P3
www.bromic.com
P3
SEL *
1 2 3 4 5 6
SEL
Heater 100% - Heater output at full (100%)
Heater 66% - Heater output at 66% of total
Heater 33% - Heater output at 33% of total
Heater OFF - Heater off
Lights 100% (DIM˄) - Lights output at full (100%) or HOLD to DIM Up
Lights 50% - Light output at 50% of total
Lights OFF (DIM˅) - Light off or HOLD to DIM Down
SEL button:
multi-remote function
Press the SEL buttons from left or right
in order to select design zone.
BROMIC SMART-HEAT™
WIRELESS REMOTES
BY BROMIC
USER MANUAL
DESCRIPTION OF THE PRODUCT
UHF band remote with PLL controlled carrier frequency.
This type of remote is used for controlling devices for
domestic use, automatic openings, ON-OFF light control,
dimming, etc. This appliance transmits a rolling code type
signal to prevent duplication and guarantee maximum
secrecy. The remote code can be stored in the receiver
directly via the latter or via radio from the remote. With
the second possibility you can add new remotes to an
existing system without having to touch the receiver. This
can be done directly by the end user (the installer’s help is
not required). The code is stored in the receiver’s EEPROM
memory that retains it even if power is cut temporarily.
SAFETY RULES
• Do not use the manual remote in places or where
systems are sensitive to radio emissions (e.g. airports,
hospitals).
• Keep the remote out of the reach of children and
animals.
• Do not keep or use the remote in places that are damp,
where there is steam, high air humidity, dust or where
it is exposed to the direct rays of the sun or similar
environmental conditions.
• Do not let the remote drop: it could be damaged or its
range of action reduced.
• Changes or modification not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
USE
• The operator is in no way protected against interference
from other telecommunication equipment or systems
(e.g. authorised radio systems working on the same
frequency range).
• If you are having problems with its range of action, fix
the remote up high. Change the battery if necessary.
CHANGING THE BATTERY - BATTERY IS HAZARDOUS
• WARNING: Keep the batteries out of the reach of
children, whether new or used.
• If swallowed, the lithium button battery can cause
severe or fatal injuries in 2 hours or less if it is swallowed
or placed inside any part of the body.
• Medical attention should be sought immediately if it is
suspected the battery has been swallowed or placed
inside any part of the body
• Explosion hazard if the battery is substituted incorrectly.
• Replace the battery with a CR 2430 type battery only.
• Always wrap the battery up, both when it is being
stored and when it is being disposed of. The battery
should not come into contact with other metal objects
as it could cause the battery to run down, catch fire or
be damaged.
• Dispose of damaged or finished batteries immediately
in compliance with the law. To this end, contact the
authorities for safeguarding the environment or the
centre for disposing of waste materials in your area.
• Do not throw the battery away with household rubbish.
1. Open the back cover (manual remote) or the
battery housing (wall remote).
2. Take the old battery out and put the new one in the
same way.
Pay attention to correct polarity (+/-)!
REMOTE FIXING
If the remote is fixed on the wall with biadhesive,
the maximum holding will be reached after 24
hours from the application. Application temperature
min.+10°C (50°F).
GUARANTEE
The guarantee complies with the law. If the guarantee
has to be used please refer to the specialized retailer.
The right to the guarantee is applicable only for the
country in which the manual remote was purchased.
The batteries are not covered by the guarantee.
HOW TO STORE A REMOTE VIA RADIO WITHOUT
ACCESSING THE RECEIVER BY MEANS OF A
PREVIOUSLY STORED REMOTE
• Press the P3 button inside the already programmed
remote. The active receiver will sound continuously.
If there is no sound, the remote is not programmed
into the receiver.
• Within 5 seconds, press a button of the already
programmed remote, relative to the function to
copy. The sound will be interrupted, and continue
for another 5 seconds.
• During the sound, press a button of the new remote
that requires to be programmed. The programming
is indicated by an intermittent sound.
CONFORMITY
Bromic declares that the remotes supplied satisfy the
following technical regulations:
• FCC (Federal Communications Commission) Part
15 (FCC ID: P59TVTXI916S; P59TVEVO916S)
• IC (Industry Canada) RSS-102
(IC: 11242A-TVTXI916S; IC: 11242A-TVEVO916S)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Model Dimmer-Remote On/O-Remote
Dimmer-Master (42) Wireless
Remote
Carrier Frequency 916MHz (US/AU) / 868.3MHz (EU)
Modulation FSK
Power Supply
3V ±10%
CR2430 battery
Consumption when
transmitting
10mA
Working Temperature -10+55°C / 14+131°F
Range 30m / 100ft
DIMMER MASTER (42)
WIRELESS REMOTE
TECHNICAL DATA
The manufacturer programs each individual remote with a unique code
DIMMER REMOTE ON/OFF REMOTE
DIM+
DIM-
OFF
100%
75%
50%
Min.
ON (1)
OFF (1)
ON (2)
OFF (2)
Keep the remote away
from Children!
Version 1.2
