Loading ...
Loading ...
Loading ...
8
Sleep Mode
SLEEP mode is used to conserve energy and can be used when
the unit is in the COOL, HEAT or AUTO mode only.
Cool Mode
a. Push SLEEP. After 1 hour the set point raises by 1.8_F
(1_C). After another hour, the set point raises by another
1.8_F (1_C) and the fan runs in a low speed. The unit
shuts off 5 hours after setting the SLEEP mode. The
SLEEP mode cancels if either MODE, TEMP, FAN,
TIMER, or ON/OFF on the remote control are pressed.
Heat Mode
Same as cooling mode however set points are lowered by 1.8_F
(1_C).
Turbo Mode
Use the TURBO mode to cool or heat the room rapidly.
a. Press TURBO. An audible “beep” is heard if the indoor
unit supports this function. The fan runs on super high
speed. The TURBO mode terminates automatically 20
minutes after pushing TURBO. It can be terminated
immediately by selecting TURBO again. When the
TURBO mode is terminated, the unit reverts to the
original setting.
Self Clean Mode (Available only on sizes 18 to 24)
Press CLEAN to activate or deactivate the self−cleaning function.
Under this function, the air conditioner automatically cleans and
dries the evaporator. The cleaning cycle takes 16 minutes, after
which the unit turns off automatically. Pressing CLEAN in the
middle of the cycle cancels the operation and turns off the unit.
This function can be activated only in the COOL or DRY mode.
Follow Me Mode
Press FOLLOW ME to activate or deactivate this function.
Under this setting, the temperature that appears in the remote
control is the actual temperature at its location. The remote
control sends this signal to the air conditioner every 3 minutes.
This function is not available for DRY and FAN modes.
This function can also be deactivated if:
1. No FOLLOW ME signal is received by the unit for
continuous 7 min
2. Users adjust the operation mode
3. Users turn off the unit
4. Users turn off the FOLLOW ME function
NOTE: If FOLLOW ME is used with the wireless remote
controller, make sure that the remote’s IR sender is within
line−of−sight of the IR receiver of the unit and is within the
maximum range of 25 feet of the indoor unit. If FOLLOW ME is
de−activated by pressing MODE, OFF or FOLLOW ME on the
remote, the icon on the remote will turn off.
Freeze Protection Mode
Press FP for approximately 2 seconds to activate or deactivate
the freeze protection mode (heating set back). The indoor unit
displays “FP”.
NOTE: This function is only available in the heating mode.
Under this function, the unit operates at high fan speed and the coil
temperature automatically sets to 46_F (8_C). This mode can also
be deactivated by pressing ON/OFF, SLEEP, MODE, FAN, or
either TEMP.
Silence Mode
NOTE: The Silence Mode (SLC) feature is not available on this
model.
LED Light
Press LED to turn the display light on and off.
Resetting the Remote Control
If the batteries in the remote control are removed, the current
settings will be cancelled and the control returns to the initial
settings and will be in standby mode. Push ON/OFF to activate.
Time Delay
If ON/OFF is pressed too soon after a stop, the compressor will
not start for 3 to 4 minutes due to the inherent protection
against frequent compressor cycling. The unit only emits an
audible beep when the signals are received correctly.
Heating Features
If the unit is in the heating mode, there is a delay when the fan
starts. The fan starts only after the coil is warmed up to prevent
cold blow.
Auto Defrost Operation
In HEATING mode, if the outdoor coil is frosted, the indoor
fan and outdoor fan turns off while the system removes the frost
from the outdoor coil. The system automatically reverts to
normal operation when frost is removed from the outdoor unit.
Auto Start
If the power fails while the unit is operating, the unit stores the
operating condition, and the unit will start operation automatically
under those conditions when the power is restored.
Loading ...
Loading ...
Loading ...