Loading ...
Loading ...
Loading ...
CD DISC PROGRAMMING (BY REMOTE CONTROL)
UP TO 40 TACKS CAN BE PROGRAMMED FOR CD OR MP3 FILE AND PLAY IN ANY ORDER. BEFORE USE, BE
SURE THE SYSTEM IS AT STOP MODE BEFORE PROGRAMMING:-
1. SET IN CD/USB MODE & STOP THE CD PLAYBACK.
2. PRESS THE “PROGRAM” BUTTON, “ PROG “ WILL APPEAR ON LCD DISPLAY (2). MOREOVER, IT WILL
INDICATE PROGRAM NO. AND DIGITS FOR TRACK NO. TO BE PROGRAMMED.
3. SELECT A DESIRED TRACK BY PRESSING SKIP
(24) OR BUTTONS (13).
4. PRESS THE “ PROGRAM ” BUTTON TO STORE THE TRACE INTO MEMORY.
5. REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.
6. WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS CD “ PLAY/PAUSE/STOP ”
BUTTON (16) TO PLAY THE DISC IN ASSIGNED ORDER.
7. TO CANCEL THE PROGRAMMED FILE, PRESS “STOP” BUTTON ON REMOTE HANDSET UNTIL “ PROG “ IS
DISAPPEAR ON LCD DISPLAY (2)
PLAYBACK OF MP3 SONG VIA USB STORAGE MEDIA OR MEMORY CARD
CONNECTING
THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3 FILE WHICH STORED IN THE MEMORY MEDIA
WITH USB CONNECTING PORT OR SD/MMC MEMORY CARD.
1. SET FUNCTION SELECTOR (6) AT USB/SD POSITION AND THEN
PRESS SOURCE BUTTON (4) TO SELECT “ USB OR CARD” MODE.
2. PLUG-IN THE USB PLUG WITH THE FACE UP & MAKE SURE IT GOING
INTO COMPLETELY OR INSERT THE MEMORY CARD IN THE
DIRECTION OF THE ARROW AS SHOWN IN THE LABEL ON THE
UNDERSIDE OF THE MEMORY CARD SLOT COVER. INSERT
STRAIGHT WITHOUT BENDING.
CONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD
DAMAGE THE AUDIO SYSTEM OR THE STORAGE MEDIA (USB
THUMB DRIVE / SD/MMC CARD). CHECK TO BE SURE THE
DIRECTION IS CORRECT BEFORE CONNECTION.
3. THE SYSTEM WILL START READING THE STORAGE MEDIA
AUTOMATICALLY AFTER CONNECTING, AND LCD DISPLAY (2) WILL
SHOW THE TOTAL NUMBER OF MP3 FILES AND TOTAL NUMBER
OF FOLDER BEING DETECTED.
4. REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3
DISC AS ABOVE
REMARK
- THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 FORMAT ONLY THOUGH THE
USB PORT.
- IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3
ENCODING FORMAT, SOME MP3 PLAYER MAY
NOT BE ABLE TO PLA
Y VIA THE USB SOCKET. THIS IS
NOT A MAUFUNCTION OF THE SYSTEM.
- USB PORT DOES NOT SUPPORT CONNECTION WITH USB EXTENSION CABLE AND IS NOT DESIGNED
FOR COMMUNICATION WITH COMPUTER DIRECTLY.
PHONO
NOTED:
- REMOVE THE STYLUS PROTECTOR.
- BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
1. SELECT TO “ PHONO ” FUNCTION (6).
2. SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE
RECORD TO BE PLAYED.
3. PLACE THE RECORD ON THE PLATTER (USE THE SPINDLE ADAPTOR IF REQUIRED).
4. LIFT THE TONE ARM FROM THE REST AND SLOWLY MOVE IT TO THE RECORD SIDE.
THE PLATTER WILL START TO ROTATE.
5. PLACE THE TONE ARM TO THE DESIRED POSITION OF THE RECORD.
6. ADJUST THE VOLUME TO THE DESIRED LEVEL.
7. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. LIFT THE TONE ARM
FROM THE RECORD AND RETURN IT TO THE REST.
8. TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.
REMARK : AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST RACK FINISH. IN THIS CASE, SELECT THE AUTO-STOP SWITCH TO “ OFF
“ POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH (32) TO “ ON “ POSITION TO STOP
THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE REST POSITION.
EN-6
Loading ...
Loading ...
Loading ...