Loading ...
Yoursafetyandthesafetyof
othersisveryimportant.
Wehaveprovidedmanyimportant
safetymessagesinthismanualand
onyourappliance.Alwaysreadand
obeyatlsafetymessages.
Thisisthesafetyalertsymbol.
Thissymbolalertsyouto
potentialhazardsthatcankill
orhurtyouandothers.Alisafety
messageswiiifoliowthesafetyalert
symbolandeithertheword"DANGER"
or"WARNING".Thesewordsmean:
YouGanbe killed or seri0usly injured
if you don't f011owinstructions.
AIi safety messageswili teli you what
the potentiai hazardis, teii you how to
reducethe chance of injury, and tell
you what can happenif the
instructions are not followed.
important: Observe all governing
codes and ordinances.
Proper instaUadon is your
responsibility. Make sure you have
everything necessary for correct
instaUation, It is the responsibility of
the installer to comply with the
clearances specified.
Check the location where the range
hood will be instalbd.The location
should be away from strong draft
areas, such as windows, doors, and
strong heating vents.
Mobile home installation
The installation of this range hood
must conform to the Manufactured
Home Construction Safety
Standards, Titb 24 CFR, Part 328
(formerly the Federal Standard for
Mobile Home Construction and
Safety, Title 24, HUD, Part 280 or
when such standard is not
applicable, the Standard for
Manufactured Home Installation
1982 (Manufactured Home Sites,
Communities and Setups) ANSi
A225.1/NFPA 501A*, or latest edition,
or with local codes.
WARNING -- TO REDUCE THE
RiSK OF FIRE, ELECTRIC
SHOCK, OR iNJURY TO
PERSONS, OBSERVE THE
FOLLOWING:
Installation work and electrical
wiring must be done by qualified
person(s) in accordance with all
applicable Codes and Standards,
including Fire Rated Construction.
Sufficient air is needed for proper
combustion and exhausting of
gases through the flue (chimney)
of fuel burning equipment to
prevent back drafting. Follow the
heating equipment
manufacturer's guideline and
safety standards such as those
published by the National Fire
Protection Association (NFPA),
and the American Society of
Heating Refrigeration and Air
Conditioning Engineers
(ASHRAE), and the local code
authorities.
When cutting or drilling into wall or
ceiling, do not damage electrical
wiring and other hidden utilities.
Ducted fans must always be
vented to the outdoors.
WARNING -- To reduce the risk
of fire, use only metal ductwork.
This unit must be grounded.
This hood is factory set for vented
installations. For non=vented
installations, purchase Filter Kit
No. 4396388 from your dealer.
Tools and
materials needed
for installation:
fiat hmade _ 14/4" (3.0 cm}
screwdriver drill hit
pmiers _ I/8" (or 3 fatal drill
drill bit for pilot homes
ruiner _ pencil
For vented installations, you amsoneed:
compass or 8" • duct tape
120.3 era} eircme " 7" 117.8era) round
terapmate damper if using
• raetamsnips 7" 117.8era) round
• keyhome saw vent system
® saber saw
Cabinets with recessed bottoms:
2, 2" 15.8era} wide filler strips. Length and
thickness determined by recess diraensions.
4 wood screws or fiat head raachine screws
with washers and nnts to attach filler strips.
Parts supplied:
amurainura mesh filter
* baffle pmateIvented installations}
_3-1/4"× 10"18.3x25.4era)damper/vent
connector
parts hag
7" 117.8era} round adapter
important: Observe all governing
codes and ordinances.
it is the customer's responsibility:
,, To contact a qualified electrical
installer.
• To assure that the electrical
installation is adequate and in
conformance with National
Electrical Code, ANSI/NFPA 70
-- latest edition*, or CSA
Standards C22.1-94, Canadian
Electrical Code, Part 1 and
C22.2 No,O=M91 =latest
edition** and all local codes
and ordinances.
A separate ground wire must be
used. it is recommended that a
qualified electrician determine that
the ground path is adequate.
A 120-volt, 60-Hz, AS-only, fused
electrical system is required. A
separate 15=amp circuit is
recommended.
Do not ground to a gas pipe.
Check with a qualified electrician if
you are not sure range hood is
properly grounded.
Do not have a fuse in the neutral or
ground circuit.
IMPORTANT:
Save installation instructions for
electrical inspector's use.
The range hood must be connected
with copper wire only.
The range hood should be
connected directly to the fused
disconnect (or circuit breaker) box
through flexible armored or
nonmetallic sheathed copper cable.
A U.L.° or C.S.A.=listed strain relief
must be provided at each end of the
power supply cable. Wire sizes
(COPPERWIRE ONLY) and
connections must conform with the
rating of the appliance as specified
on the model/serial rating plate.
Loading ...
Loading ...
Loading ...