Module No.1978
1978-1
GENERAL GUIDE
· Press
CC
to change from mode to mode.
· In the Timekeeping Mode and Alarm Mode, press
DD
to illuminate the display for about two seconds. In the Countdown Alarm Mode and Stopwatch Mode, press
EE
to illuminate the
display.
Stopwatch Mode Countdown Alarm Mode Alarm Mode
Timekeeping Mode
TIMEKEEPING MODE
To set the time and date
1.Hold down
AA
while in the Timekeeping Mode
until the seconds digits flash on the display.
2.Press
CC
to change the selection (flashing) in
the following sequence.
3.While the seconds setting is selected
(flashing), press
EE
to reset it to 00. If you
press
EE
while the seconds setting is in the
range of 30 to 59, the seconds are reset to 00
and 1 is added to the minutes. If the seconds
setting is in the range of 00 to 29, the minutes
count is unchanged.
4.While any other setting (beside seconds) is selected (flashing), press
EE
to
increase it or
BB
to decrease it. While the 12/24-hour format setting is selected,
press
EE
to toggle it between 12 and 24.
· Except for the seconds or 12/24-hour setting, holding down a button changes the
setting at high speed.
· When the 12-hour format is selected, the indicator P appears on the display to
indicate “P.M.” times. There is no indicator for “A.M.” times.
5.After you set the time and date, press
AA
to return to the Timekeeping Mode.
· The day of the week is automatically set in accordance with the date.
· The date can be set within the range of January 1, 1995 to December 31, 2039.
· If you do not operate any button for a few minutes while a setting is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
ABOUT THE BACKLIGHT
About the Auto Light Switch Function
When the auto light switch function is turned on, the backlight automatically turns on
for two seconds under the conditions described below. Avoid wearing the watch on
the inside of your wrist. Doing so causes the auto light switch to operate when not
needed, which shortens battery life.
Month
Day
Minutes
PM
indicator
Day of
week
Hour
Seconds
Seconds
Hour
Month YearDay
Minutes
12/24-HourFormat
· The backlight may not illuminate if the face of the watch is more than 15 degrees
off parallel to the left or right. Make sure that the back of your hand is parallel to
the ground.
· Static electricity or magnetic force can interfere with proper operation of the auto
backlight function. If the auto backlight does not illuminate, try moving the watch
back to the starting position (parallel with the ground) and then tilt it back toward
you again. If this does not work, drop your arm all the way down so it hangs at
your side, and then bring it back up again.
· Under certain conditions the backlight may not light until about one second or less
after turn the face of the watch towards you. This does not necessarily indicate
malfunction of the backlight.
To switch the auto light switch function on and off
In the Timekeeping Mode, hold down
EE
for one or two seconds to turn the auto light
switch function on and off.
Parallel to ground More than 15 degrees
too high
More than 15 degrees
too low
Moving the watch to a position that is parallel to the ground and then tilting it
towards you approximately 40 degrees causes the backlight to illuminate.
Parallel to
ground
40°
· The auto light switch indicator is shown on the display in all modes while the auto
light switch function is on.
· In order to protect against running down the battery, the auto light switch function
is automatically turned off approximately six hours after you turn it on. Repeat the
above procedure to turn the auto light switch function back on if you want.
· Pressing
DD
(Timekeeping Mode, Alarm Mode) or
EE
(Countdown Alarm Mode,
Stopwatch Mode) illuminates the display for about two seconds, regardless of the
backlight’s on/off setting.
Caution
· The backlight of this watch employs an electro-luminescent (EL) light, which loses its
illuminating power after very long term use.
· Frequent use of the backligfht shortens the battery life.
· The watch emits an audible sound whenever the display is illuminated. This is because the
EL light vibrates slightly when lit. It does not indicate malfunction of the watch.
Warning!
· Never try to read your watch when mountain climbing or hiking in areas that are
dark or in areas with poor footing. Doing so is dangerous and can result in serious
personal injury.
· Never try to read your watch when running on a roadside or in any other location
where there might be vehicular or pedestrian traffic. Doing so is dangerous and can
result in serious personal injury.
· Never try to read your watch when riding on a bicycle or when operating a
motorcycle or any other motor vehicle. Doing so is dangerous and can result in a
traffic accident and serious personal injury.
· When you are wearing the watch, make sure that its auto light switch function is
turned off before riding on a bicycle or operating a motorcycle or any other motor
vehicle.
Sudden and unintended operation of the auto light switch can create a distraction,
which can result in a traffic accident and serious personal injury.
About the EL Alarm
While the EL alarm feature is turned on, the watch's EL backlight flashes along with
the audible tone when a daily alarm time is reached, when the hourly time signal
sounds, or when the end of a countdown alarm operation is reached. Pressing
DD
while the EL alarm feature is turned on causes the display to remain illuminated for
five seconds, instead of the normal two seconds when the EL alarm is turned off.
To turn the EL Alarm feature on and off
· In the Timekeeping Mode, hold down
BB
until the EL Alarm indicator appears on
(EL alarm on) or disappears from (EL alarm off) the display.
Auto light switch
indicator
Hold down
EE
ON
OFF
STOPWATCH MODE
The stopwatch Mode lets you measure elapsed
time, split times, and two finishes. The range of
the stopwatch is 23 hours, 59 minutes, 59.99
seconds. You can use the EL backlight at any
time while the stopwatch is operating.
ON OFF
EL Alarm indicator
Hold down
BB
Mode indicator
SecondsHours
Minutes
1/100
second
Elapsed time measurement
DD DD DD DD BB
Start Stop Re-start Stop Clear
Split time measurement
DD BB BB DD BB
Start Split Split release Stop Clear
Split time and 1st-2nd place times
DD BB DD BB BB
Start Split Stop Split release Clear
First runner
finishes.
Second runner
finishes.
Record time of
first runner.
Record time of
second runner.
Loading ...
