Loading ...
Loading ...
Loading ...
3
*100% Jam Proof when used in accordance with user manual
Do nothing and
shredder will go
automatically to sleep
mode after 2 minutes
of inactivity
BASIC SHREDDING OPERATION
Press ( ) ON to activate
PAPER/CARD OR CD
Feed paper/card straight
into paper entry and
release
3
Plug in and put disconnect
power switch in ON
(I) position
To shred CDs or credit
card, rotate safety flap
into place
When finished
shredding set to
OFF (
)
or
or
7
4
AUTO
6
AUTO
2
Hold CD/card at edge,
and feed into center of
entry and release
5
7
Eliminates paper jams and powers through tough jobs.
JAM PROOF SYSTEM OPERATION*
Advanced Jam Prevention- Electronically
measures paper thickness to prevent paper jams:
Remove several sheets until
indicator is below red.
Continue 100% Jam
Proof Shredding
If a misfeed
occurs:
If
illuminates after paper has been
reversed, press reverse and remove paper.
Otherwise, regular shredding will resume.
1 2 3
Up to RED: Too many
sheets have been inserted.
Up to GREEN: More sheets
can be added.
Up to YELLOW: Productivity
is optimized.
All indicators light up and
shredder pauses for 3-6 seconds
Wait for flashing to stop after automatic correction
is complete. Regular shredding will resume.
ADVANCED PRODUCT FEATURES
WHEN IN SLEEP MODE
In sleep mode
To get out of sleep mode
touch control panel
insert paper
or
AUTO
1
2 3
SET-UP AND TESTING
Turn the shredder ON
( ) to activate SafeSense
®
Touch test area and
look for the SafeSense
®
indicator to illuminate
SafeSense
®
is active and
working properly
If hand is held on SafeSense
®
area more than 3 seconds
shredder will shut off
AUTO
1
2 43
SAFESENSE
®
TECHNOLOGY OPERATION
Stops shredding immediately when hands touch the paper opening.
Jam Proof System
Eliminates paper jams and
powers through tough jobs
Patented SafeSense
®
Technology
Stops shredding immediately when
hands touch the paper entry
Energy Savings System
Optimal energy efficiency 100% of the
time – in use and out of use.
• Saves energy in four ways: energy-efficient electronics, jam prevention,
standby mode and sleep mode.
• Sleep Mode shuts down shredder after 2 minutes of inactivity.
Optimal energy efficiency 100% of
the time – in use and out of use.
ENERGY SAVINGS SYSTEM
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com
1
CLEANING AUTO-START INFRARED SENSORS
PRODUCT MAINTENANCE
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run
even if there is no paper present
(Note: two paper detection sensors are located in the center of the paper entry).
TO CLEAN THE SENSORS
Turn off and unplug
shredder
Locate Auto-start
infrared sensor
Using cotton swab, wipe
away any contamination
from the paper sensors
Dip cotton swab in
rubbing alcohol
3
AUTO AUTO AUTO
1
2 4
ENGLISH
Models 125Ci/125i
All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive
noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you
empty your waste bin.
OILING SHREDDER
15
15
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
*Apply oil across entry
1
4
Press and hold forward
( ) 2-3 seconds
AUTO AUTO AUTO
2
TROUBLESHOOTING
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator
will remain illuminated and the shredder will not operate for the duration of the recovery time.
Bin Full: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36054.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Remove Paper: When illuminated, press reverse ( ) and remove paper. Reduce paper quantity to an acceptable amount and refeed into paper entry.
SafeSense
®
Indicator: If hands are too close to the paper entry, the SafeSense
®
indicator will illuminate and the shredder will stop shredding. If SafeSense
®
is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
Self Cleaning Cycle: Shredder periodically cycles in forward and reverse lasting 3-6 seconds (125Ci only).
Loading ...
Loading ...