Loading ...
Loading ...
Loading ...
1110
Care & maintenance.
MOTOR BASE:
• For the most part, the motor
base doesn’t really get dirty,
but if you neglect to twist the
extractor blade on to the cup
tightly, liquids can leak out
and get into the base and
stick to the activator buttons.
• To avoid risk of injury, NEVER
use your hands or utensils
to clean the white actuator
Tabs while the NutriBullet
®
is
plugged in.
• Do not remove the rubber or
plastic liners inside the motor
base.
• Use a sponge or dish cloth
dampened with warm soapy
water to wipe down the inside
and outside of the motor base
until clean.
• Pay particular attention
to the white Actuator Tabs
on the inside of the motor
base to loosen any sticky
debris from drips and spills.
If necessary, you may use a
small brush to scrub the area
to ensure it is kept clean.
WARNING: Never submerge
the motor base in water.
Here’s how to clean
the NutriBullet
®
:
STEP 1:
The most important thing
— ALWAYS UNPLUG the
motor base from the power
supply outlet when it is
left unattended, before
assembling, disassembling,
changing accessories or
approaching parts that move
in use or when cleaning. Do not
attempt to handle the appliance
until all parts have stopped
moving!
STEP 2:
Remove the cup/extractor blade
assembly from the motor base.
STEP 3:
Clean the individual components
(motor base, extractor blades,
NutriBullet
®
cups) as follows:
Cleaning the NutriBullet
®
is easy,
simply place any of the pieces
(except for the motor base and
extractor blade) on the TOP
RACK of the dishwasher or hand
wash with warm soapy water
and rinse.
• Regularly check the 3 tabs
on the side of the Cup
(cracking, crazing, breakage
or rounding). If damaged,
replace immediately to
prevent possible personal
injury.
• NEVER USE A CUP WITH A
BROKEN, DAMAGED, OR
MISSING TAB AS DOING SO
MAY CAUSE THE CUP AND
MOTOR BASE TO SEPARATE
EXPOSING THE BLADE
ASSEMBLY!
STUBBORN CLEAN UP:
• If ingredients dry inside the
NutriBullet
®
Cup, make your
cleanup a snap by filling the
cup about 2/3 full with room
temperature (21°C/70°F or
less) water and screw on
the extractor blade. Place
the cup/extractor blade
assembly on the NutriBullet
®
motor base for about 20-30
seconds. This will loosen the
stuck ingredients, and with a
light scrub and rinse, you’ll
be all finished.
EXTRACTOR BLADE:
• DO NOT REMOVE THE
GASKET as this will
permanently damage the
extractor blade and cause
leakage. If after washing as
indicated above additional
disinfecting is desired,
you may rinse with a 10%
vinegar/water solution or
with lemon juice. If, over
time, the gasket becomes
loose or damaged, you may
order a new extractor blade
at: bulletbrands.com.au
bulletbrands.co.nz
or contact Customer Service.
• Dry the extractor blade
completely. It is helpful to
turn the blade on its side in
your dish drainer to ensure
BOTH SIDES of the extractor
blade are completely dried.
NUTRIBULLET
®
CUPS
& TO-GO LIDS:
• These items are all TOP
RACK dishwasher safe. We
recommend rinsing them
and giving them a quick
brush with a dish brush to
remove any dried debris
before washing them in the
dishwasher. NEVER use the
sanitize cycle to wash the
Cups as this may warp the
plastic.
Replacement parts.
To order additional parts and
accessories, please visit our
website at:
bulletbrands.com.au
bulletbrands.co.nz.
Loading ...
Loading ...
Loading ...