Loading ...
Loading ...
Loading ...
7
ENGLISH
Soap Tank (J, K)
This pressure washer has a built in soap tank
27
.
1. To remove the soap tank, turn off the pressure washer
and turn off the watersupply.
2. Pull trigger on gun handle to relieve any waterpressure.
3. Lift the soap tank
27
out of the pressure washer unit
8
.
4. Remove soap tank cap
28
and fill with
appropriate detergent following the detergent
manufacturesinstructions.
5. Fit and tighten soap tank cap
28
before reinstalling soap
tank
27
to the pressure washerunit.
6. To clean the soap tank
27
, empty any remaining
detergent back into its bottle. Use water from a garden
hose to thoroughly rinse out the tank. Empty the tank
and allow it todry.
7. Reinstall soap tank to pressure washer unit and ensure the
soap tank is fully secured into the pressure washerunit.
Test Ground‑Fault Circuit‑Interrupter
(GFCI) Before Each Use (Fig. A)
This pressure washer is provided with a ground‑fault
circuit‑interrupter (GFCI) built into the plug of the
power‑supply cord. This device provides additional
protection from the risk of electricshock.
1. Plug the Ground Fault Circuit Interrupter (GFCI) into a
working grounded outlet.
2. The indicator at the top of the GFCI should turn green
when product is ready to use.
3. Press the “TEST” button (bottom). The green indicator
should disappear.
4. Press “RESET” button foruse.
5. Do not use the pressure washer if the above testfails.
Correct Pressure Washer Unit Position
(Fig.A, B)
CAUTION: Before operation:
Always keep the unit right‑side up with its feet
17
and
wheels
21
on the ground as shown in Fig. B.
NOTE: Never attempt to use the pressure washer while
standing vertically, on its side, or flipped over on theground.
Proper Hand Position (Fig.I)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the spray handle
grip
5
and the other hand on the spray handle
4
.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can causeinjury.
NOTE: The tips listed below might not be included with your
pressure washer but are available for purchase at an additionalcost.
Common Spray Tips Common Applications
15 ° Orange Nozzle For brick or masonry.
25 ° Green Nozzle For vinyl siding.
40° White Nozzle For automotive washing.
Soap Nozzle To apply detergents
Black Turbo Nozzle For abrasive cleaning.
Attaching Nozzles (Fig.H)
DANGER: Risk of fluid injection. Do not direct
discharge stream toward persons, unprotected skin,
eyes or any pets or animals. Serious injury willoccur.
WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while
pressure washer is running. Turn pressure washer unit
OFF before changingnozzles.
1. To connect a nozzle to the spray wand
2
, pull the quick
connect collar
3
toward the spray wand and insert the
appropriatenozzle.
2. Release the quick connect collar to lock the nozzle inplace.
3. Give the nozzle a firm tug after the quick connect collar
has locked intoplace to ensure the nozzle is locked
intoplace.
Attaching Garden Hose (Fig.G)
NOTE: Before connecting the garden hose to the pressure
washer unit, run water through the garden hose for thirty
seconds to clear any debris from inside thegardenhose.
1. To connect a garden hose to the
pressurewasherunit
8
,place the end of the
gardenhose
33
inside the water intake
15
.
2. Securely tighten the garden hose byhand.
NOTE: Always disconnect the garden hose afterusage.
Attaching High Pressure Hose (Fig.F)
CAUTION: NEVER PULL WATER SUPPLY HOSE TO
MOVE pressure washer. This could damage hose and/
or pumpinlet.
This pressure washer has a built in storage area to carry the
high pressure hose. The coiled hose is secured between the
cage and the mainbody.
NOTE: Uncoil the high pressure hose
1
before installation to
preventkinks.
NOTE: Avoid cross threading when installing the hose. Cross
threading will causeleaks.
1. To connect the high pressure hose
1
to the handle
grip
5
, thread the hose collar
30
onto the inlet
coupler
31
.
2. To connect the high pressure hose to the pressure
washer unit
8
, thread the hose collar
32
onto the high
pressure water outlet
16
.
Loading ...
Loading ...
Loading ...