Loading ...
Loading ...
Loading ...
INSTALLATION
We strongly recommend the removal of the
old wall sleeve and the installationof a new
Kenmore folding Wall Sleeve.
If you decide to keepthe existing wall sleeve,
you have to redirect the louvers at the back of the
wall sleeve illustration. The use of pliers is
recommended. If you DO NOT redirect, yourun
the risk of poor performance or product failure.
This is notcovered under the terms of the
Kenmore warranty.
• Pick a location which will allow the conditioned air to
blow into the area you want. Good installation with
special attention to the proper position of the unit will
lessen the chance that service will be needed.
• Assemble the folding sleeve for this unit according to
the instructions provided.
ITEMS IN INSTALLATION HARDWARE
Youmaynotneedallpartsin thekit,Discardunused
_arts
_e
Horizontal Insulation Strips
Around Insulation Strips
Support Block
Baffle
Shim
Trim Frame
Washer Screw
Nuts(Plastic)
ITEM (inches)
283/4 X 161/2
13/8X 5/8X 273/16
13/8 X 13/8 x 273/16
13/8x 3/4x 611/2
13/8 x 13/8X 611/2
13j4 x 13/8x 45/16
14 x 41/2 X %
13x 1 X3/4
Qty.
1
1
1
1
1
2
1
2
2
4
4
HOW TO INSTALL
a identify the existing wall sleeve before installing
the unit from the listed below.
Brand Wall Sleeve Dimensions (inches
Width Height Depth
White-WestinghousE
Frigidaire 25-1/2 15-1/4 16, 17-1/2
Carrier (52F series) or 22
General Electric
iHotpoint 26 15-5/8 16-7/8
Whirlpool 25-7/8 16-1/2 17-1/8
or 23
Fedders/Emerson 27 16-3/4 16-3/4
or 19-3/4
Sears/Kenmore 25-7/8 15-17/32 16-23/32
Emerson/Fedders 26-3/4 15-3/4 15
Carrier (51S Series) 25-3/4 16-7/8 18-5/8
Friedrich 27 16-3/4 16-3/4
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition
and have a rear grille that securely attaches to
sleeve, or rear flange that serves as a stop for the
Air Conditioner,
I_'_ Remove old air conditioner from existing wall
sleeve.
i_ Clean the interiorof an existing sleeve.
(Do not disturb seals.)
L_Wall sleeve must be securely fastened in wall
before installing the air conditioner. Use the
nails or screws through sleeve into wall, if
needed. Repaint sleeve if needed.
I_ Prepare the wall sleeve for installation of the
unit. If you plan to use your existing wall sleeve,
and it is not Kenmore, use procedure B or C
below.
Procedure
A
B
Brand
Sears/Kenmore
White-Westinghouse
Frigidaire Carrier
(52F series)
General Electric
/Hotpoint
Whirlpool
Carrier (51S series)
Fedders/Emerson
Depth(inches
16-23/32
16, 17-1/2
or 22
16-7/8
C
Emerson/Fedders
Friedrich
r_ Install unit intowall sleeve.
new
CAUTION: When installation is completed,
replacement unit MUST have a rearward slope as
shown.
UNIT Wall Sleeve
17-1/8 or 23
18-6/8
16-3/4
or 19-3/4
15
16-3/4
FRONI_ T-.............
1/4't U] ............
FIG. 2
-6-
Loading ...
Loading ...
Loading ...