1. Home
  2. Craftsman
  3. Craftsman CMCF940M1 User Manual
  4. Page 10

Craftsman CMCF940M1 1/2" (13 mm) 20V Max* Cordless Impact Wrench

INSTRUCTION MANUAL - Page 10

For CMCF940M1.

PDF File Manual, 32 pages, Read Online | Download pdf file

CMCF940M1 photo
Loading ...
Loading ...
Loading ...
ENGLISH
8
Forward/Reverse Control Button (Fig.A)
A forward/reverse control button
2
determines the direction
of the tool and also serves as a lock-offbutton.
To select forward rotation, release the trigger switch and
depress the forward/reverse control button on the right side
of thetool.
To select reverse, release the trigger switch and depress the
forward/reverse control button on the left side of thetool.
The center position of the control button locks the tool in
the off position. When changing the position of the control
button, be sure the trigger isreleased.
NOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start up. This is
normal and does not indicate aproblem.
Proper hand position requires one hand on the main
handle
4
.
Proper Hand Position (Fig.A, F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Installing and Removing the Battery Pack
(Fig.K)
WARNING: Ensure the tool/appliance is in the off
position before inserting the batterypack.
NOTE: For best results, make sure your battery pack is
fullycharged.
To install the battery pack
6
into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does notdisengage.
To remove the battery pack from the tool, press the release
button
5
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of thismanual.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
1. Place the switch in the locked off (center) position or
remove battery pack before changingaccessories.
2. To install an accessory on the anvil, firmly push accessory
onto the anvil
3
.
NOTE: The hog ring
8
compresses to allow the accessory
to slide on. After the accessory is installed, the hog ring
applies pressure to help provide accessoryretention.
3. To remove an accessory, grasp the accessory and firmly
pull itoff.
Anvil (Fig.A)
WARNING: Use only impact accessories. Non‑impact
accessories may break and cause a hazardous
condition. Inspect accessory prior to use to ensure that
it contains nocracks.
CAUTION: Inspect anvils, and hog rings prior to
use. Missing or damaged items should be replaced
beforeuse.
Your impact tool can generate the following maximum
torque values (Speed 1, Speed 2, Speed 3).
NOTE: Output torque is dependent on the speed selected,
with the highest provided in Speed 3.
TOOL SPEED
Output Torque
CMCF940 SPEED 1 100 Ft. Lbs. / 130 Nm
SPEED 2 300 Ft. Lbs. / 400 Nm
SPEED 3 700 Ft. Lbs. / 950 Nm
Speed Selector (Fig.A)
Your tool is equipped with a speed selector
9
which allows
you to select one of three speeds. Select the speed based on
the application and control the speed of the tool using the
variable speed trigger switch
1
.
SPEED 1 0–450 rpm
SPEED 2 0–1200 rpm
SPEED 3 0–2000 rpm
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in theslots.
NOTE: Do not attempt to mount CMCB101 charger under a
bench ortable.
NOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward theceiling.
VersaTrack™
WARNING: Do not charge batteries while charger is
hung onTrackwall.
CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for furtherinformation.
NOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwallcompatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Loading ...
Loading ...
Loading ...