 220-240 volt and 15 amp for 120 volt.
• In Australia and New Zealand, all plumbing and electrical work must be completed by a qualified tradesperson. The installation
must conform to AS/NZS3500.4 and AS/NZS3000.
• Do not install the filter on hot water supply lines. The maximum operating water temperature of this system is 38°C (100°F).
Attach the filter to the cold water supply only.
• The hot water supply should not exceed 65ºC (149ºF)
• It is recommended that a dedicated control valve be installed on the cold water line supplying water to the filter system.
• To prevent damage or unit not operating properly, the water pressure must be between 210 kPa –860 kPa (2.1 bar - 8.6 bar; 30
psi - 125 psi). Ambient (room) temperature between 4°C (40°F) and 43°C (110°F).
• Do not install if water pressure exceeds 860 kPa (125 psi). If your water pressure exceeds 550 kPa (80 psi), you must install
a pressure limiting valve. In Australia and New Zealand, a Watermark certified AS/NZS2845.1 350 kPa (50 psi) set pressure
limiting valve and dual check valve must be used.
• The use of a water filter should NOT result in the water pressure dropping below 210 kPa (30 psi).
• Do not install where water hammer conditions occur. If water hammer conditions exist you must install a water hammer
arrester.
• The flexible vent and outlet tubes must be correctly connected to the tap supplied by the manufacturer. They must not be
obstructed or connected to a normal type tap or any other type.
• Protect from freezing, shut off water supply, remove filter cartridge, drain hot water tank and tubing when temperatures are
expected to drop below 4°C (40°F).
• Do not use a torch or other high temperature sources near system, cartridges, plastic fittings or plastic plumbing.
• Do not install near water pipes which will be in path of a drilling tool when selecting the position to mount components.
• Mount system in such a position as to prevent it from being struck by other items used in the area of installation.
• Ensure that the location and fasteners will support the weight of the system when installed and full of water.
• When mounting components, screws provided are for use in wood studs or cabinets only. Use wall anchors (not supplied) for
installation into plasterboard.
• Ensure all tubing and fittings are secure and free of leaks.
• Do not install using rigid piping. System intended for use with plastic water lines (such as PEX tubing, PE tubing, PP tubing).
• Do not install this system if any of the quick connect collets are missing from the filter head or Quick Connectors. Contact an
authorized InSinkErator Service agent if collets are missing from any fittings.
• Important: Do not allow the unit to continuously boil.
• Regularly inspect the system. If there are signs of water leakage, turn off the water supply and contact an authorised
InSinkErator Service agent.
• A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any
leakage could cause property damage.
• If you suspect elevated levels of chlorine in your water, or your water has a rusty appearance before the installation of this unit,
use of our water filtration system is recommended.
• This product contains stainless steel. The manufacturer cannot guarantee against rusty water because of the number of factors
that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty water discharged from the hot
water tap may indicate the need for service or replacement of this product.
• Moving parts inside the tank causing a rattling noise is normal.
• For questions or concerns, please contact an authorised InSinkErator Service agent (see back page for contact information).
• The disposable filter cartridge MUST be replaced every 6 months, at the rated capacity or sooner if a noticeable reduction in
flow rate occurs.
• Failure to replace the disposable filter cartridge at recommended intervals may lead to reduced filter performance and cracks in
the filter housing, causing water leakage or flooding.
• Protect from freezing, remove filter cartridge when temperatures are expected to drop below 4°C (40°F).
• Do not install systems in areas where ambient temperatures may go above 43°C (110°F).
• Do not install in direct sunlight or outdoors.
!
• Please refer to the Installation, Care & Use manual packaged with your hot water tank and filtration system for additional
Important Safety Information and installation instructions.
For your satisfaction and safety, read all instructions, cautions and warnings before installing or using this tap.
• This particular unit is not for commercial/industrial use.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
Notice is used to address practices not related to
personal injury.
NOTICE
!
!
WARNING: To reduce the risk associated with choking: Do
not allow children under 3 years of age to have access to
small parts during the installation of this product.
WARNING: Electric Shock Hazard. To reduce the risk
of electric shock, do not immerse or expose the product,
flexible cord or plug to rain, moisture or any liquid or when
standing in or on damp or wet surfaces. If any electrical
product falls into water, UNPLUG it immediately. DO NOT
REACH INTO THE WATER. Important: Prior to reconnecting
to the power supply, the product should be inspected by a
qualified technician.
• Use the water heater only for its intended use as described in
its manual.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use
of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without
supervision.
• Do not operate this product if it has been or appears to be
damaged in any manner or after the product malfunctions, or
is dropped. Return the complete product immediately to your
retail dealer for inspection, and if necessary, adjustment or
repair.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
Save these Instructions.
IMPORTANT SAFETY INFORMATION
!
!
WARNING: Personal Injury/Property Damage. To reduce
the risk associated with hazardous voltage due to an
installer drilling through existing electric wiring in the area
of installation: Do not install near electric wiring or water
pipes which may be in path of a drilling tool when selecting
the position to mount the system bracket.
WARNING: Electric Shock Hazard Using an ungrounded
(no earth ground) or improperly connected appliance can
result in serious injury or death from electrical shock.
Important: Always arrange the power cord so that it cannot come in
contact with hot surfaces.
• Do not disconnect the product from the power supply by pulling on
the cord.
• The use of accessory attachments other than those recommended
by the manufacturer may cause safety hazards.
!
*
!
!
!
!
!
CAUTION: Personal Injury/Property Damage. This tank is
a non-pressurised tank. DO NOT modify this system. DO NOT
close vent tube or connect other types of taps or valves to
the tank. Use only the InSinkErator tap supplied. Use only
parts provided. Contact an authorised InSinkErator Service
agent for repairs or replacement components.
CAUTION: Personal Injury. If hot water discharges from the
tap while not in use , lower the water temperature of the hot
water tank. If the discharge should then continue, turnoff
and unplug the tank.
NOTICE: Property Damage. To reduce the risk associated
with property damage due to water leakage or flooding, and
to ensure optimal performance:
WARNING: To reduce the risk associated with the
ingestion of contaminants: Do not use with water that is
microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
WARNING: Fire Hazard. To minimise possibility of fire, DO
NOT store flammable items such as rags, paper or aerosol
cans near the tank. DO NOT store or use petrol or other
flammable vapours and liquids in the vicinity of this or any
other appliance.
WARNING: Leak Hazard. Regularly inspect tap and
plumbing fittings for leaks, which can cause property
damage and could result in personal injury.
• Read and follow all instructions before installation and
use of this system.
• Installation and use MUST comply with all state and local
plumbing codes.
This appliance must be earthed (grounded). This steaming
hot water tank is equipped with a cord that has a grounding
conductor and earth ground pin. The plug must be connected
to an appropriate outlet that is properly installed and earthed
(grounded) in accordance with all local codes and ordinances.
Do not modify the plug provided with the appliance – if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician. Check with a qualified electrician or tradesman if
you are in doubt as to whether the steaming hot water tank is
properly earthed (grounded).
A steaming hot water tank, like any water heater, has a limited
life and will eventually fail. To avoid possible property damage
and personal injury, this steaming hot water tank should be
regularly examined for leakage and/or corrosion and replaced
when necessary. A drain pan, plumbed to an appropriate
drain or outfitted with a leak detector, should be used in those
applications where any leakage could cause property damage.
IMPORTANT SAFETY INFORMATION
2 3
• Drill, Dedicated control valve, Phillips screwdriver, Pencil,
Tape measure, Level, Tube Cutter
WHAT YOU NEED TO GET STARTED
Equipment Required:
• Anchors for plasterboard, Basin wrench,
Teflon tape, Hole Saw, Hole Punch
Equipment You May Need:
SYSTEM REQUIREMENTS (HOT WATER TANK, FILTRATION SYSTEM AND TAP):
ADDITIONAL CONSIDERATION WHEN UTILISING FILTRATION SYSTEM:
• Make sure that all electrical, plumbing and connections conform to local codes.
• A standard, earthed (grounded) electrical outlet, with continuous supplied power, is required under the sink for the tank.
• This outlet must be fused and should not be controlled by the same wall switch that operates the disposer, unless you have a
SinkTop Switch™ from InSinkErator
®
. Fuse/circuit breaker required is 10 amp for 230 or 220-240 volt and 15 amp for 120 volt.
• In Australia and New Zealand, all plumbing and electrical work must be completed by a qualified tradesperson. The installation
must conform to AS/NZS3500.4 and AS/NZS3000.
• Do not install the filter on hot water supply lines. The maximum operating water temperature of this system is 38°C (100°F).
Attach the filter to the cold water supply only.
• The hot water supply should not exceed 65ºC (149ºF)
• It is recommended that a dedicated control valve be installed on the cold water line supplying water to the filter system.
• To prevent damage or unit not operating properly, the water pressure must be between 210 kPa –860 kPa (2.1 bar - 8.6 bar; 30
psi - 125 psi). Ambient (room) temperature between 4°C (40°F) and 43°C (110°F).
• Do not install if water pressure exceeds 860 kPa (125 psi). If your water pressure exceeds 550 kPa (80 psi), you must install
a pressure limiting valve. In Australia and New Zealand, a Watermark certified AS/NZS2845.1 350 kPa (50 psi) set pressure
limiting valve and dual check valve must be used.
• The use of a water filter should NOT result in the water pressure dropping below 210 kPa (30 psi).
• Do not install where water hammer conditions occur. If water hammer conditions exist you must install a water hammer
arrester.
• The flexible vent and outlet tubes must be correctly connected to the tap supplied by the manufacturer. They must not be
obstructed or connected to a normal type tap or any other type.
• Protect from freezing, shut off water supply, remove filter cartridge, drain hot water tank and tubing when temperatures are
expected to drop below 4°C (40°F).
• Do not use a torch or other high temperature sources near system, cartridges, plastic fittings or plastic plumbing.
• Do not install near water pipes which will be in path of a drilling tool when selecting the position to mount components.
• Mount system in such a position as to prevent it from being struck by other items used in the area of installation.
• Ensure that the location and fasteners will support the weight of the system when installed and full of water.
• When mounting components, screws provided are for use in wood studs or cabinets only. Use wall anchors (not supplied) for
installation into plasterboard.
• Ensure all tubing and fittings are secure and free of leaks.
• Do not install using rigid piping. System intended for use with plastic water lines (such as PEX tubing, PE tubing, PP tubing).
• Do not install this system if any of the quick connect collets are missing from the filter head or Quick Connectors. Contact an
authorized InSinkErator Service agent if collets are missing from any fittings.
• Important: Do not allow the unit to continuously boil.
• Regularly inspect the system. If there are signs of water leakage, turn off the water supply and contact an authorised
InSinkErator Service agent.
• A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any
leakage could cause property damage.
• If you suspect elevated levels of chlorine in your water, or your water has a rusty appearance before the installation of this unit,
use of our water filtration system is recommended.
• This product contains stainless steel. The manufacturer cannot guarantee against rusty water because of the number of factors
that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty water discharged from the hot
water tap may indicate the need for service or replacement of this product.
• Moving parts inside the tank causing a rattling noise is normal.
• For questions or concerns, please contact an authorised InSinkErator Service agent (see back page for contact information).
• The disposable filter cartridge MUST be replaced every 6 months, at the rated capacity or sooner if a noticeable reduction in
flow rate occurs.
• Failure to replace the disposable filter cartridge at recommended intervals may lead to reduced filter performance and cracks in
the filter housing, causing water leakage or flooding.
• Protect from freezing, remove filter cartridge when temperatures are expected to drop below 4°C (40°F).
• Do not install systems in areas where ambient temperatures may go above 43°C (110°F).
• Do not install in direct sunlight or outdoors.
!
• Please refer to the Installation, Care & Use manual packaged with your hot water tank and filtration system for additional
Important Safety Information and installation instructions.
For your satisfaction and safety, read all instructions, cautions and warnings before installing or using this tap.
• This particular unit is not for commercial/industrial use.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
Tap Components
13
14
11
12
15
16
20
18
19
17
22
21
4
6
5
2
3
8
9
10
7
1
B
A
OUT
IN
23 24
25
26
28
27
+
29
1. Tap
2. Main Tap Cold/Hot Water Inlet Tubes
3. Short Copper Tube - Not Labeled
4. Wire From Tap to Solenoid Valve
5. Wire From Tap to Battery
6. Clear Vent Tube
7. Copper Tubes Labeled A and B
8. White Aspirator Tube
9. Tank Outlet Tube with Check Valve
10. Plastic Tube, 1.2 M (47") Long
11. Small Rubber O-Ring
12. Plastic Brace
13. Large Rubber O-Ring
14. Metal Ring
15. Mounting Ring
16. Mounting Screws (3)
17. Mounting Screws for Solenoid Valve Assembly (4)
18. Union Quick Connect
19. “T” Fitting - Quick Connect
20. Solenoid Valve Assembly
21. 9-Volt Alkaline Battery
22. Battery Case and Wire Connection
23. Hot Water Tank
24. Filter Head and Cartridge
25. Y - Quick Connector and Plug
26. Mounting Screws For Tank and Filter (4)
27. Connector 12.7 mm to 9.5 mm (1/2" to 3/8")
28. Pressure Limiter & Back Flow Preventor
29. Filter Tubes (2)
PARTS
Hot Water Tank and Filtration Components
4 5
IMPORTANT INSTALLATION INFORMATION
Notice Property Damage: Before installing this system be aware of the following requirements to avoid water leakage which could
cause property damage. After completing installation check the system to ensure these requirements are complied with.
Braided Tubes:
Quick Connections:
Plastic Tubing:
Maintain a minimum
tube bend of = 2.4” (60mm)
Ensure that the tubes are straight
near the quick connections. Avoid
side loading the quick connection.
Ensure that the tube is pushed all
the way into the quick connection.
Ensure tube is not kinked
or damaged.
Keep the tube straight near its
connection for 3/4” (19 mm)
Do not stretch the tubing to
make the connection
Regularly inspect all quick connections for leaks.
Turn off the water supply immediately if a leak
is detected or the connector appears damaged.
Replace the quick connector before turning the
water back on.
If cleaning any of the connection or tubing, use
only water.
1/4” OD Tubing: Minimum is 1” (25.4 mm)
3/8 OD Tubing: Minimum is 1.25” (31.8 mm)
Ensure the plastic tube with the
quick connection that is attached
to the hot water tank is straight for
1” (25.4 mm) above the connection.
ø min.
ø min.
X
Tap Components
13
14
11
12
15
16
20
18
19
17
22
21
4
6
5
2
3
8
9
10
7
1
B
A
OUT
IN
23 24
25
26
28
27
+
29
1. Tap
2. Main Tap Cold/Hot Water Inlet Tubes
3. Short Copper Tube - Not Labeled
4. Wire From Tap to Solenoid Valve
5. Wire From Tap to Battery
6. Clear Vent Tube
7. Copper Tubes Labeled A and B
8. White Aspirator Tube
9. Tank Outlet Tube with Check Valve
10. Plastic Tube, 1.2 M (47") Long
11. Small Rubber O-Ring
12. Plastic Brace
13. Large Rubber O-Ring
14. Metal Ring
15. Mounting Ring
16. Mounting Screws (3)
17. Mounting Screws for Solenoid Valve Assembly (4)
18. Union Quick Connect
19. “T” Fitting - Quick Connect
20. Solenoid Valve Assembly
21. 9-Volt Alkaline Battery
22. Battery Case and Wire Connection
23. Hot Water Tank
24. Filter Head and Cartridge
25. Y - Quick Connector and Plug
26. Mounting Screws For Tank and Filter (4)
27. Connector 12.7 mm to 9.5 mm (1/2" to 3/8")
28. Pressure Limiter & Back Flow Preventor
29. Filter Tubes (2)
PARTS
Hot Water Tank and Filtration Components
4 5
IMPORTANT INSTALLATION INFORMATION
Notice Property Damage: Before installing this system be aware of the following requirements to avoid water leakage which could
cause property damage. After completing installation check the system to ensure these requirements are complied with.
Braided Tubes:
Quick Connections:
Plastic Tubing:
Maintain a minimum
tube bend of = 2.4” (60mm)
Ensure that the tubes are straight
near the quick connections. Avoid
side loading the quick connection.
Ensure that the tube is pushed all
the way into the quick connection.
Ensure tube is not kinked
or damaged.
Keep the tube straight near its
connection for 3/4” (19 mm)
Do not stretch the tubing to
make the connection
Regularly inspect all quick connections for leaks.
Turn off the water supply immediately if a leak
is detected or the connector appears damaged.
Replace the quick connector before turning the
water back on.
If cleaning any of the connection or tubing, use
only water.
1/4” OD Tubing: Minimum is 1” (25.4 mm)
3/8 OD Tubing: Minimum is 1.25” (31.8 mm)
Ensure the plastic tube with the
quick connection that is attached
to the hot water tank is straight for
1” (25.4 mm) above the connection.
ø min.
ø min.
X
60
30
5
30
55
1050
2040
2535
1545
HOT FILTERED HANDLE
FILTERED COOL WATER TOUCH BUTTON
HOW TO PROPERLY OPERATE THIS TAP
TEMPERATURE CONTROL FLOW CONTROL
MIXING HANDLE
6 7
Note: Do not allow the handle to spring back quickly
Note: Low Battery Indicator: flash (blue green flash). Note: Touch the button to shut off the water flow.
Note: Water flow will automatically stop after approximately 30 seconds.
Note: Dead battery disables manual and auto shut off.
1
2
OUT
IN
B
B
Overview of Complete Setup
60
30
5
30
55
1050
2040
2535
1545
HOT FILTERED HANDLE
FILTERED COOL WATER TOUCH BUTTON
HOW TO PROPERLY OPERATE THIS TAP
TEMPERATURE CONTROL FLOW CONTROL
MIXING HANDLE
6 7
Note: Do not allow the handle to spring back quickly
Note: Low Battery Indicator: flash (blue green flash). Note: Touch the button to shut off the water flow.
Note: Water flow will automatically stop after approximately 30 seconds.
Note: Dead battery disables manual and auto shut off.
1
2
OUT
IN
B
B
Overview of Complete Setup
11
2
NOTICE:
Property Damage. Do not pinch or break copper tubing. Do not distort
the last 35 mm (1") of tubing.
Note: Required 33.5 mm (1
3
/
8") hole size. For ease of installation, insert the
braided hoses through first
*
1
2
15
16
16
12
13
14
x2
11
16
16
15
16
3
6.4mm
(¼")
½
8
9
6
!
8
9
7
WARNING. (Personal Injury) Do not locate filter above an outlet or other
electrical device. Install head and bracket so that connections require no
stretching, kinking or pinching of tubing.
!
NOTICE:
Property Damage. Pinched or blocked water lines may cause damage
to the water tank. Check to make sure tubes are connected correctly and are
pushed down as far as possible.
*
8 9
Note: For best performance minimise the length of the silicon tubes. Cut tubes
must be straight and free of any defects that could cause a leak.
Note: For ease of installation, insert the braided hoses through each
mounting piece first, then the tube and wires.
Note: Turn screws into pre-drilled holes, leaving 1/4" exposed. Tighten the
screws with only 1/2 turn clockwise.
NOTICE:
Property Damage. Do not plug in hot water tank. Tank must be
located within 600 mm (23
1
/
2") of tap and within 76 0mm (30") or less of a
standard earth (grounded) outlet. DO NOT extend plumbing or electrical lines.
*
NOTICE: Property Damage. Item 9 is a brass check valve with attached
silicon tube. The check valve must always be installed to prevent damage to
the hot water tank
*
B
A
B
8
18
10
A
3
9
19
Check Valve
4
< 600 mm (23
1
/
2")
!
*
≤ 760 mm (30")
5
3mm
(¼")
8
6
INSTALLATION
3mm
(¼")
8
6.4mm
(¼")
10 11
12
11
2
NOTICE:
Property Damage. Do not pinch or break copper tubing. Do not distort
the last 35 mm (1") of tubing.
Note: Required 33.5 mm (1
3
/
8") hole size. For ease of installation, insert the
braided hoses through first
*
1
2
15
16
16
12
13
14
x2
11
16
16
15
16
3
6.4mm
(¼")
½
8
9
6
!
8
9
7
WARNING. (Personal Injury) Do not locate filter above an outlet or other
electrical device. Install head and bracket so that connections require no
stretching, kinking or pinching of tubing.
!
NOTICE:
Property Damage. Pinched or blocked water lines may cause damage
to the water tank. Check to make sure tubes are connected correctly and are
pushed down as far as possible.
*
8 9
Note: For best performance minimise the length of the silicon tubes. Cut tubes
must be straight and free of any defects that could cause a leak.
Note: For ease of installation, insert the braided hoses through each
mounting piece first, then the tube and wires.
Note: Turn screws into pre-drilled holes, leaving 1/4" exposed. Tighten the
screws with only 1/2 turn clockwise.
NOTICE:
Property Damage. Do not plug in hot water tank. Tank must be
located within 600 mm (23
1
/
2") of tap and within 76 0mm (30") or less of a
standard earth (grounded) outlet. DO NOT extend plumbing or electrical lines.
*
NOTICE: Property Damage. Item 9 is a brass check valve with attached
silicon tube. The check valve must always be installed to prevent damage to
the hot water tank
*
B
A
B
8
18
10
A
3
9
19
Check Valve
4
< 600 mm (23
1
/
2")
!
*
≤ 760 mm (30")
5
3mm
(¼")
8
6
INSTALLATION
3mm
(¼")
8
6.4mm
(¼")
10 11
12
15.9mm
(5/8")
15.9mm
(5/8")
29
29
!
*
13 14
15
OUT
IN
19
B
OUT
B
10
19
A
18
10
20
21
10 11
Note. For all quick connections in all installation steps, tubes must be FULLY
inserted into the quick connect fitting. Inspect for leaks when water is turned on.
Note: The solenoid valve must attach to the wire (4) from the tap with the male
connection. Do not install the solenoid valve to the battery case. Doing so will
drain the battery.
NOTICE:
Property Damage. Top surface of cartridge will be flush with
bottom of filter head when fully engaged.
*
25
29
!
*
3mm
(¼")
8
OUT
IN
20
16 17
18
NOTICE
: Property Damage. Do not extend the lines farther than the
400 mm (16") provided. Ensure tube and “Y” connector fit securely.
*
Note. It may be desirable to shorten this tube depending on the final position
of downstream components.
Note. To prevent leaks, all cuts in all tubes must be straight and free of defects.
OUT
IN
10
B
OUT
IN
4
B
21
22
22 24
23
15.9mm
(5/8")
15.9mm
(5/8")
29
29
!
*
13 14
15
OUT
IN
19
B
OUT
B
10
19
A
18
10
20
21
10 11
Note. For all quick connections in all installation steps, tubes must be FULLY
inserted into the quick connect fitting. Inspect for leaks when water is turned on.
Note: The solenoid valve must attach to the wire (4) from the tap with the male
connection. Do not install the solenoid valve to the battery case. Doing so will
drain the battery.
NOTICE:
Property Damage. Top surface of cartridge will be flush with
bottom of filter head when fully engaged.
*
25
29
!
*
3mm
(¼")
8
OUT
IN
20
16 17
18
NOTICE
: Property Damage. Do not extend the lines farther than the
400 mm (16") provided. Ensure tube and “Y” connector fit securely.
*
Note. It may be desirable to shorten this tube depending on the final position
of downstream components.
Note. To prevent leaks, all cuts in all tubes must be straight and free of defects.
OUT
IN
10
B
OUT
IN
4
B
21
22
22 24
23
5
12
6
1
3
11
210
48
57
39
45˚
Note: Water will be cold at first. Allow 12-15 minutes for water to reach target
temperature. Gurgling or hissing is normal during the initial heating cycle.
!
12
6
1
2
11
210
48
57
39
!
*
NOTICE:
Property Damage. Do not use an extension lead with the tap. (A standard
earthed outlet within 760 mm (30") of the tap is required under the sink.)
*
WARNING: Scalding Hazard. The tap dispenses near-boiling water which
can instantly cause scalds or burns. Use care when operating this appliance.
Make sure that the handle moves back to the closed position before crossing
the water flow path.
!
12 13
30
31
25 26
32
MOUNTING WITH SCREWS
MOUNTING WITH SELF ADHESIVE
B
B
2728
!
*
2
2
NOTICE:
Property Damage. Tube runs need to form to the cabinet’s contours to
allow storage space with no sharp bends. Tubes need clean, perpendicular, burr-
free cuts to ensure a true fit. Join remaining tube to cold water supply only.
*
Note: Check all connections to ensure they are tight and that there are no leaks.
27 28
29
5
12
6
1
3
11
210
48
57
39
45˚
Note: Water will be cold at first. Allow 12-15 minutes for water to reach target
temperature. Gurgling or hissing is normal during the initial heating cycle.
!
12
6
1
2
11
210
48
57
39
!
*
NOTICE:
Property Damage. Do not use an extension lead with the tap. (A standard
earthed outlet within 760 mm (30") of the tap is required under the sink.)
*
WARNING: Scalding Hazard. The tap dispenses near-boiling water which
can instantly cause scalds or burns. Use care when operating this appliance.
Make sure that the handle moves back to the closed position before crossing
the water flow path.
!
12 13
30
31
25 26
32
MOUNTING WITH SCREWS
MOUNTING WITH SELF ADHESIVE
B
B
2728
!
*
2
2
NOTICE:
Property Damage. Tube runs need to form to the cabinet’s contours to
allow storage space with no sharp bends. Tubes need clean, perpendicular, burr-
free cuts to ensure a true fit. Join remaining tube to cold water supply only.
*
Note: Check all connections to ensure they are tight and that there are no leaks.
27 28
29
!
5-YEAR IN-HOME FULL SERVICE LIMITED WARRANTY
CLEANING THE TAP
CAUTION: PERSONAL INJURY
NOTICE
• Regularly inspect the unit for any signs of leakage. If there are signs of water damage, immediately remove the unit from service.
• An instant hot water dispenser, like any water heater, has a limited life and will eventually fail. To avoid possible property
damage, the instant hot water dispenser should be regularly examined for leakage and replaced when necessary.
A drainage pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications
where any leakage could cause property damage.
• Use only mild cleaners to clean the tap and
plastic components.
• Cleaners with acids, abrasives, alkaline or organic solvents
will result in deterioration of the plastic components and
void the warranty.
• Regularly check for signs of corrosion by examining the
appearance of the dispensed water.
• If the water discolouration remains after draining and
refilling the unit, discontinue use and contact an authorised
InSinkErator service agent.
CARE AND USE
CAUTION: Electric Shock Hazard. To prevent electrical shock, disconnect power before servicing unit. Use only a
properly earthed and polarised electric outlet.
This limited warranty is provided by InSinkErator, a business unit of Emerson Electric Co., (“InSinkErator” or “Manufacturer” or
“we” or “our” or “us”) to the original consumer owner of the InSinkErator product with which this limited warranty is provided
(the “InSinkErator Product”), and any subsequent owner of the residence in which the InSinkErator Product was originally
installed (“Customer” or “you” or “your”).
InSinkErator warrants to Customer that your InSinkErator Product will be free from defects in materials and workmanship, subject
to the exclusions described below, for the “Warranty Period”, commencing on the later of: (a) the date your InSinkErator Product
is originally installed, (b) the date of purchase, or (c) the date of manufacture as identified by your InSinkErator Product serial
number. You will be required to show written documentation supporting (a) or (b). If you are unable to provide documentation
supporting either (a) or (b), the Warranty Period commencement date will be determined by Manufacturer, in its sole and absolute
discretion, based upon your InSinkErator Product serial number.
Permitted Uses
You may use your InSinkErator Product hot/cold water tank and filter system in combination with any genuine InSinkErator
Product tap and component parts and/or Authorized OEM Products. “Authorized OEM Products” mean those hot or hot/cold
water taps and component parts that have been manufactured by an authorized InSinkErator original equipment manufacturer
(“Authorized OEM”) and which have documentation expressly stating that such Authorized OEM Products are compatible with
the InSinkErator Product(s). Authorized OEMs may change from time to time. A list of Authorized OEMs is available to you
upon request or at: www.insinkerator.com/oem. Use of your InSinkErator Product in combination with any products other than
Authorized OEM Products will void this warranty.
What is Covered
This limited warranty covers defects in materials or workmanship, subject to the exclusions below, in InSinkErator Products
used by a consumer Customer for residential use only, and includes all replacement parts and labor costs. YOUR SOLE AND
EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE
INSINKERATOR PRODUCT, PROVIDED THAT IF WE DETERMINE IN OUR SOLE DISCRETION THAT NEITHER REMEDY
IS PRACTICABLE, WE MAY PROVIDE YOU A REFUND OF YOUR PURCHASE PRICE OR A CREDIT TOWARDS ANOTHER
INSINKERATOR PRODUCT.
What is not Covered
This limited warranty does not extend to and expressly excludes:
• Battery replacement
• Losses or damages or the inability to operate your InSinkErator Product resulting from conditions beyond the Manufacturer’s
control including, without limitation, accident, alteration, misuse, abuse, neglect, negligence (other than Manufacturer’s),
failure to install, maintain, assemble, or mount the InSinkErator Product in accordance with Manufacturer’s instructions or
local electrical and plumbing codes.
• Wear and tear expected to occur during the normal course of use, including without limitation, cosmetic rust, scratches, dents
or comparable and reasonably expected losses or damages.
• Losses or damages caused by any product or component part used with the InSinkErator Products, including both Authorized
OEM Products and other products and components.
In addition to the above exclusions, this warranty does not apply to InSinkErator Products installed in a commercial or
industrial application.
No Other Express Warranty Applies
This limited warranty is the sole and exclusive warranty provided to the Customer identified above. No other express warranty,
written or verbal, applies. No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any
other warranty on behalf of Manufacturer. The terms of this limited warranty shall not be modified by the Manufacturer, the
original owner, or their respective successors or assigns.
What we will do to Correct Problems
If your InSinkErator Product does not operate in accordance with the documentation provided to you, or you have questions
concerning your InSinkErator Product or how to determine when service is needed please call the toll free InSinkErator Customer
Service (New Zealand: 0800 200 510) or (Australia: 1300 136 205) or visit our website (New Zealand: www.insinkerator.co.nz) or
(Australia: www.insinkerator.com.au). You may also notify us at: Parex Industries Ltd., 5 Tolich Place, Henderson, Auckland, New
Zealand 0610 or InSinkErator, 471 Mountain Highway, Bayswater Vic 3153, Australia
The following information must be provided as part of your warranty claim: your name, address, phone number, your InSinkErator
Product model and serial number, and if necessary, upon request, written confirmation of either: (a) the date shown on your
installation receipt, or (b) the date shown on your purchase receipt.
Manufacturer or its authorized service representative will determine, in its sole and absolute discretion, if your InSinkErator
Product is covered under this warranty. You will be given the contact information for your closest authorized InSinkErator Service
Center. Please contact your InSinkErator Service Center directly to receive in home warranty repair or replacement service. Only
an authorized InSinkErator service representative may provide warranty service. InSinkErator is not responsible for warranty
claims arising from work performed on your InSinkErator Product by anyone other than an authorized InSinkErator
service representative.
If a covered claim is made during the Warranty Period, Manufacturer will, through its authorized service representative, either
repair or replace your InSinkErator Product. Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair
or installation of the replacement InSinkErator Product are provided at no cost to you. Repair or replacement shall be determined
by Manufacturer or its authorized service representative in their sole discretion. All repair and replacement services will be
provided to you at your home. If Manufacturer determines that your InSinkErator Product must be replaced rather than repaired,
the warranty on the replacement InSinkErator Product will be limited to the unexpired term remaining in the original
Warranty Period.
This tap is covered by Manufacturer’s limited warranty. This limited warranty is void if you attempt to repair the InSinkErator
Product. For service information, please contact the Authorised InSinkErator Service Center for your area as identified on back
cover of this manual.
Limitation of Liability
TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR ITS AUTHORIZED SERVICE REPRESENTATIVES
BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS,
WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE INSINKERATOR PRODUCT OR THE
MANUFACTURER’S OR ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE. MANUFACTURER SHALL NOT BE LIABLE FOR
DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF
ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL
MANUFACTURER’S LIABILITY TO YOU EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE INSINKERATOR PRODUCT.
The term “consequential damages” shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use
or revenue, cost of capital or loss or damage to property or equipment.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply
to you. This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state.
14
Water and steam spits
forcefully from spout
without turning on
the tap.
Water taste or odour.
Water is not hot.
New filter does not fit.
Water is too hot or not
hot enough.
Display lights on
front of tank do not
illuminate.
Display light on front of
tank is blinking.
The filter leaks.
Water comes out of the
vent instead of spout.
No water flow or low
water flow.
Water is dripping
from the spout/vent
intermittently.
Water is dripping
from the spout/vent
constantly.
Water discolouration/
rusty appearance.
Divided stream.
• Unit is boiling.
May be normal during initial set-up.
• Filter water flow direction is wrong.
• Filter needs to be flushed out.
• Life of filter has expired.
• The unit is unplugged.
• The electric outlet is inoperative.
• The power button is not on.
• Head and bracket not fully rotated.
• Filter O-ring breach.
• Thermostat is not adjusted to
your needs.
• The unit may not be plugged in.
• The electric outlet is inoperative.
• If two blinks, the unit was powered on
without water in the tank
• If three blinks, unit needs service
• Head and bracket not fully rotated.
• Filter O-ring breach.
• Outlet tube is blocked.
• Life of filter has expired.
• The expansion chamber is not
draining properly due to low water
pressure.
• The spout is blocked.
• Debris in the water line may be in
the tap valve seat, causing a slow
water leak.
• Corrosion of unit.
• Debris in the end piece.
• Depress or twist steaming hot water tap handle to
release some water from the tank.
• Adjust water temperature using digital display up/
down arrows on tank front.
• Remember that at higher altitudes, water boils at
lower temperatures.
• Review filter tube connection instructions.
• Depress or twist the tap and run until the water is cold.
• If there is no change, replace filter cartridge.
• Make sure the unit is connected to a correctly
earthed electric outlet.
• Make sure the circuit breaker or fuses are
functioning correctly.
• Check that the outlet is not switched off.
• Take out the new filter, put in old filter.
• Remove, inspect, reinstall filter cartridge.
• Adjust the thermostat, then depress or twist hot
water tap handle for 20 seconds to bring in fresh
water to be heated at the new setting. Allow 5-7
minutes for water to reach new temperature.
• Make sure that the circuit breaker or fuses are
functioning properly.
• Check that the outlet is not switched off.
• Unplug the tank and repeat steps 29-31
• Contact an Authorised InSinkErator service agent.
• Test unit by reinstalling old filter and rotating to
full stop. Check for leaks.
• Check that outlet tube is not kinked, twisted
or pinched.
• Unscrew spout end piece and clean out any debris.
• Replace filter cartridge. See Care and Use section
of this manual.
• Unplug the unit. If the dripping does not stop after a
few minutes, check the supply valve to ensure that
it is fully open and there are no obstructions in the
water line reducing the pressure below 30 psi (ie, a
poorly mounted saddle valve, a clogged water filter
or a partially opened shut-off valve).
• Unscrew spout end piece and clean out any debris.
• Unscrew spout end piece and clean out any debris.
• Depress or twist hot water tap handle 7-10 times to
flush tap and lines.
• Unplug and drain unit as described in the Care
and Use section of this manual. If the water
discolouration remains after draining and refilling
the unit, discontinue use and contact an authorised
InSinkErator service agent.
• Unscrew spout end piece and clean out any debris.
TROUBLESHOOTING
PROBLEM
PROBLEM
POSSIBLE CAUSE
POSSIBLE CAUSE
WHAT TO DO
WHAT TO DO
FILTRATION ISSUES
!
Battery disposal in
separate collection only.
1
2 3
CLEANING THE AERATOR
NOTICE:
Property Damage. Check tap for proper water flow and for leaks after
installation is completed.
*
Aerator
Metal end piece
NOTICE:
Remove debris and clean with water only.
*
Gasket
!
5-YEAR IN-HOME FULL SERVICE LIMITED WARRANTY
CLEANING THE TAP
CAUTION: PERSONAL INJURY
NOTICE
• Regularly inspect the unit for any signs of leakage. If there are signs of water damage, immediately remove the unit from service.
• An instant hot water dispenser, like any water heater, has a limited life and will eventually fail. To avoid possible property
damage, the instant hot water dispenser should be regularly examined for leakage and replaced when necessary.
A drainage pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications
where any leakage could cause property damage.
• Use only mild cleaners to clean the tap and
plastic components.
• Cleaners with acids, abrasives, alkaline or organic solvents
will result in deterioration of the plastic components and
void the warranty.
• Regularly check for signs of corrosion by examining the
appearance of the dispensed water.
• If the water discolouration remains after draining and
refilling the unit, discontinue use and contact an authorised
InSinkErator service agent.
CARE AND USE
CAUTION: Electric Shock Hazard. To prevent electrical shock, disconnect power before servicing unit. Use only a
properly earthed and polarised electric outlet.
This limited warranty is provided by InSinkErator, a business unit of Emerson Electric Co., (“InSinkErator” or “Manufacturer” or
“we” or “our” or “us”) to the original consumer owner of the InSinkErator product with which this limited warranty is provided
(the “InSinkErator Product”), and any subsequent owner of the residence in which the InSinkErator Product was originally
installed (“Customer” or “you” or “your”).
InSinkErator warrants to Customer that your InSinkErator Product will be free from defects in materials and workmanship, subject
to the exclusions described below, for the “Warranty Period”, commencing on the later of: (a) the date your InSinkErator Product
is originally installed, (b) the date of purchase, or (c) the date of manufacture as identified by your InSinkErator Product serial
number. You will be required to show written documentation supporting (a) or (b). If you are unable to provide documentation
supporting either (a) or (b), the Warranty Period commencement date will be determined by Manufacturer, in its sole and absolute
discretion, based upon your InSinkErator Product serial number.
Permitted Uses
You may use your InSinkErator Product hot/cold water tank and filter system in combination with any genuine InSinkErator
Product tap and component parts and/or Authorized OEM Products. “Authorized OEM Products” mean those hot or hot/cold
water taps and component parts that have been manufactured by an authorized InSinkErator original equipment manufacturer
(“Authorized OEM”) and which have documentation expressly stating that such Authorized OEM Products are compatible with
the InSinkErator Product(s). Authorized OEMs may change from time to time. A list of Authorized OEMs is available to you
upon request or at: www.insinkerator.com/oem. Use of your InSinkErator Product in combination with any products other than
Authorized OEM Products will void this warranty.
What is Covered
This limited warranty covers defects in materials or workmanship, subject to the exclusions below, in InSinkErator Products
used by a consumer Customer for residential use only, and includes all replacement parts and labor costs. YOUR SOLE AND
EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE
INSINKERATOR PRODUCT, PROVIDED THAT IF WE DETERMINE IN OUR SOLE DISCRETION THAT NEITHER REMEDY
IS PRACTICABLE, WE MAY PROVIDE YOU A REFUND OF YOUR PURCHASE PRICE OR A CREDIT TOWARDS ANOTHER
INSINKERATOR PRODUCT.
What is not Covered
This limited warranty does not extend to and expressly excludes:
• Battery replacement
• Losses or damages or the inability to operate your InSinkErator Product resulting from conditions beyond the Manufacturer’s
control including, without limitation, accident, alteration, misuse, abuse, neglect, negligence (other than Manufacturer’s),
failure to install, maintain, assemble, or mount the InSinkErator Product in accordance with Manufacturer’s instructions or
local electrical and plumbing codes.
• Wear and tear expected to occur during the normal course of use, including without limitation, cosmetic rust, scratches, dents
or comparable and reasonably expected losses or damages.
• Losses or damages caused by any product or component part used with the InSinkErator Products, including both Authorized
OEM Products and other products and components.
In addition to the above exclusions, this warranty does not apply to InSinkErator Products installed in a commercial or
industrial application.
No Other Express Warranty Applies
This limited warranty is the sole and exclusive warranty provided to the Customer identified above. No other express warranty,
written or verbal, applies. No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any
other warranty on behalf of Manufacturer. The terms of this limited warranty shall not be modified by the Manufacturer, the
original owner, or their respective successors or assigns.
What we will do to Correct Problems
If your InSinkErator Product does not operate in accordance with the documentation provided to you, or you have questions
concerning your InSinkErator Product or how to determine when service is needed please call the toll free InSinkErator Customer
Service (New Zealand: 0800 200 510) or (Australia: 1300 136 205) or visit our website (New Zealand: www.insinkerator.co.nz) or
(Australia: www.insinkerator.com.au). You may also notify us at: Parex Industries Ltd., 5 Tolich Place, Henderson, Auckland, New
Zealand 0610 or InSinkErator, 471 Mountain Highway, Bayswater Vic 3153, Australia
The following information must be provided as part of your warranty claim: your name, address, phone number, your InSinkErator
Product model and serial number, and if necessary, upon request, written confirmation of either: (a) the date shown on your
installation receipt, or (b) the date shown on your purchase receipt.
Manufacturer or its authorized service representative will determine, in its sole and absolute discretion, if your InSinkErator
Product is covered under this warranty. You will be given the contact information for your closest authorized InSinkErator Service
Center. Please contact your InSinkErator Service Center directly to receive in home warranty repair or replacement service. Only
an authorized InSinkErator service representative may provide warranty service. InSinkErator is not responsible for warranty
claims arising from work performed on your InSinkErator Product by anyone other than an authorized InSinkErator
service representative.
If a covered claim is made during the Warranty Period, Manufacturer will, through its authorized service representative, either
repair or replace your InSinkErator Product. Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair
or installation of the replacement InSinkErator Product are provided at no cost to you. Repair or replacement shall be determined
by Manufacturer or its authorized service representative in their sole discretion. All repair and replacement services will be
provided to you at your home. If Manufacturer determines that your InSinkErator Product must be replaced rather than repaired,
the warranty on the replacement InSinkErator Product will be limited to the unexpired term remaining in the original
Warranty Period.
This tap is covered by Manufacturer’s limited warranty. This limited warranty is void if you attempt to repair the InSinkErator
Product. For service information, please contact the Authorised InSinkErator Service Center for your area as identified on back
cover of this manual.
Limitation of Liability
TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR ITS AUTHORIZED SERVICE REPRESENTATIVES
BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS,
WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE INSINKERATOR PRODUCT OR THE
MANUFACTURER’S OR ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE. MANUFACTURER SHALL NOT BE LIABLE FOR
DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF
ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL
MANUFACTURER’S LIABILITY TO YOU EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE INSINKERATOR PRODUCT.
The term “consequential damages” shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use
or revenue, cost of capital or loss or damage to property or equipment.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply
to you. This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state.
14
Water and steam spits
forcefully from spout
without turning on
the tap.
Water taste or odour.
Water is not hot.
New filter does not fit.
Water is too hot or not
hot enough.
Display lights on
front of tank do not
illuminate.
Display light on front of
tank is blinking.
The filter leaks.
Water comes out of the
vent instead of spout.
No water flow or low
water flow.
Water is dripping
from the spout/vent
intermittently.
Water is dripping
from the spout/vent
constantly.
Water discolouration/
rusty appearance.
Divided stream.
• Unit is boiling.
May be normal during initial set-up.
• Filter water flow direction is wrong.
• Filter needs to be flushed out.
• Life of filter has expired.
• The unit is unplugged.
• The electric outlet is inoperative.
• The power button is not on.
• Head and bracket not fully rotated.
• Filter O-ring breach.
• Thermostat is not adjusted to
your needs.
• The unit may not be plugged in.
• The electric outlet is inoperative.
• If two blinks, the unit was powered on
without water in the tank
• If three blinks, unit needs service
• Head and bracket not fully rotated.
• Filter O-ring breach.
• Outlet tube is blocked.
• Life of filter has expired.
• The expansion chamber is not
draining properly due to low water
pressure.
• The spout is blocked.
• Debris in the water line may be in
the tap valve seat, causing a slow
water leak.
• Corrosion of unit.
• Debris in the end piece.
• Depress or twist steaming hot water tap handle to
release some water from the tank.
• Adjust water temperature using digital display up/
down arrows on tank front.
• Remember that at higher altitudes, water boils at
lower temperatures.
• Review filter tube connection instructions.
• Depress or twist the tap and run until the water is cold.
• If there is no change, replace filter cartridge.
• Make sure the unit is connected to a correctly
earthed electric outlet.
• Make sure the circuit breaker or fuses are
functioning correctly.
• Check that the outlet is not switched off.
• Take out the new filter, put in old filter.
• Remove, inspect, reinstall filter cartridge.
• Adjust the thermostat, then depress or twist hot
water tap handle for 20 seconds to bring in fresh
water to be heated at the new setting. Allow 5-7
minutes for water to reach new temperature.
• Make sure that the circuit breaker or fuses are
functioning properly.
• Check that the outlet is not switched off.
• Unplug the tank and repeat steps 29-31
• Contact an Authorised InSinkErator service agent.
• Test unit by reinstalling old filter and rotating to
full stop. Check for leaks.
• Check that outlet tube is not kinked, twisted
or pinched.
• Unscrew spout end piece and clean out any debris.
• Replace filter cartridge. See Care and Use section
of this manual.
• Unplug the unit. If the dripping does not stop after a
few minutes, check the supply valve to ensure that
it is fully open and there are no obstructions in the
water line reducing the pressure below 30 psi (ie, a
poorly mounted saddle valve, a clogged water filter
or a partially opened shut-off valve).
• Unscrew spout end piece and clean out any debris.
• Unscrew spout end piece and clean out any debris.
• Depress or twist hot water tap handle 7-10 times to
flush tap and lines.
• Unplug and drain unit as described in the Care
and Use section of this manual. If the water
discolouration remains after draining and refilling
the unit, discontinue use and contact an authorised
InSinkErator service agent.
• Unscrew spout end piece and clean out any debris.
TROUBLESHOOTING
PROBLEM
PROBLEM
POSSIBLE CAUSE
POSSIBLE CAUSE
WHAT TO DO
WHAT TO DO
FILTRATION ISSUES
!
Battery disposal in
separate collection only.
1
2 3
CLEANING THE AERATOR
NOTICE:
Property Damage. Check tap for proper water flow and for leaks after
installation is completed.
*
Aerator
Metal end piece
NOTICE:
Remove debris and clean with water only.
*
Gasket
