Lasko S16612 16" PEDESTAL FAN with REMOTE OSCILLATION CONTROL and THERMOSTAT

OPERATING MANUAL - Page 2

For S16612.

PDF File Manual, 8 pages, Read Online | Download pdf file

S16612 photo
Loading ...
NEW 9/18 2 2084865
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
CAUTION
AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these de-
vices may overheat and cause a fire hazard.
DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a
fire hazard.
ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
DO NOT block, cover or obstruct air flow to or from the fan while in operation.
DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may
create a shock hazard.
DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will not be tripped over.
NEVER use a single extension cord to operate more than one Fan or other electrical device.
DO NOT use this Fan if it has been damaged or is not functioning properly.
• Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,
move the Fan to another location.
• Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).This Fan is not suitable for use in agricultural facil-
ities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7
(2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).This Fan is not suitable for use in hazardous lo-
cations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user is cautioned that changes
and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!
ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet and
create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition should
be replaced by a qualified electrician.
ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means
of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the
Fan when not in use.
BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The Blue Plug
on your Lasko fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed
or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace, repair or tamper
with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.
THIS FAN HAS A POLARIZED PLUG (one blade is wider than the other). This plug is designed to fit into the outlet only one way.
Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety feature. If the
plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced.
NEW 9/18 7 2084865
MODELO S16612
FUNCIONAMIENTO
Este Ventilador puede hacerse funcionar mediante los Controles ubica-
dos en la parte superior de la unidad (como se muestra en la Figura 1)
o con el Control Remoto.
1. Conecte el cable eléctrico a un tomacorriente de 120 V~.
2. Coloque el ventilador sobre una superficie firme y nivelada.
Asegúrese que el enchufe encaje
firmemente en el tomacorriente.
Cuando los enchufes quedan flojos en los tomacorrientes,
pueden deslizarse parcial o completamente fuera del toma-
corriente con un leve movimiento del cable adosado. Los
tomacorrientes en este estado podrían sobrecalentarse y
representar un grave peligro de incendio; si está cubierto
por una cortina o tela, el riesgo de incendio es aún mayor.
3. Conecte la energía eléctrica a su ventilador pulsando el Bon Ali-
mentación ( ).
4. VELOCIDAD DEL VENTILADOR: Ahora puede ajustar la velocidad del
ventilador al nivel deseado pulsando el Botón Alimentación.
5. OSCILACION: Presion el Botón Oscilación
( )
para hacer girar la
cabeza del ventilador de lado a lado.
6. FUNCIÓN DE TEMPORIZADOR: Este ventilador está equipado con
un temporizador. El temporizador puede ser programado 7 horas.
Continúe oprimiendo el Botón Temporizador ( ) para lograr el tiempo
de programación deseado. Para cancelar el temporizador, presione el
Botón Temporizador ( ) hasta que se apague la luz.
7. FUNCIÓN DE TERMOSTATO: La función del Termostato siente la tem-
peratura ambiente y enciende o apaga el Ventilador automáticamente
a medida que cambia la temperatura. Presione el Botón Termostato
( ) para seleccionar una temperatura 60°F, 65°F, 70°F, 75°F, 80°F,
o el modo manual (abajo). Su Ventilador ahora se Encenderá y se
Apagará a esta temperatura. La luz al lado de la temperatura fijada
titilará hasta que el aire de la habitación baje a esa temperatura.
Luego el Ventilador se apaga y la luz se queda fija. El termostato se
puede utilizar en cualquier configuración de velocidad.
NOTA: Este ventilador circula el aire de la habitación, no acondiciona ni
cambia la temperatura del aire de la habitación.
El modo manual opera el ventilador de manera continua. El ventilador
comienza en el modo manual cuando se enciende inicialmente.
8. Después de encender el ventilador apagado, desenchufe la unidad de la
toma eléctrica.
ENSAMBLAJE DE LA BASE, EL TUBO Y EL MOTOR
Alinee y presione el tubo en la base. Afloje la rosca de ajuste de la
altura al girar en el sentido contrario a las agujas del reloj y subir
el tubo interno. Apriete la rosca de ajuste de la altura al girarla en
el sentido de las agujas del reloj. Alinee el Ensamblaje de la parte
superior y presione en el tubo.
PARTES INCLUIDAS
2 3
4
6
8 9
5
7
1.5V AAA
1.5V AAA
10
POWER
TIMER
SPEED
OSC
TEMP
POWER
TIMER
OSC
1
Base
Rotador
Aspa
Tuerca de
Protección
Rejilla Delantera
Control Remoto
Baterías
Rejilla Trasera
Tubo Ensamblaje de
la Parte Superior
ENSAMBLAJE DE LA REJILLA Y EL ASPA
Alinee la rejilla trasera y presiónela en el ensamblaje de la parte
superior. Conecte la rosca de protección y fíjela al girarla en el
sentido de las agujas del reloj. Coloque el aspa en la rejilla trasera
y fíjela con el Rotador al girarla en el sentido contrario a las agujas
del reloj. Encaje la rejilla delantera en la rejilla trasera.
Rotador
Aspa
Tuerca de
Protección
Rejilla Delantera
Rejilla Trasera
5
4
6
8
7
1
2
3
Base
Tubo
Ensamblaje
de la Parte
Superior
IMPORTANTE: Su Ventilador pedestal LASKO está equipado con Ter-
mostato de Control de Clima. Este Termostato funciona detectando
la temperatura de la habitación y encenderá o apagará el Ventilador
AUTOMÁTICAMENTE a medida que cambie la temperatura.
Termostato
Alimentación
Figura 1
Temporizador
Oscilación
Loading ...
Loading ...
Loading ...