Loading ...
Loading ...
Loading ...
OPERATION
1. Place the Heater on a firm, level surface, after assembling
per this manual.Plastic or rubber tabs, like the feet on this unit,
may stick to furniture surfaces and/or hardwood floors. The unit
may leave a residue that could darken, stain or leave permanent
blemishes on the finish of certain furniture surfaces, including
wood surfaces, and/or hardwood floors.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may
slip partially or completely out of the receptacle
with only the slight movement of the attached cord.
Receptacles in this condition may overheat and
pose a serious fire hazard; if covered by a curtain
or drape, the fire hazard is even greater.
3. When the Heater is initially plugged in, there will
be a “beep” and the Power Light will come on indicating that
there is power to the unit. The Power Light will remain lit until
the Heater is unplugged from the electrical outlet. (Figure 1)
4. Turn the Heater ON by pressing the Power Button ( ).
5. Press the ( ) and
( ) buttons at the same time to change the
display to ° Celsius. Press the same two buttons together again
to change the display back to ° Fahrenheit.
6. Upon turning the Heater on, the unit will be in HIGH heat (1500
Watts). (Figure 1)
7. Press the ( ) button for LOW heat.
8. To turn the Heater OFF, press the Power Button ( ) and unplug
the Heater from the electrical outlet.
OSCILLATION:
Pressing the Oscillation Button ( ) will allow the Heater to oscil-
late back and forth. To stop the oscillation, press the Oscillation
Button ( ) again. When the Heater is in Automatic Temperature
Control, the oscillation function will stop when the set temperature
is reached and resume when the Heater turns back on.
NEW 4/14
4
CT32950ES
NEW 4/14
9
CT32950ES
MODEL CT32950
MODELO CT32950
TIMER FUNCTION
(Figure 2)
The timer function may be activated when the Heater display is in
any function or speed. This function allows you to set the length
of time the Heater will run before turning itself off, from 1 hour to
8 hours. Pressing the Timer Button ( ) will increase the length of
time by 1 hour each time this button is pressed. After the display
reflects 8 hours, pressing the Timer Button ( ) once more will reset
the Heater to run continuously. The Heater will turn off when the
set time has elapsed. The unit can be turned back on by pressing
the Power Button ( ).
ARMADO
(Figuras 1 a 2)
No se requieren herramientas.
Cuidadosamente retire el Calentador de la bolsa y de la caja de
cartón.
Para facilitar el ensamblaje, apoye el Calentador de modo tal que
la parrilla frontal y el panel de control apunten hacia arriba.
1. Ensamble la base al encajar el lado A y el lado B como se
muestra en la Figura 1.
Timer Function in
Low Heat
Timer Function in
High Heat and Automatic
Temperature Control
Figure 2
Display when initially turned on
Figure 1
AUTOMATIC TEMPERATURE CONTROL
The automatic temperature function will only operate on "High"
heat. You cannot set the temperature automatically when the
unit is in the low heat mode.
1. To set the room at a specific temperature press the ( ) or
( )
buttons to the desired temperature. The display will now reflect
the ( ) and the temperature will be flashing. The Heater is now
in Auto Temperature Mode.
2. When you reach the temperature at which you want to set the
unit, the set temperature will flash several times and then the
display will return to indicate the current room temperature and
will gradually change as the room temperature changes. NOTE:
the temperature display does not indicate the temperature of
the heated air being emitted by the heater.
3. Once the room temperature reaches 2 degrees above the set
temperature, the Heater will shut off. Once the room tempera-
ture reaches 1 degree below the set temperature, the Heater
will turn back on and continue to cycle off and on to maintain
the set temperature.
4. This function will cancel if the ( ) button is pressed. The Heater
will now be in High heat and run continuously.
NOTE: It is normal for the Heater “fan” to run for approximately 15
seconds when the Heater shuts off after reaching the set
temperature.
Figure 3
Figura 1
Figura 2
2. Conecte la base a la parte inferior del Calentador. Intro-
duzca el cable eléctrico a través del orificio grande en el
ensamblaje de la base. NOTA: El canal para el cable en la
parte inferior de la base debe quedar hacia la parte trasera
del calentador. (Figura 2)
3. Mediante el uso de 4 tornillos de apriete manual, fije la Base
al Calentador como se muestra en la Figura 2.
Display reflects High Heat and
Automatic Temperature Control Function
Figure 3
Loading ...
Loading ...
Loading ...