Loading ...
Form No. SJ-BH-318S-880E-M
This information is intended to assist in comparing the relative shock-
absorbing properties of various materials. No particular material is
recommended over another. However, each material is only effective when
maintained. Materials should be checked periodically and replenished to
maintain correct depth as determined necessary for your equipment. The
choice of a material depends on the type and height of the playground
equipment, the availability of the material in. Your area, and its cost.
ADDITIONAL SAFETY TIPS:
• On-site adult supervision is required.
• Teach children not to push empty seats. The seat may hit them and
cause injury.
•
Teach children to sit in the center of swings with their full weight on the seats.
• Teach children to hold on tight and secure feet on footer before
climbing rope.
• Teach children not to climb when the equipment is wet.
• One of the most important things you can do to reduce the likelihood
of serious head injuries is to install shock-absorbing protective
surfacing under and around your play equipment. The protective
surfacing should be applied to a depth that is suitable for the
equipment height in accordance with CPSC. There are different
types of surfacing to choose from; whichever product you select,
please refer to the "Consumer Information Sheet for Playground
Surfacing Materials" section and "TABLE — Depth of Surfacing
Material Required Based On Fall Heights" If any of the following
conditions are noted they should be removed, corrected or repaired
immediately to prevent injuries:
•
Hardware that is loose, or worn, or those that have protrusions or projections.
• Scattered debris, litter, rocks or tree roots.
• Missing or damaged equipment components, such as swing seats.
• Remove plastic swing seats and take indoors (or do not use) when the
temperature drops below 32°F.
• Oil all metallic moving parts monthly during the usage period.
• Check swing seats, ropes, cables, and chains monthly during usage
season for evidence of deterioration. Replacement should be made of
any swing seat or climbing footers that have developed cracks in the
plastic. Ropes, cables, and chains should be removed and replaced if
excessive wear is found.
After reading all the safety information on this page and the rst
page, you may now start to assemble your wooden skateboard swing
using the following directions.
PIECES: Make sure all parts are present & place them side by side for
easy identication
INSTALLATION:
1. Do not install Disc Swing over concrete, asphalt, packed earth, or
any other hard surface. See the "Consumer Information Sheet for
Playground Surfacing Materials" section for more information on
proper protective surfacing material.
2. Conrm that the supporting structure is secure, it will support at
least 250 pounds, is over level ground, and is no less than 6 feet on
all sides from vertical elements.
3. Attach the carabiner hook to the hanging rope. Wrap this rope
around the support structure and thread it though itself. Pull taut.
4. Attach the “O” ring of the Disc Swing to the carabiner.
**The maximum fall height for this product is 60 in (152 cm).
We reccommend using 6 in (15 cm) of Double Shredded Bark Mulch. **
Product Warranty: All Bliss Hammock products are guaranteed against
manufacturing defects for 1 full year from the date of purchase. Damage
caused by the environment, improper use, or improper care and
maintenance is not covered.
*Guarantee excludes clearance/closeout items, non-retail, private sales, and
auction website sales.
Support Structure
Do not install Disc Swing over concrete, asphalt, packed earth,
or any other hard surface. See the "Consumer Information
Sheet for Playground Surfacing Materials" section for more
information on proper protective surfacing material.
Confirm that the supporting structure is secure, it will support
at least 250 pounds, is over level ground, and is no less than 6
feet on all sides from vertical elements.
Attach the carabiner hook to the hanging rope. Wrap this rope
around the support structure and thread it though itself. Pull
taut.
Attach the “O” ring of the Disc Swing to the carabiner.
INSTALLATION
ROPE CLIMBER SWING
Find a support structure that is at least 95” above the
ground and can support at least 250 pounds.
At least 37”
circumference.
1
2
3
4
Distance from ground should not
exceed 16"; the maximum fall height
should not be more than 16"
Clearance distance should
be 6 feet around the swing.
MAX 16"
Product Warranty: All Bliss Hammock products are guaranteed against
manufacturing defects for 1 full year from the date of purchase. Damage
caused by the environment, improper use, or improper care and
maintenance is not covered.
*Guarantee excludes clearance/closeout items, non-retail, private sales, and
auction website sales.
Support Structure
Do not install Disc Swing over concrete, asphalt, packed earth,
or any other hard surface. See the "Consumer Information
Sheet for Playground Surfacing Materials" section for more
information on proper protective surfacing material.
Confirm that the supporting structure is secure, it will support
at least 250 pounds, is over level ground, and is no less than 6
feet on all sides from vertical elements.
Attach the carabiner hook to the hanging rope. Wrap this rope
around the support structure and thread it though itself. Pull
taut.
Attach the “O” ring of the Disc Swing to the carabiner.
INSTALLATION
ROPE CLIMBER SWING
Find a support structure that is at least 95” above the
ground and can support at least 250 pounds.
At least 37”
circumference.
1
2
3
4
Distance from ground should not
exceed 16"; the maximum fall height
should not be more than 16"
Clearance distance should
be 6 feet around the swing.
MAX 16"
Product Warranty: All Bliss Hammock products are guaranteed against
manufacturing defects for 1 full year from the date of purchase. Damage
caused by the environment, improper use, or improper care and
maintenance is not covered.
*Guarantee excludes clearance/closeout items, non-retail, private sales, and
auction website sales.
Support Structure
Do not install Disc Swing over concrete, asphalt, packed earth,
or any other hard surface. See the "Consumer Information
Sheet for Playground Surfacing Materials" section for more
information on proper protective surfacing material.
Confirm that the supporting structure is secure, it will support
at least 250 pounds, is over level ground, and is no less than 6
feet on all sides from vertical elements.
Attach the carabiner hook to the hanging rope. Wrap this rope
around the support structure and thread it though itself. Pull
taut.
Attach the “O” ring of the Disc Swing to the carabiner.
INSTALLATION
ROPE CLIMBER SWING
Find a support structure that is at least 95” above the
ground and can support at least 250 pounds.
At least 37”
circumference.
1
2
3
4
Distance from ground should not
exceed 16"; the maximum fall height
should not be more than 16"
Clearance distance should
be 6 feet around the swing.
MAX 16"
x1
Disc Swing Carabiner
Hanging Rope
x1x1
Package Contents
Make sure all parts are present & place
them side by side for easy identification.
STEP 1
Find a healthy, strong hardwood tree that has a branch* that stretches at least 8
feet (2.4m) from its trunk and has a circumference** between 25
1
/
4
to 100 inches
(64.1 to 254cm). The tree branch should be at least 8 feet (2.4m) from the ground.
The tree trunk should have a circumference of at least 25
1
/
4
inches (64.1cm). The
tree and its branch should be strong enough to hold at least 200 lbs. (90.7 kgs.)***.
Clear the surrounding ground of debris prior to installing your swing. Make sure
the tree branch does not stretch: into a road, sidewalk, or street; over a
fence; someone else’s property; or any other obstacle.
*The tree branch must allow at least 12 inches (30.5cm) of clearance between the skateboard swing
& ground. The skateboard swing ropes are about 66 inches (167.6cm) in length.
**9-ft tree straps can only wrap around a tree branch of a max 100-inch (254cm) circumference.
Helpful hint: wrap tree straps around the tree branch for height adjusting purposes.
***Please note that the skateboard swing can only hold a person weighing up to 200 lbs.
Preassembled Skateboard Swing has:
4 Ropes
4 ‘O’ Rings
Wooden skateboard, &
Wooden handles
A
B
C
D
A
B
C
D
x1
x2
x2
PART
1
2
3
NAME QTY
Preassembled
Skateboard Swing
Carabiner Hooks
w/ Screw Lock
9-Ft Tree Straps
ASSEMBLY INSTRUCTIONS
AFTER READING ALL THE SAFETY INFORMATION ON
THIS PAGE AND THE FIRST PAGE, YOU MAY NOW
START TO ASSEMBLE YOUR
WOODEN SKATEBOARD SWING
USING THE FOLLOWING DIRECTIONS
CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS
Product Warranty: All Bliss Hammock products are guaranteed against
manufacturing defects for 1 full year from the date of purchase. Damage
caused by the environment, improper use, or improper care and
maintenance is not covered.
*Guarantee excludes clearance/closeout items, non-retail, private sales, and
auction website sales.
Support Structure
Do not install Disc Swing over concrete, asphalt, packed earth,
or any other hard surface. See the "Consumer Information
Sheet for Playground Surfacing Materials" section for more
information on proper protective surfacing material.
Confirm that the supporting structure is secure, it will support
at least 250 pounds, is over level ground, and is no less than 6
feet on all sides from vertical elements.
Attach the carabiner hook to the hanging rope. Wrap this rope
around the support structure and thread it though itself. Pull
taut.
Attach the “O” ring of the Disc Swing to the carabiner.
INSTALLATION
ROPE CLIMBER SWING
Find a support structure that is at least 95” above the
ground and can support at least 250 pounds.
At least 37”
circumference.
1
2
3
4
Distance from ground should not
exceed 16"; the maximum fall height
should not be more than 16"
Clearance distance should
be 6 feet around the swing.
MAX 16"
Loading ...