Loading ...
Loading ...
Loading ...
SOUND OPTIONS
Sound OFF
Press *633 on keypad
Beep ON
Press *66 on keypad
OPEN SAFE WITH EMERGENCY KEY
1. To expose the Emergency Key access, remove Logo
Plate screws with provided tool
2. Insert Emergency Key into key access, push and turn
key counter-clockwise, and turn Handle clockwise to
open the safe
NOTE: Store Emergency Keys in a secure place, NOT
inside of the safe
LOW BATTERY WARNING
1. When the door is closed and 3 repetitive beeps are
heard, and Indicator Lights flash red, it indicates the
batteries are low
2. Replace batteries immediately
- Open safe, remove Battery Compartment cover and
all 4 AA batteries
- Insert 4 new AA batteries and restore Battery
Compartment cover
NOTE: After batteries are out over 24 hours, all the
registered PIN codes will not be retained. Please use the
key to open the safe and reset the PIN codes.
CARE AND MAINTENANCE
- To maximize the security and performance of the safe,
keep keypad clean; use a dry cloth to remove any
smudges after each use
- Keep liquids away from the control panel. Spills on the
control panel will cause damage and possibly
electric shock
- Secure safe in a proper area to prevent from falling and
causing damage or injury
- DO NOT disassemble the product. For all repairs, contact
BARSKA Customer Service
- DO NOT use chemicals or cleaning agents to clean
the safe
MOUNTING INSTRUCTIONS
The safe must be mounted to a wall or floor. Be aware
of the load bearing. Failure to do so can result in
personal injury and/or damage to property. Use
appropriate tools when performing work and always use
eye protection
Wall Mounting
Do not mount the safe without anchoring to the wall
- Find the studs in the wall, at your desired location.
Most studs are 16 inches or 24 inches apart
- Check the wall for concealed wires or pipes Measure
the location of the pre-set drill holes; mark their exact
position onto the wall ensuring that the studs or
anything else behind will not interfere
- Drill the appropriate size holes for the anchors you
are using
- Carefully press the anchor into the holes at this time
- Mount the safe by running screws from inside of the
safe and securing to anchors; ensure the safe is
mounted securely
Floor Mounting
- Use proper drill tools depending on the type of floor
you are mounting the safe (wood, tile, or concrete)
- Measure the location of the pre-set drill holes; mark
their exact position onto the floor
- Drill the appropriate size holes for the anchors you
are using
- Carefully press the anchor into the holes at this time
- Mount the safe by running screws from inside of the
safe and securing to anchors; ensure the safe is
mounted securely
12/19
BC629
Safe
12/19
BARSKA warrants this new safe to be free of original defects
in material and/or workmanship under normal use for a
period of twelve (12) months from the date product is
received by purchaser. This warranty does not include
damage caused by improper installation or maintenance.
Damage from misuse, abuse, accident (such as dropping),
normal wear and tear, fire, flood, or acts of nature. Damage
from service or repairs other than those performed by
BARSKA. Labor, cost and shipping charges for the removal
and replacement of defective parts beyond the initial
twelve-month warranty period. All transportation and shipping
charges. Removing or altering the seal under any
circumstances will automatically void the warranty.
This warranty is limited to original purchaser and is not
transferable. This warranty applies only to products
purchased in the United States.
Please email [email protected] or call 1.888.666.6769 for
Return Merchandise Number (RMA#) before any returns. The
RMA number must appear on the outside of the shipping
package. Product must be packed carefully and sturdily in its
original packaging to prevent damage in transit and returned
freight pre-paid to:
BARSKA OPTICS
Repair Department
855 Towne Center Drive
Pomona, CA 91767
Please include all of the following when returning BARSKA
products for service and/or replacement:
1. Please write your complete details (Name, Address,
Telephone #, E-mail address, RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order to cover inspection, shipping and
handling. Charges are as follows
$90 - Large
$60 - Standard
BARSKA will examine and test returned product and repair or
replace defective part(s) or units with new part(s) or a new
unit if necessary within the warranty period. Purchaser is
for return shipping
and handling at time product is returned. If repair is required
after warranty period expiration, purchaser will be
charged for replacement parts and return shipping.
BARSKA® Optics shall not be liable for any consequential,
incidental and/or contingent damages whatsoever. We will
not pay shipping, insurance or transportation charges from
you to us, or any import fees, duties and or taxes. This
warranty supersedes all previous BARSKA® Optics
warranties.
1 YEAR LIMITED WARRANTY
required to remit amount above to BARSKA
Loading ...
Loading ...