Loading ...
Loading ...
Loading ...
Delay start
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay countdown. After adding items, close the door firmly until it
latches. The delay countdown will not continue if the door is not
latched. Press START/RESUME. If the door is unlatched, the
Start/Resume indicator flashes. The delay countdown stops until
you latch the door and press START/RESUME.
3. Press START/RESUME. (The door must be closed.) The delay
countdown starts, and the cycle will begin after the selected
number of hours.
NOTE:
• To cancel the delay and cycle, press CANCEL/DRAIN.
• To cancel the delay and start the cycle immediately, press
START/RESUME.
Model GU2200
To delay the start
1. Press DELAY 1 time for a 2-hour delay, 2 times for a 4-hour
delay, or 3 times for a 6-hour delay. The number glows above
the Delay pad.
2. Select a wash cycle and option or skip to Step 3 to use the
cycle and options selected for last cycle.
3. Press START/RESUME. (The door must be closed.) The Delay
countdown starts, and the cycle will begin after the selected
number of hours.
NOTES:
• To cancel the delay and cycle, press CANCEL!DRAIN.
• To cancel the delay and start the cycle, press START/
RESUME.
Models GU2451, GU2455, and GU2700
• You can delay the start of a cycle up to 9 hours.
• The first time you use Delay, you will see
showing a 1-hour delay.
• After the first time that you use Delay, the control will start by
calling up the last delay that you ran. You can adjust from
there if you want to change it.
To delay the start
1. Repeatedly press DELAY until you see the desired hours of
delay in the display. When the delay reaches 9 hours, the next
selection switches Delay off. Press DELAY again to select a
new number of delay hours.
2. Select a wash cycle and options or skip to Step 3 to use the
cycle and options selected for the last cycle.
3. Press START/RESUME. (The door must be closed.) The delay
countdown starts, and the cycle will begin after the selected
number of hours.
NOTE:
• To cancel the delay and cycle, press CANCEL!DRAIN.
• To cancel the delay and start the cycle immediately, press
START/R ESUM E.
Models GU3200, GU3600
• You can delay the start of a cycle up to 4 hours.
To delay the start
1. Press DELAY. You will see
2. Select a wash cycle and options or skip to Step 3 to use the
cycle and options selected for the last cycle.
Follow the progress of your dishwasher with the Cycle Status
indicators.
SoakingWashingDrying Clean Sanitized
NOTE: Your model may have some or all of the indicators shown
above.
Soaking (on some models)
Soaking glows during the Soaking part of the cycle. Your
dishwasher soaks when Soak & Scour is selected. Washing
pauses for regular intervals during a soak.
Clean
Clean glows when a cycle is finished. The light turns off when you
open and close the door or press any button.
Sanitized
If you select the SANI RINSE TM option, Sanitized glows when the
SANI RINSE TM cycle is finished. If your dishwasher did not
properly sanitize your dishes, the light flashes at the end of the
cycle. This can happen if the cycle is interrupted, or the water
could not be heated to the required temperature. The light goes
off when you open and close the door or press any button.
The Active Vent reduces the sounds from your dishwasher. The
cover closes after the cycle starts. Filling and washing sounds are
reduced. The Active Vent opens when wash action ends and
vapor is vented into room.
NOTE: There is a slight noise when the cover closes or opens.
This is normal.
This dishwasher is equipped with an optical sensor wash that
detects water temperature, soil and detergent amount. Wash
cycles are adjusted based on what is sensed.
The dishwasher "senses" wash water quality during a series of
pauses in the wash cycle. The sensor monitors water
temperature and the amount of soil and detergent appearing in
the wash water. It automatically adjusts the wash cycle for the
best wash. Lightly soiled dishes will use less water and energy.
Heavily soiled dishes will get more water and increased
temperature and wash time. This dishwasher will automatically
adjust the sensor approximately once a year to your water
quality.
IMPORTANT: The very first wash cycle after installation in your
home will be adjusted to include an additional 2 rinses. This cycle
must not be interrupted for proper sensor adjustment. If this
adjustment cycle is canceled or stopped before the Clean light
comes on at the end of the cycle, the next wash cycle will repeat
this sensor adjustment.
17
Loading ...
Loading ...
Loading ...