Loading ...
Loading ...
Loading ...
11
ENGLISH
Repairs
The charger and batteries are notserviceable. There are no
serviceable parts inside the charger or batterypack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a DeWALT factory service center or a
DeWALT authorized service center. Always use identical
replacementparts.
Accessory/replacement collets
Sold Separately
• 1/8" (3mm) ‑ DCE55018
• 5/32" (4mm) ‑ DCE550532
• 1/4" (6mm) ‑ DCE55014
Tool Connect™ Chip (Fig. J)
Optional Accessory
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
moreinformation.
Installing the Tool Connect™ Chip
1. Remove the retaining screws
20
that hold the Tool
Connect™ Chip protective cover
19
into thetool.
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
13
.
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
thescrews.
4. Refer to Tool Connect™ Chip Instruction Sheet for
furtherinstructions.
Accessories
WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product,
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only DeWALT
recommended accessories should be used with
thisproduct.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact DeWALT call 1-800-4-DeWALT
(1-800-433-9258) or visit our website: www.dewalt.com.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing thisprocedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regularcleaning.
Cutting a Hole for an Electrical Outlet
(Fig. G)
WARNING: Shut off all live electric circuits to any areas
where cut‑outs will bemade.
1. Push any wiring deeply into the outlet box to avoid
damage from the cuttingbit.
2. Before hanging the sheet covering the fixture box, mark
the approximate location of the center of the fixture
box on the wall board. Check the cutting bit depth
against the side of the board to be sure it will cut entirely
through thematerial.
3. Tack the sheet in place with a few fasteners avoiding the
stud holding the fixture box. This allows the wall board to
flex slightly around the protruding fixturebox.
4. Turn the cut‑out tool on. Holding the tool firmly with
both hands, plunge the bit straight into the center of the
fixturebox.
5. Cut to the right until the bit reaches the inside edge of
the fixture box. Pull the bit out just enough it to clear the
edge of the fixture box. Plunge the bit in again, holding
the bit gently against the outside of the fixture box.
6. Follow the outside of the fixture box and complete the
cut counterclockwise, keeping slight pressure against the
fixture box. This will minimize wandering and give you a
clean, precisecut.
7. Remove the waste and dust from the fixture box. Finish
fastening the sheet of wallboard.
• Do not cut material lying on a hard surface. Clearance
behind material to be cut must be allowed for
protrudingbit.
• Disconnect battery from tool before making adjustments,
changing bits, or cleaningtool.
• Do not start the tool with bit engaged in the material.
The bit may grab thematerial.
Loading ...
Loading ...
Loading ...