Loading ...
Loading ...
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in this instruction
manual.
3. To protect against electrical shock do not immerse unit,
plug, or cord in water, or spray with liquids and plug the
appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving fan
from one location to another, before putting on or
taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. Do not operate in the presence of explosive and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under rugs
or any parts near an open flame, cooking or other
heating appliance.
9. Do not operate any appliance with a damaged cord or
plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
contact customer service for examination and/or repair.
10. Do not run cord under carpeting. Do not cover cord with
throw rugs, runner, or similar coverings. Do not route
cord under furniture or appliances. Arrange cord away
from traffic area and where it will not be tripped over.
11. The use of attachments not recommended or sold by the
appliance manufacturer may cause hazards.
12. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13. Do not use outdoors.
14. To disconnect, grip plug and pull from wall outlet. Never
yank on cord.
15. Always use on a dry, level surface.
16. Do not operate fan until fully assembled with all parts
properly in place.
17. This product is intended for household use ONLY and not
for commercial or industrial applications.
18. WARNING: To reduce the risk of electrical shock and
injury to persons, do not use in window.
19. WARNING: To reduce the risk of fire or electric shock,
do not use this fan with any solid-state speed control
device.
20. This product employs overload protection (fuse). A
blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from the
outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse
blows, a short circuit may be present and the product
should be discarded or customer service should be
contacted for examination and/or repair.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
FEATURES - OPERATIONS
CLEANING
Figure 1
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in
a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
D. Motor Housing
E. Oscillation Control
F. Speed Control Knob
E
F
D
Figure 2
ADJUSTMENT INSTRUCTIONS
VERTICAL ANGLE ADJUSTMENT – Loosen Tilt Adjustment
Knob, hold the fan base, and gently move the motor
housing up or down to the desired vertical angle. Lastly, be
sure to firmly tighten the Tilt Adjustment Knob to keep the
fan head in place.
OSCILLATION CONTROL – The oscillation control bar is
located on the top of the motor housing. Push the control
bar down for oscillation, pull up for operation in a
stationary position.
CLEANING/MAINTENANCE INSTRUCTIONS
Follow these instructions to correctly and safely care for
your table fan.
REPLACEABLE FUSE
If your (5 Amp, 125 Volt) replaceable fuse blows, please
visit our website at www.getholmesfans.com for information
on how to order a new fuse. Follow the user servicing
instructions to replace the fuse on the plug.
ASSEMBLY INSTRUCTIONS
Your Table Fan comes completely assembled and is ready
for immediate use. Carefully unpack your fan, refer to the
operating instructions and enjoy!
OPERATING INSTRUCTIONS
Step 1: Set fan on a dry, level surface.
Step 2: Please make sure the Speed Control Knob is in the
Off(0) position. Plug cord into any standard
120 volt AC outlet.
Step 3: The Speed Control Knob is located on the
back of the Fan Motor Housing. The speed is
adjusted by turning the Speed Control Knob
to the desired setting, 0-II-I.
User Servicing Instructions
1. Unplug your fan. Grasp plug and remove from the
receptacle or other outlet device. Do not unplug by
pulling on cord.
2. Open fuse cover, located on the top of the plug, by
using your thumb or a flathead screwdriver to slide the
cover down towards the prongs.
NOTE: Ensure that fuse cover is completely open
before attempting to
remove fuse.
3. Remove fuse carefully by
using a small screwdriver
to pry the fuse out of the
compartment by the
metal ends of the fuse.
(see Figure 3)
4. Place plug on a solid, flat
surface. Insert new 5 Amp, 125 Volt fuse into fuse
compartment and use a small screwdriver to secure
the metal ends of the fuse into the compartment.
CAUTION: Risk of fire. Replace fuse only with
5 Amp, 125 Volt fuse.
5. Slide fuse cover closed completely. If fuse cover is
difficult to close, make sure fuse is secured in place
completely by pressing down on metal ends of the fuse.
6. Risk of fire. Do not replace attachment plug. Contains
a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
Figure 3
Fuse
Metal ends
Fuse cover
A. Fan Hub
B. Fan Base
C. Tilt Adjustment Knob
A
B
C
Loading ...