American Range ARDCT366L Vitesse Series 36 Inch Gas Sealed Burner Cooktop

User Manual - Page 7

For ARDCT366L.

PDF File Manual, 16 pages, Read Online | Download pdf file

ARDCT366L photo
Loading ...
Loading ...
Loading ...
7
4580 N. Walnut Rd., N. Las Vegas, NV 89081
|
13592 Desmond St., Pacoima, CA 91331
|
tel: 818.897.0808
|
888.753.9898
|
www.AmericanRangeHome.com
INSTALLATION
CHECK THAT ALL GAS CONNECTIONS ARE PROPERLY SEALED WITH A SUITABLE GAS JOINT COMPOUND.
TEST ALL JOINTS WITH A SOAPY WATER SOLUTION BEFORE LIGHTING THE BURNERS.
1. Turn ON the manual gas valve at the inlet side of the gas supply line.
2. Check for gas leaks at the exible coupling or gas connector tting using a solution of one part soap and three parts water.
3. Sparingly spray or brush the soapy solution at the gas ttings; active bubbling indicates location of gas leak.
4. If a gas leak is detected turn o the manual gas valve at the inlet side of the gas line. Call your certied service technician.
» Do not remove protective packaging until you are ready to
perform the installation.
» Caution – the appliance is heavy. Use extreme care when
handling!
» Any openings in the wall and in the oor behind or under the
cooktop must be sealed.
» Do not use an extension cord with this appliance. Such use
may result in re, electrical shock or other personal injury.
INSTALLATION
The location selected for the range must meet the following
criteria. If any of these criteria are not met, select another
location.
SITE PREPARATION
» The cooktop is zero-clearance safe against non-combustible
surfaces
» The maximum depth of overhead cabinets installed on either
side of the hood is 13"
» Any openings in the wall behind the range and in the oor
under the range must be sealed
ELECTRICAL CONNECTION
» The cooktop must be electrically grounded in compliance with
local codes or, in the absence of local codes, with the National
Electrical Code, ANSI/NFPA70.
» This cooktop requires a 120 volt supply to operate the ignition
system. The supply cord provided on the range is equipped
with a three-prong (grounding) plug for protection against
electrical shock.
» The electrical service in the building must be equipped with a
properly grounded three-prong receptacle.
» Do not cut or remove grounding prong from this plug.
POWER REQUIREMENTS FOR THIS COOKTOP
» 120 VAC, 60 Hz, single phase, 15 AMP Max
GAS CONNECTION
» Be certain the appliance being installed is correct for the gas
service being provided. Refer to the appliance data plate for the
gas supply requirements.
» A manual gas shut-o valve must be remotely installed and
easily accessible within the cabinet. The regulator inlet is for a
1/2 inch gas line. The appliance ships with a 1/2 inch regulator.
» Use at least a 1/2" commercial ex hose to connect range to
the gas supply (service line).
» A manual gas shut-o valve must be installed, in easy access in
front of the gas supply (service line) and ahead of the cooktop
for safety and ease of maintenance.
» All valves must be in the OFF position before connecting to the
gas supply line.
PRESSURE REGULATOR
» The regulator packed with the cooktop is adjusted at the
factory for 5" WC (natural gas) or 10" WC (L.P.) depending
on the customer’s request. Regulators must be used in the
installation.
» The regulator can withstand a maximum pressure of 1/2 PSIG
(14" WC). If the line pressure is beyond this limit, a step-down
regulator will be required.
» Any adjustment to regulators must be made ONLY BY
QUALIFIED service personnel with proper test equipment.
GAS REQUIREMENTS
» Ensure supplied gas matches the cooktop’s gas type.
» Natural gas connection is 1/2" N.P.T. minimum 1/2" diameter
ex line.
» Natural gas inlet pressure to measure 7" to 10" W.C.
» Propane gas connection is 1/2" N.P.T. minimum 1/2" diameter
ex line.
» LP gas inlet pressure to measure 11" to 14" W.C.
» A step-down regulator in addition to the regulator provided
with the LP range is required at the LP (Propane) source to
limit pressure to a maximum of 14" W.C.
» Installation of this appliance should be performed by qualied,
licensed contractors.
» To remove the packaging, rst remove the staples located at
the bottom perimeter of the corrugated cardboard cover.
» Conrm access to adequate power and gas. See specications
and electrical requirements table.
» Fill out the inside cover of this installation manual with the
requested data. Model Number and Serial Number can
be found on the plate located on the bottom of the chassis.
Loading ...
Loading ...
Loading ...