Loading ...
NS58000 SERIES
Page 2
CLEANING & MAINTENANCE
Proper maintenance of the Range Hood will assure proper performance
of the unit.
MOTOR
The motor is permanently lubricated and never needs oiling. If the motor
bearings make excessive or unusual noise, replace the motor with the
exact service motor. The impeller should also be replaced.
GREASE FILTERS
The grease filters should be cleaned frequently. Use a warm dishwashing
detergent solution. Grease filters are dishwasher safe.
Clean all-metal filters in the dishwasher using a non-phosphate deter-
gent. Discoloration of the filters may occur if using phosphate detergents,
or as a result of local water conditions - but this will not affect filter perfor-
mance. This discoloration is not covered by the warranty.
Remove grease filters by pulling down on the metal latch tab. This will
disengage the filter from the hood. Tilt the filter downward and remove.
NON-DUCTED RECIRCULATION FILTERS
The non-ducted recirculation filters should be changed every 6 months.
Replace more often if your cooking style generates extra grease, such
as frying and wok cooking. Turn the filter mounting tabs to remove filter
and replace.
STAINLESS STEEL CLEANING
DO:
• Regularlywashwithcleanclothorragsoakedwithwarmwaterand
mild soap or liquid dish detergent.
• Alwayscleaninthedirectionoforiginalpolishlines.
• Alwaysrinsewellwithclearwater(2or3times)aftercleaning.Wipe
dry completely.
• Youmayalsouseaspecializedhouseholdstainlesssteelcleaner.
DON’T:
• Useanysteelorstainlesssteelwooloranyotherscraperstoremove
stubborn dirt.
• Useanyharshorabrasivecleansers.
• Allowdirttoaccumulate.
• Let plaster dustor any other construction residues reach the hood.
During construction/renovation, cover the range hood to make sure no
dust sticks to the stainless steel surface.
Avoid: When choosing a detergent
• Anycleanersthatcontainbleachwillattackstainlesssteel
• Anyproductscontaining:chloride,fluoride,iodide,bromidewilldeterio-
rate surfaces rapidly.
• Anycombustibleproductsusedfor cleaning such asacetone,alco-
hol, ether, benzol, etc., are highly explosive and should never be used
close to a range.
OPERATION
The hood is operated using the push buttons on the front panel.
LIGHTS
Push the button to turn the lights ON and OFF.
BLOWER
Push the button once to turn blower ON to LOW SPEED.
Blower symbol will be illuminated. When blower is initially turned
on, it will start on HIGH SPEED for 1 second, then return to LOW
SPEED. To increase the blower speed, push the
button until
the desired speed is obtained. When highest speed setting is
selected, the
button will not be illuminated.
Push the
button to decrease the blower speed until the
desired speed is obtained. Continue to push the
button to
turn blower OFF.
BLOWER DELAY
When blower is ON, push the button to activate the
10-minute delay off. Delay symbol will flash on/off once activated.
Blower will continue to operate for 10 minutes and then will stop
automatically. (Delay off setting does not affect lighting.)
To cancel delay function, push
button again. The blower will
continue to operate and will not stop until turned off using the
button.
Note: Delay will be reset if blower speed is modified during delay
setting mode.
LIGHT BULBS
!
CAUTION: Bulbs may be hot. Always allow
bulbs to cool down before removing them.
This range hood includes two incandescent bulbs (Type B10,
120V, 40W Max, candelabra).
To install or change bulbs:
1. Remove grease filter(s) by pulling down the metal latch
and tilting filter down.
2. Remove and discard bulb. Replace with new bulb.
3. Re-install grease filter(s).
BLOWER ON
& SPEED
INCREASE
BLOWER
SPEED
DECREASE
& OFF
BLOWER
DELAY
OFF
LIGHTS
ON / OFF
Loading ...
Loading ...
Loading ...