USAGE AND
CARE GUIDE
PRODUCT
CODE:
EA60XR
rangehoods
Content
1
3
6
9
9
Safety Instructions
Installation
Start using your Cooker
Hood Troubleshooting
Maintenance and Cleaning
Environmental Protection
13
1
SAFETY INSTRUCTIONS
This manual explains the proper installation and use of your cooker hood, please read it
carefully before using even if you are familiar with the product. The manual should be kept in
a safe place for future reference.
Never to do:
• Do not try
to use the cooker hood
without the grease filters or if the filters
are excessively greasy!
• Do not install above a cooker with a high
level grill.
• Do not leave frying pans unattended
during use because overheated fats or
oils might catch fire.
• Never leave naked flames under the
cooker hood.
• If the cooker hood
is damaged, do not
attempt to use.
• Do not flambé under the cooker hood.
• CAUTION: Accessible parts may
become hot when used with cooking
appliances.
• The minimum distance between the
supporting surface for the cooking
vessels on the hob and the lowest part
of the cooker hood. (When the cooker
hood is located above a gas appliance,
this distance shall be at least 65 cm)
• The air must not be discharged into a
flue that is used for exhausting fumes
from appliances burning gas or other
fuels. Range hoods and other cooking
fume extractors may adversely affect
the safe operation of appliances burning
gas or other fuels (including those in
other rooms) due to back flow of
combustion gases. These gases can
potentially result in carbon monoxide
poisoning.
• After installation of a rangehood or other
cooking fume extractor, the operation of
open flued gas appliances should be
tested by a competent person to ensure
that back flow of combustion gases does
not occur.
Always to do:
• Important! Always switch off
the
electricity supply at the mains during
installation and maintenance such as
light bulb replacement.
• The cooker hood must be installed in
accordance with the installation
instructions and all measurements
followed.
• All installation work must be carried out
by a competent person or qualified
electrician.
• Please dispose of the packing material
carefully. Children are vulnerable to it.
• Pay attention to the sharp edges inside
the cooker hood especially during
installation and cleaning.
• Make sure the ducting has no bends
sharper than 90 degrees as this will
reduce the efficiency of the cooker hood.
• Warning: Failure to install the screws or
fixing device in accordance with these
instructions may result in electrical
hazards.
• Warning: Before obtaining access to
terminals, all supply circuits must be
disconnected.
2
Always to do:
• Always put lids on pots and pans
when cooking on
a gas cooker.
• When in extraction mode, air in the
room is being removed by the cooker
hood. Please make sure that proper
ventilation measures are being
observed. The cooker hood removes
odours from room but not steam.
• There shall be adequate ventilation of
the room when the cooker hood is used
at the same time as appliances burning
gas or other fuels.
• Cooker hood is for domestic use only.
• If the supply cord is
damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
• This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved. Children should not play with
the appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
Al
ways to do:
• Caution: The appliance and its accessible
parts c
an become hot during operation. Be
careful to avoid touching the heating
elements. Children younger than 8 years
old should stay away unless they are under
permanent supervision.
• There is a fire risk if cleaning is not carried
out in accordance with the instructions.
• Regulations concerning the discharge
of air have to be fulfilled.
• Clean your appliance periodically by
following the method given in the chapter
MAINTENANCE.
• For safety reason, please use only the
same size of fixing or mounting screw
which are recommended in this instruction
manual.
• Regarding the details about the method
and frequency of cleaning, please refer
to maintenance and cleaning section in
the instruction manual.
• Cleaning and user maintenance shall not
be made by children without supervision.
• When the cooker hood and appliances
supplied with energy other than electricity
are simultaneously in operation, the
negative pressure in the r
oom must not
exceed 4 Pa(4 x 10
-
5
bar).
• WARNING: Danger of fire: do not store
items on the cooking surfaces.
• A steam c
leaner is not to be used.
• NEVER try to extinguish a fire with water,
but switch off the appliance and then cover
flame e.g. with a lid or a fire blanket.
3
INSTALLATION (VENT OUTSIDE)
MOUNTING OF THE V-FLAP
If the c
ooker hood does not have an assembled V-flap 1, you should mount the half-parts to
its body. The images only show an example of how to mount the V-flap, because the outlet
may vary according to different models and configurations.
To mount the V-flap 1 you should:
• Mount two half-parts 2 into the body 6;
• the pin 3 s
hould be top oriented;
• the axis 4 should be inserted into the holes 5 on the body;
• repeat all the operations for the 2nd half-part.
INSTALLATION
If y
ou have an outlet to the outside, your cooker hood can be connected as below picture
by means of an extraction duct (enamel, aluminum, flexible pipe or non-flammable
material with an interior diameter of 150mm)
1. Before installation, turn the unit off and unplug it from the outlet.
4
2. The cooker hood s
hould be placed at a distance of 65~75cm above the cooking surface
for best effect. See pic 1.
3. Install the hook on a suitable place once the ins
tallation height is fixed, and keep it in line.
The fixed position of the inside chimney bracket is the place of chimney. See pic 2.
4. Fix the outside chimney bracket on the outside chimney, and be sure that the inside
chimney can be adjusted the height in it freely as well as fixing the expansion pipe.
Afterwards, install the expansion pipe and chimney on the cooker hood. Fix the expansion
pipe with the cable tie on the outlet. Note :The expansion pipe is not included in the
product. See pic 3.
5. P
ut the cooker hood on the hook. See pic 4.
6. Adjust the height of the inside chimney to the position of the inside chimney bracket and fix
on it with screws, after adjusting the position, fix the body with safety screws.
Note: The two safety vents are positioned on the back housing, with diameter of 6mm. Lay
the expansion pipe to the wall outlet. See pic 5.
5
HINTS FOR EXHAUST DUCT INSTALLATION
The following r
ules must be strictly followed to obtain optimal air extraction:
• Keep ex
pansion pipe short and straight.
• Do not reduce the size or restrict the expansion pipe.
• When using the expansion pipe always install the pipe pulled taut to minimize pressure
loss.
• Failure to observe these basic instructions will reduce the performance and increase
noise levels of the cooker hood.
• Any installation work must be carried out by a qualified electrician or competent person.
• Do not connect the ducting system of the hood to any existing ventilation system which
is being used for any other appliance ,such as warmer tube, gas tube , hot wind tube.
• The angle of the bend of the expansion pipe should not be less than 120º; you must
direct the pipe horizontally, or, alternatively, the pipe should go up from the initial point
and should be led to an outer wall.
• After the installation ,make sure that the cooker hood is level to avoid grease collection
at on end.
• Ensure the expansion pipe selected for installation complies with relevant standards
and is fire retardant.
WARNING:
For s
afety reason, please use only the same size
of fixing or mounting screws which are
recommended in this instruction manual.
Failure to install the screws or fixing device in
accordance with these instructions may result in
electrical hazards.
6
S
tart Using Your Cooker Hood
Electronic button with LED display
1. Power-on: After connecting the cooker hood to the main supply, the backlight of all
buttons will turn on and the buzzer sounds for once. The LED display is closed .
The cooker hood doesn’t work and enters into stand-by mode.
2. (Lamp) button:
Press
(Lamp) button, the lights will be on. Press again, the lights will be off.
The above steps can be repeated operating. The lamp funtion could be operated
without pressing the
(Power) button.
3. (Power) button:
3.1 Press (Power) button ,the cooker hood starts to work at the low speed
and the LED display will display “1”. Press again, the cooker hood will stop.The
cooker hood speeds can only be adjusted when starting the power button.
3.2 After switching off the speeds of cooker hood by power button, when press
the power button again to start-up the hood, motor will work at the speed before the
last exit.
4.
(Speed) button:
The cooker hood has three speed levels ,they are low,mid,high, and the
corresponding LED display will be”1”,”2”,”3”.
4.1 After switching on the power button,the hood starts to work at low speed and
the LED display will display “1”.
4.2 Press
(Speed) button again when it works at low speed, the cooker hood
works at mid speed and the LED display will display “2”.
4.3 Press (Speed) button again when it works at mid speed, the cooker hood
at the high speed and the LED display will display “3”.
4.4 During the working, you can touch (Speed) button to change the speed
circularly: “low
→
mid
→
high
→
low
→
mid
……
”
5.
(
Timer) button:
7
The tim
er button
is only used for the timer function when the hood is working.
(Press the button will be invalid when the hood is under standby mode or open the
lamp separately).
5.1 Press the timer button, the hood enter into the timer function. The timer setting
is 9mins and the display shows “9”.
5.2 After the timing function starts, the display shows “9”, “8”, “7”..., decreasing by
minute. After the timing is completed, the motor will automatically cut off the power
immediately and the motor output will be turned off. The lights are off at the same
time.
5.3 Press the timer button once to enter the timer function. Press again to exit the
timer function. The above steps can be operated repeatedly. In the timing state,
pressing the speed button will automatically exit the timing function.
Connecting the remote control
• A n
ew remote control has to establish a new connection to the cooker hood
when used for first time. One remote control could possibly control several
cooker hood at the same time.
Connection process between remote control and cooker hood
• Within 15S after the cooker hood
connects to the power supply, long press
for 5 seconds, the indicators light begin flashing from one button to
another ,the cooker hood is in connection mode, press any button on remote
control to confirm the connection. The connection process finished and the
remote control can be used for speed selection, lighting and timer setting.
• If you want to connect again, you will need to clear the code that has been set
up previously.
• To clear the code, press for 5 seconds, the indicators light begin flashing from
one button to another, the cooker is in connection mode. Then, press again
for 5 seconds, the previous connection code is cleared.
• When the previous code has been cleared, the
cooker hood back to standby
mode, press for 5 seconds, the indicate light flashing from one button to
another ,the cooker hood is in connection mode, then, press any button on
remote control to confirm the connection.
8
Remote control
1. Lighting
press button once, the light is on, press again, the light is off.The lighting
button it is controlled separately and will not affect any other functions.
2. Turning on/ Increasing
motor speed button the motor has low, mid and
high levels.
2.1 Press once,the motor will work at low speed (Turning on).
2.2When the hood works at low s
peed,press again, the motor changes
to mid speed.
2.3Base on the middle speed condition, press again, the motor is
running in the high speed.
2.4Base on the high s
peed condition, press again, the hood still works
at high speed.
3. Turning off/Decreasing motor speed key
3.1 press the button and the motor begins shift to a lower speed and the LCD
screen display the speed level. Repeating press
the button, it keep on decreasing
the motor speed till the cooker hood turning off.
4. Low s
peed, mid speed and high speed cannot work at the same time. When hood
is on high speed, press the speed decrease, it will turn to a lower speed; when it is
in low speed, press the speed increase, it will turn to a higher speed.
5. Timer
Press the button to set up the timer on/off function.
9
TROUBLESHOOTING
Fault P
ossible Cause
Solution
Light on, but m
otor
does not work
Fan s
witch turned off
Select a fan switch position.
Fan s
witch failed
Contact s
ervice center.
M
otor failed
Contact s
ervice center.
Light does not
work, m
otor does
not work
House fus
es blown
Reset/Replace fuses.
M
ains power cable is loose or
disconnected
Refit mains power c
able to
power outlet.
Switch power outlet on.
Oil leakage
One way v
alve and the outlet
are not tightly sealed
Tak
e down the one way valve
and seal with sealant.
Leakage from the c
onnection of
chimney and cover
Tak
e chimney down and seal.
Lights not wor
king
Br
oken or faulty bulbs
Replace bulbs as per this
instruction.
Insufficient s
uction
The distance between the
c
ooker hood and the gas top is
too far
Refit the c
ooker hood to the
correct distance.
The Cooker hood
inclines
The fixing s
crew is not tight
enough
Tighten the hanging s
crew and
make it horizontal.
NOTE:
A
ny electrical repairs to this appliance must conform to your local, state and
federal laws. Please contact the service centre if in any doubt before undertaking
any of the above. Always disconnect the unit from the power source when opening
the unit.
M
AINTENANCE AND CLEANING
Caution:
• B
efore maintenance or cleaning is carried out, the cooker hood
should be disconnected from the mains power supply. Ensure
that the cooker hood is switched off at the wall socket and the
plug removed.
• External surfaces are susceptible to scratches and abrasions, so please follow the
cleaning instructions to ensure the best possible result is achieved without damage.
GE
NERAL
Cleaning and maintenance should be carried out with the appliance cold especially
when cleaning.Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.)
on the surfaces.
10
STAINLESS STEEL
The stainless s
teel must be cleaned regularly (e.g.weekly) to ensure a long life
expectancy.Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may
be used.
NOTE:
Ensure that wiping is done along with the grain of the stainless steel to prevent any
unsightly crisscross scratching patterns from appearing.
CONTROL PANEL SURFACE
The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is
clean and well wrung before cleaning. Use a dry soft cloth to remove any excess
moisture left after cleaning.
Important
Using neutral detergents and avoid using harsh cleaning chemicals, strong household
detergents or products containing abrasives, as this will affect the appearance of the
appliance and potentially remove any printing of artwork on the control panel and will
void manufactures warrantee.
GREASE MESH FILTERS
The mesh filters can be cleaned by hand. Soak them for about 3 minutes in water with
a mild detergent and then brush it gently with a soft brush. Do not apply too much
pressure so as to avoid any damage to it . (Leave to dry naturally out of direct sun light)
Filters should be washed separately to crockery and kitchen utensils. It is advisable not
to use rinse aid.
INSTALLING GREASE MESH FILTERS
To install filters for
the following four steps:
• A
ngle the filter into the slots at the back of the hood.
• Push the button on the handle of the filter.
• Release the handle once the filter fits into a resting position.
• Repeat to install all filters.
CARBON FILTER -
not supplied
Activated carbon filter can be used to trap odors. Normally the activated carbon filter
should be changed every 3 to 6 months according to your cooking habits. The
installation procedure of activated carbon filter is as below:
11
1. B
efore installing or replacing the carbon filters, disconnect the mains power
to the unit.
2. Press the filter lock and remove the mesh filter.
3. Turn the carbon filter on both sides of the motor anti-clockwise. Replace the
carbon filters with the new carbon filters.
4. Place the mesh filter.
5. Connect the power supply to the wall socket.
NOTE:
• Make sure the filter is s
ecurely locked. Otherwise, it would loosen and cause
danger.
• When activated carbon filter attached, the suction power will be lowered.
BULB REPLACEMENT
Important
• Always switch of
f the electricity supply before
carrying out any operations on the appliance.
When handling bulb, make sure it has completely
cooled down before any direct contact with hands.
• When handling bulbs hold with a cloth or gloves to
ensure perspiration does not come in contact with
the bulb as this can reduce the life of the bulb.
Note:
• B
efore changing the lights, make sure that the appliance is turned off and
unplugged.
• Protect against danger when changing lights, such as wearing gloves.
Changing t
he lights:
• Rem
ove the grease filter.
• Use a tool or the hand to press the spring splinter of both sides of LED light to the
inside, until the light is pressed out, see pic 1. Then slightly pull the light connecting
wire out, and dismantle the terminal of the light connecting wire. See pic 2.
• Apply the reverse procedure to install the light back.
ILCOS D c
ode for this lamp is: DSR-1.5/65-S-64
• LED modules – r
ound lamp
• Max wattage: 2×1.5 W
• Voltage range: DC 12V
• Dimensions:
13
ENVIRONMENTAL PROTECTION:
This product is marked with the symbol on the s
elective sorting of waste
electronic equipment. This means that this product must not be disposed
of with household waste but must be supported by a system of selective
collection in accordance with Directive 2012/19/EU. It will then be
recycled or dismantled to minimize impacts on the environment,
electrical and electronic products are potentially dangerous for the
environment and human health due to the presence
of hazardous substances. For more information, please contact your
local or regional authorities.
NOTE:
The following shows how to reduce total environmental impact (e.g. energy use) of the
cooking process).
(1) Install the cooker hood in a proper place where there is efficient ventilation.
(2) Clean the cooker hood regularly so as not to block the airway.
(3) Remember to switch off the cooker hood light after cooking.
(4) Remember to switch off the cooker hood after cooking.
INFORMATION FOR DISM
ANTLING
Do not dismantle the appliance in a way which is not shown in the user manual.
The appliance could not be dismantled by user. At the end of life, the appliance
should not be disposed of with household waste. Check with your Local Authority or
retainer for recycling advice.
Pronto Service + Support: 1800 440 335
Email: [email protected]
HEAD OFFICE
65 Glynburn Road, Glynde SA 5070
Ph: 08 8165 1012
www.euroappliances.com.au
