Loading ...
Loading ...
0
0
1
3
2
OSC
1
3
2
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY
INSTRUCTIONS
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUC TIONS
F E AT U R E S - OP E R AT I O N S F E AT U R E S - O P E R AT I O N S
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual. This fan is not for continuous operation or
equivalent.
3. To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids and
plug the appliance directly into a 120V AC electrical
outlet.
4. Close supervision is necessary when any appliance is
used near children.
5. Not intended for use by children.
6. Unplug from outlet when not in use, when moving
fan from one location to another.
7. Avoid contact with moving parts.
8. Do not operate in the presence of explosive and/or
flammable fumes.
9. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
10. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
contact customer service.
11. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
12. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
13. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
14. Do not use outdoors.
15. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
16. Always use on a dry, level surface.
17. This product is intended for household use ONLY and
not for commercial or industrial applications.
18. WARNING: To reduce the risk of electrical shock
and injury to persons, do not use in window.
19. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
20. This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse
blows, a short circuit may be present and the product
should be discarded or contact customer service.
21. WARNING: To reduce the risk of fire, electric shock
or injury to persons, do not use replacement parts
that have not been recommended by the
manufacturer. (e.g. parts made at home using
a 3D printer).
!
WARNING: Chemical Burn Hazard. Keep batteries
away from children. This product contains a lithium
button/coin cell battery. If a new or used lithium
button/coin cell battery is swallowed or enters the
body, it can cause severe internal burns and can lead
to death in as little as 2 hours. Always completely
secure the battery compartment. If the battery
compartment does not close securely, stop using the
product, remove the batteries, and keep it away
from children. If you think batteries might have been
swallowed or placed inside any part of the body,
seek immediate medical attention.
OPERATING INSTRUCTIONS
(SEE FIGURE 1)
1. Set the fan base on a dry, level surface.
2. Make sure the Speed Control Knob (A) is in the OFF
(O) position.
3. Plug the cord into a standard 120 volt AC outlet.
4. To turn the fan ON, rotate the Speed Control Knob (A)
to the desired speed setting on the right side of the dial.
(SEE FIGURE 2)
5. To turn the fan ON with oscillation, rotate the Speed
Control Knob (A) to the desired speed setting on the left
side of the dial.
(SEE FIGURE 2)
CLOCK CONTROL
(SEE FIGURE 4)
1. Press and hold the SET button for 3 seconds until
AM/PM is blinking;
2. Adjust flashing AM/PM with the "
∆
" button;
3. Press SET button again to adjust Hour
4. Press SET button a third time to adjust Minutes
5. Press SET button 4 times to lock time
Note: Once SET or "
∆
" keys are pressed, you have 5
seconds to complete operation before the clock reverts to
previous status.
6. Press SET/ to turn on clock backlight. Backlight will
illuminate for 5 seconds.
BEFORE USE / BATTERY REPLACEMENT
(SEE FIGURE 3)
Note: This fan includes one lithium button cell battery,
CR2032.
1. Loosen the screw of the battery cover. Turn the
battery cover counterclockwise to open.
2. Press the battery latch and the lithium battery will
pop up automatically.
3. After taking out the button cell battery, remove
protective sticker and re-install battery.
4. Place the battery cover back on the battery
compartment and rotate clockwise to close.
Tighten screw to lock the battery cover.
5. Follow above steps 1-4 when replacing the lithium
button cell battery. Replace with one CR2032 lithium
button cell battery.
6. Remove battery before discarding the fan.
NOTES:
• Button cell batteries should be disposed of properly,
including keeping them away from children. Even
used button cell batteries may cause injury. Remove
used batteries promptly.
• Do not discard used batteries into household trash
containers. Contact your local government for
disposal or recycling practices in your area.
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
B
A. Control Knob
B Clock
C. Fan Housing
D. Power Cord
Figure 1
Figure 2
Figure 4
C
A
D
SET
Figure 3
This fan comes fully assembled and is ready for use.
Loading ...
Loading ...
Loading ...