Loading ...
Loading ...
Loading ...
40
OPERACIÓN
Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto.
Aprenda y comprenda sus significados.
ESTRANGU-
LACIÓN RÁPIDO LENTOMARCHA
ATRÁS NEUTRO ALTO BAJO
MARCHA
ATRÁS MARCHA
HACIA
ADELANTE
COMBUS-
TIBLE
MOTOR
APAGADO ALTURA
DE LA
SEGADORA
MOTOR
ENCENDIDO
MOTOR
EN MARCHA
BATERÍA
LEVANTA-
MIENTO DE
LA SEGADORA
SISTEMA
FUNCIONAMIENTO
ATRÁS (ROS)
LUCES
ENSENDIDAS
INTERRUPTOR
DE IGNICIÓN
PEDAL DE
FRENO /
EMBRAGUE
PALANCA DE
MANDO CRUCERO
FRENO DE
ESTACION-
AMIENTO
RUEDA LIBRE
(Solamente para los
modelos automatico)
No seguir las siguientes
instrucciones puede provocar
heridas o muerte. Los símbolos
de aviso de seguridadse utilizan
para identificar informaciones de
seguridad relativas a peligros que
pueden provocar la muerte, heridas
graves y/o daños a la máquina.
PELIGRO indica un peligro que, si no se evita,
provoca muerte o lesiones graves.
ADVERTENCIA indica un peligro que, si no se evita,
puede provocar muerte o lesiones graves.
PRECAUCIÓN indica un peligro que, si no se evita,
puede provocar lesiones ligeras o moderadas.
PRECAUCIÓN cuando se utiliza sin el símbolo de
aviso, indica una situación que puede provocar
daños al tractor y/o al motor.
FUEGO indica un peligro que, si no se evita, puede
provocar la muerte, lesiones graves y/o danos
a la máquina.
SUPERFICIES CALIENTES indica un peligro que,
si no se evita, puede provocar la muerte, lesiones
graves y/o danos a la máquina.
EL CIERRE
DIFERENCIAL
PROTECCIÓN
DE OÍDO SE
REQUIERE
PELIGRO, GUARDE
LAS MANOS Y
LOS PIES LEJOS
15
15
MANTENGA EL
AREA DESPEJADA
PELIGROS DE
PENDIENTES
(VEA LA SECCIÓN DE LAS REGLAS DE SEGURIDAD)
ACCESORIO
DEL EMBRAGUE
ENGANCHADO
ACCESORIO
DEL EMBRAGUE
DESENGANCHADO
25
00663
Retaining
Ring
Washers
Axle Cover Square Key (Rear
Wheel Only)
TO REMOVE WHEEL FOR REPAIRS
1. Block up axle securely.
2. Remove axle cover, retaining ring and
washers to allow wheel removal (rear
wheels have a square key - Do not lose).
3. Repair tire and reassemble.
NOTE: On rear wheels only: align grooves in
rear wheel hub and axle. Insert square key.
4. Replace washers and snap retaining ring
securely in axle groove.
5. Replace axle cover.
NOTE: To seal tire punctures and pre vent
flat tires due to slow leaks, purchase and
use tire sealant from Sears. Tire sealant also
pre vents tire dry rot and corrosion.
Weak or Dead
Battery Fully Charged
Battery
TO START ENGINE WITH A WEAK BAT-
TERY
WARNING: Lead-acid batteries gen er-
ate ex plo sive gases. Keep sparks, flame
and smoking ma te ri als away from bat ter ies.
Always wear eye pro tec tion when around
batteries.
If your battery is too weak to start the engine,
it should be recharged. (See "BATTERY" in
the MAINTENANCE section of this man u al).
If “jumper ca bles” are used for emer gen cy
starting, follow this pro ce dure:
IMPORTANT: Your tractor is equipped with
a 12 volt system. The other vehicle must also
be a 12 volt system. Do not use your tractor
battery to start other vehicles.
TO ATTACH JUMPER CABLES -
1. Connect one end of the RED cable to the
POSITIVE (+) terminal of each battery(A-
B), taking care not to short against tractor
chassis.
2. Connect one end of the BLACK ca ble
to the NEGA TIVE (-) terminal (C) of fully
charged battery.
3. Connect the other end of the BLACK
cable (D) to good chassis ground, away
from fuel tank and bat tery.
TO REMOVE CABLES, REVERSE ORDER
-
1. BLACK cable first from chassis and then
from the fully charged battery.
2. RED cable last from both batteries.
FRONT WHEEL TOE-IN/CAM BER
Your new tractor front wheel toe-in and
camber is set at the factory and is normal.
The front wheel toe-in and camber are not
adjustable. If damage has occurred to
affect the factory set front wheel toe-in or
camber, contact a Sears or other qualified
service center.
02239
Adjustment Bolt
Neutral
Lock
Gate
Gearshift Lever
TRANSAXLE GEAR SHIFT LEVER NEU-
TRAL ADJUSTMENT
The transaxle should be in neutral when the
gear shift lever is in neutral (N) (lock gate)
position. The adjustment is preset at the
factory; however, if adjustment is needed,
proceed as follows:
1. Ensure transaxle is in neutral (N).
NOTE: When the tractor rear wheels move
freely, the transaxle is in neu tral.
2. Loosen adjustment bolt in front of the
right rear wheel.
3. Position the gear shift lever in the neutral
(N) position.
4. Tighten adjustment bolt securely.
NOTE: If additional clearance is needed to
get to ad just ment bolt, move mower deck
height to the lowest position.
Loading ...
Loading ...
Loading ...