Loading ...
Loading ...
3
Features
Specifications
Installation
Wallmount/Under Counter Installation
Reorient the unit’s mounting ears as per the 0U Rackmount Installation above, then put four user-
supplied screws or similar mounting hardware through the unit’s mounting ears and into the
mounting surface. The user must determine the fitness of the user-supplied mounting hardware to
support the unit before mounting.
PDU1215 PDU1220 PDU2430
Nominal Voltage/Frequency: 120V/50 or 60 Hz 120V/50 or 60 Hz 120V/50 or 60 Hz
Output Power Rating (amps): 15 amps 20 amps 24 amps
AC Receptacles: 13 x NEMA 5-15R 13 x NEMA 5-15/20R 24 x NEMA 5-15R
(12 rear/1 front) (12 rear/1 front) (12 rear/12 front)
AC Line Cord: 15', w/NEMA 5-15P plug 15', w/NEMA 5-20P plug 15', w/NEMA L5-30P plug
Circuit Breaker(s) (Resettable): 15 amps 20 amps 2 x 15 amps
Dimensions (HxWxD, inches): 1¾ × 17¼ × 3¾ 1¾ × 17¼ × 3¾ 1¾ × 17¼ × 3¾
PDU121506 PDU1226 PDU1220T6
Nominal Voltage/Frequency 120V/50 or 60 Hz 120V/50 or 60 Hz 120V/50 or 60 Hz
Output Power Rating (amps): 15 amps 20 amps 20 amps
AC Receptacles 13 x NEMA 5-15R 13 x NEMA 5-15/20R 13 x NEMA 5-15/20R
(12 rear/1 front) (12 rear/1 front) (12 rear/1 front)
AC Line Cord: 6’, w/NEMA 5-15P plug 6’, w/NEMA 5-20P plug 6’, w/NEMA L5-20P plug
Circuit Breaker(s) (Resettable) 15 amps 20 amps 20 amps
Dimensions (HxWxD, inches): 1¾ × 17¼ × 3¾ 1¾ × 17¼ × 3¾ 1¾ × 17¼ × 3¾
PDU12IEC PDU1220T
Nominal Voltage/Frequency: 100V to 240V/50 or 60Hz 120V/50 or 60 Hz
Output Power Rating (amps): 15 amps for 100V to 120V or 20 amps
16 amps for 208 to 240V
AC Receptacles: 4 x IEC-C13 (front), 13 x NEMA 5-15/20R
8 x IEC-C13/2 x IEC-C19 (rear) (12 rear/1 front)
AC Line Cord: N/A (IEC320-C20 inlet) 15', w NEMA L5-20P plug
Circuit Breaker(s) (Resettable): 2 x 16 amps 20 amps
Dimensions (HxWxD, inches): 1¾ × 17¼ × 3¾ 1¾ × 17¼ × 3¾
Circuit Breaker(s)
If the current draw of the equipment connected to your power strip exceeds your model’s
Maximum Load Rating (see Specifications) for longer than a few seconds, a circuit breaker will trip
to prevent any possible damage. When a circuit breaker trips, its plunger will pop up. Remove
excess equipment and allow the breaker to cool one minute before depressing its plunger to reset
the breaker.
Grounding Lug
Use this screw (located by the power strip’s receptacles) to connect your power strip to ground.
Input Receptacle (IEC Model Only)
The PDU12IEC has no power cord. Instead, it has a IEC320-C20 inlet receptacle. To connect a
PDU12IEC to utility power, use a user-supplied detachable power cord with an IEC plug on one
end and a plug appropriate to your local utility outlets on the other.
21-03-383-932120.indb 321-03-383-932120.indb 3 4/1/2021 11:00:33 AM4/1/2021 11:00:33 AM
Loading ...
Loading ...
Loading ...