Loading ...
Loading ...
CUTTING SAFETY
_,WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
• Use only for trimming, scalping, mowing and
sweeping. Do not use for edging, pruning or
hedge trimming.
• Keep firm footing and balance. Do not over-
reach.
• Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level. A hot muffler can cause serious bums.
• CL_from your right to your left. Cutting on left
side of the shield will throw debris away from
the operaton
• Use only in daylight or good artificial light.
• Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
• Allow engine to cool; secure unit before stor-
ing or transporting in vehicle.
• Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left inthe carbure-
tor by starting the engine and letting itrun until
it stops.
• Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
• Store unit so line limiter blade cannot acciden-
tally cause injury. The unit can be hung by the
tube.
• Store unit OL_of reach of children.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age inotherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti-vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with asparkarresting screen. Ifyou
operate ine locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by your autho-
rized service dealer.
£=
II.WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners ere secure.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
ADJUSTING THE HANDLE
_WARNING: When adjusting the han-
dle, be sure it remains between the trigger
and the safety label.
1. Loosen wing nut on handle.
2. Rotate the handle on the tube to an upright
position; retighten wing nL_.
ATTACHING SHIELD
_,WARNING: The shield must be prop-
edy installed. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can CL_yOU.
For proper orientation of shield, see KNOW
YOUR TRIMMER illustration in OPERATION
section. Assemble your shield as shown.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole in
bracket.
4. Securely tighten wing nL_onto bolt.
Shield %
Line Limiter Blade
Slot
/
Bracket
Wing
Nut
3
Loading ...
Loading ...
Loading ...