Stage & Studio Power Sequence Conditioner
PS1000 - PS1200
Pro Audio AV Digital Power Sequencer Controller
with Voltage & Temperature Readout, Rack Mount
www.PyleUSA.com
1
www.PyleUSA.com
2
CAUTION!
RISK OF ELECTRIC SHOCK. DO NOT OPEN
TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DISCONNECT POWER CORD BEFORE REMOVING BACK PANEL COVER
TO ACCESS GAIN SWITCH.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
MAGNETIC FIELD
CAUTION! Do not locate sensitive high-gain equipment such as preampliers or
tape decks directly above or below the unit. Because this amplier has a high
power density, it has a strong magnetic eld which can induce hum into
unshielded devices that are located nearby. The eld is strongest just above and
below the unit. If an equipment rack is used, we recommend locating the
amplier(s) in the bottom of the rack and the preamplier or other sensitive
equipment at the top.
WATCH FOR THESE SYMBOLS:
The exclamation point triangle is used to alert the user
to important operating or maintenance instructions.
The lightning bolt triangle is used to alert the user to
the risk of electric shock.
Introduction & Features
This amazing professional audio processor has a built-in high performance Micro
Controller for precise electrical timing. This unit provides clean lters AC power
with built in two stage EMI lter for each output. 8 channel cut-switch rear panel
American Standard outputs and 1 constant un-switched front panel.
Other voltage outputs: 1 DC 12 Volt. You can link more than 100 units together
with automatic master unit display. The display shows AC voltage, ambient
temperature, wiring and ground status all in real time. 8 Segment display for
step Time and various LEDs cover output, master, bypass, power, voltage and
sequence.
Front Panel Introduction
1. Outlet Sequence Power ON/OFF: Push up or down to start the sequence
switch ON or OFF automatically one by one.
2. LED For Sequence Power ON/OFF
3. DISPLAY WINDOW: Displays voltage or temperature (both in Fahrenheit &
Centigrade)
4. Temperature: Adjust the temperature slightly if the real display is dierent
from the real one.
5. Mode Select: Button switch for Fahrenheit/Centigrade temperature or
Voltage display on the LED window.
6. BYPASS Switch: Push to make all the outlets work at one time. Can't be
adjusted by other control.
7. CH 1 Only: After starting the power sequence, control only the Ch1 ON or OFF.
www.PyleUSA.com
1
www.PyleUSA.com
2
CAUTION!
RISK OF ELECTRIC SHOCK. DO NOT OPEN
TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DISCONNECT POWER CORD BEFORE REMOVING BACK PANEL COVER
TO ACCESS GAIN SWITCH.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
MAGNETIC FIELD
CAUTION! Do not locate sensitive high-gain equipment such as preampliers or
tape decks directly above or below the unit. Because this amplier has a high
power density, it has a strong magnetic eld which can induce hum into
unshielded devices that are located nearby. The eld is strongest just above and
below the unit. If an equipment rack is used, we recommend locating the
amplier(s) in the bottom of the rack and the preamplier or other sensitive
equipment at the top.
WATCH FOR THESE SYMBOLS:
The exclamation point triangle is used to alert the user
to important operating or maintenance instructions.
The lightning bolt triangle is used to alert the user to
the risk of electric shock.
Introduction & Features
This amazing professional audio processor has a built-in high performance Micro
Controller for precise electrical timing. This unit provides clean lters AC power
with built in two stage EMI lter for each output. 8 channel cut-switch rear panel
American Standard outputs and 1 constant un-switched front panel.
Other voltage outputs: 1 DC 12 Volt. You can link more than 100 units together
with automatic master unit display. The display shows AC voltage, ambient
temperature, wiring and ground status all in real time. 8 Segment display for
step Time and various LEDs cover output, master, bypass, power, voltage and
sequence.
Front Panel Introduction
1. Outlet Sequence Power ON/OFF: Push up or down to start the sequence
switch ON or OFF automatically one by one.
2. LED For Sequence Power ON/OFF
3. DISPLAY WINDOW: Displays voltage or temperature (both in Fahrenheit &
Centigrade)
4. Temperature: Adjust the temperature slightly if the real display is dierent
from the real one.
5. Mode Select: Button switch for Fahrenheit/Centigrade temperature or
Voltage display on the LED window.
6. BYPASS Switch: Push to make all the outlets work at one time. Can't be
adjusted by other control.
7. CH 1 Only: After starting the power sequence, control only the Ch1 ON or OFF.
8. One touch ON/OFF key and LED: Press to power ON/OFF. The LED indicates
the related outlet's status.
9. Internal delay time selector: Choose the internal power sequence delay
time: 0.5 seconds or 2 seconds.
10. USB Charge (5V/2A): Charge for Mobile phone (5VI2A) each.
11. Power switch for the assistance light: Power ON/OFF the light according to
the switch position.
12. Assistance light connector: This is BNC connector, it can supply 12V/0.5A
power, use a gooseneck light to connect.
13. Always Power Outlet: Assistant power outlet, connects to the AC input
directly, power always valid.
Rear Panel Introduction
1. Main power supply with standard American plug
2. Input Voltage Selective: Power Supply Switch at 115V/60Hz or 230V/50Hz
3. Outlets OUT1-OUT8: Power outlet can carry 15AMP (RMS) each outlet,
otherwise the unit is not safe.
4. Remote Control link: You can set a extra switch to replace the power switch
to achieve the long distance control.
5. LED for remote control: Indicates the unit status, use it with Remote control.
6. Link out: Many unit works via link, if you want to link next unit, the lower unit
should be connected here.
7. Link in: Many unit works via link, if you need to link up, then the upper unit
should be connected here.
www.PyleUSA.com
3
www.PyleUSA.com
4
BlOCK DIAGRAM
Filter Schematic Diagram
8. One touch ON/OFF key and LED: Press to power ON/OFF. The LED indicates
the related outlet's status.
9. Internal delay time selector: Choose the internal power sequence delay
time: 0.5 seconds or 2 seconds.
10. USB Charge (5V/2A): Charge for Mobile phone (5VI2A) each.
11. Power switch for the assistance light: Power ON/OFF the light according to
the switch position.
12. Assistance light connector: This is BNC connector, it can supply 12V/0.5A
power, use a gooseneck light to connect.
13. Always Power Outlet: Assistant power outlet, connects to the AC input
directly, power always valid.
Rear Panel Introduction
1. Main power supply with standard American plug
2. Input Voltage Selective: Power Supply Switch at 115V/60Hz or 230V/50Hz
3. Outlets OUT1-OUT8: Power outlet can carry 15AMP (RMS) each outlet,
otherwise the unit is not safe.
4. Remote Control link: You can set a extra switch to replace the power switch
to achieve the long distance control.
5. LED for remote control: Indicates the unit status, use it with Remote control.
6. Link out: Many unit works via link, if you want to link next unit, the lower unit
should be connected here.
7. Link in: Many unit works via link, if you need to link up, then the upper unit
should be connected here.
www.PyleUSA.com
3
www.PyleUSA.com
4
BlOCK DIAGRAM
Filter Schematic Diagram
www.PyleUSA.com
5
www.PyleUSA.com
6
Remote Control Link Diagram
www.PyleUSA.com
5
www.PyleUSA.com
6
Remote Control Link Diagram
www.PyleUSA.com
7
www.PyleUSA.com
8
PS1200
Features:
• Power Supply Controller Sequencer System
• Audio Video (A/V) Power Conditioner
• Lab Tested Pro Audio Stage & Studio Performance
• Power Filter with 2-Stage High-Insert Dissipation
• Ensures the Safety of Electrical Equipment with Clean AC Power
• Noise/Interference/Distortion Eliminator Circuitry
• Integrated Micro-Controller for Displaying Precise AC Voltage and Ambient
Temperature
• Independent Outlet Power Cut-O Switch Control
• (8) Worldwide/EU Power Outlets on Rear Panel
• Selectable Power Sequence Switch Time
• Step Time Display in 8 Segment LED
• Sequence Switch LED
• Dual USB Device Charge Ports
• Digital LED Display with Real-time Data Readout
• Front Panel Continuous ‘Unswitched’ Power Outlet
• Control Signal Link Connection
• Built-in Safety, Spike & Surge Overload Protection
• Multiple Unit Compatible Series Link Support
• Ability to Series Link Over 100+ Units
• LED Indicator Lights for Each Output on Front Panel
What’s in the Box:
• Pro Audio Power Conditioner
• Link Cable: 6.6 ft.
Technical Specs:
• Outlet Type: (8) Channel Worldwide/EU Standard Power Outlets
• Output Power: 2200 Watt MAX
• Link Connector: S-Video, 4-Pin
• Sequence Switch Time Selectable: 2 Seconds / 0.5 Seconds
• Selectable Temperature Unit Readout: Fahrenheit / Celsius
• BNC Connector: 12V/0.5 Amp
• MAX Output Current: 15 Amp RMS
• MAX Output Voltage: 275 Volt
• Power Cable Length: 5.9’ ft. (14 AWG)
• USB Power: 5V/2A (x2)
• Power Supply: 115/230V, Switchable
• Dimensions (L x W x H): 19.0’’ x 8.1’’ x 2.1’’ -inches
PS1000
Features:
• Power Supply Controller Sequencer System
• Audio Video (A/V) Power Conditioner
• Lab Tested Pro Audio Stage & Studio Performance
• Power Filter with 2-Stage High-Insert Dissipation
• Ensures the Safety of Electrical Equipment with Clean AC Power
• Noise/Interference/Distortion Eliminator Circuitry
• Integrated Micro-Controller for Precise AC Voltage and Ambient Temperature
• Independent Outlet Power Cut-O Switch Control
• (8) US Standard Power Outlets On Rear Panel
• Selectable Power Sequence Switch Time
• Step Time Display in 8 Segment LED
• Sequence Switch LED
• Dual USB Device Charge Ports
• Digital LED Display with Real-time Data Readout
• Front Panel Continuous ‘Unswitched’ Power Outlet
• Control Signal Link Connection
• Built-in Safety, Spike & Surge Overload Protection
• Multiple Unit Compatible Series Link Support
• Ability to Series Link Over 100+ Units
• LED Indicator Lights for Each Output on Front Panel
What’s in the Box:
• Pro Audio Power Conditioner
• Link Cable: 6.6 ft.
Technical Specs:
• Outlet Type: (8) US Standard Power Outlets
• Output Power: 2200 Watt MAX
• Rack Mount Size: 1U
• Link Connector: S-Video, 4-Pin
• Sequence Switch Time Selectable: 2 Seconds / 0.5 Seconds
• Selectable Temperature Unit Readout: Fahrenheit / Celsius
• BNC Connector: 12V/0.5 Amp
• MAX Output Current: 15 Amp RMS
• MAX Output Voltage: 275 Volt
• Power Cable Length: 5.9’ ft. (14 AWG)
• USB Power: 5V/2A (x2)
• Power Supply: 115/230V, Switchable
• Dimensions (L x W x H): 19.0’’ x 8.1’’ x 1.7’’ -inches
www.PyleUSA.com
7
www.PyleUSA.com
8
PS1200
Features:
• Power Supply Controller Sequencer System
• Audio Video (A/V) Power Conditioner
• Lab Tested Pro Audio Stage & Studio Performance
• Power Filter with 2-Stage High-Insert Dissipation
• Ensures the Safety of Electrical Equipment with Clean AC Power
• Noise/Interference/Distortion Eliminator Circuitry
• Integrated Micro-Controller for Displaying Precise AC Voltage and Ambient
Temperature
• Independent Outlet Power Cut-O Switch Control
• (8) Worldwide/EU Power Outlets on Rear Panel
• Selectable Power Sequence Switch Time
• Step Time Display in 8 Segment LED
• Sequence Switch LED
• Dual USB Device Charge Ports
• Digital LED Display with Real-time Data Readout
• Front Panel Continuous ‘Unswitched’ Power Outlet
• Control Signal Link Connection
• Built-in Safety, Spike & Surge Overload Protection
• Multiple Unit Compatible Series Link Support
• Ability to Series Link Over 100+ Units
• LED Indicator Lights for Each Output on Front Panel
What’s in the Box:
• Pro Audio Power Conditioner
• Link Cable: 6.6 ft.
Technical Specs:
• Outlet Type: (8) Channel Worldwide/EU Standard Power Outlets
• Output Power: 2200 Watt MAX
• Link Connector: S-Video, 4-Pin
• Sequence Switch Time Selectable: 2 Seconds / 0.5 Seconds
• Selectable Temperature Unit Readout: Fahrenheit / Celsius
• BNC Connector: 12V/0.5 Amp
• MAX Output Current: 15 Amp RMS
• MAX Output Voltage: 275 Volt
• Power Cable Length: 5.9’ ft. (14 AWG)
• USB Power: 5V/2A (x2)
• Power Supply: 115/230V, Switchable
• Dimensions (L x W x H): 19.0’’ x 8.1’’ x 2.1’’ -inches
PS1000
Features:
• Power Supply Controller Sequencer System
• Audio Video (A/V) Power Conditioner
• Lab Tested Pro Audio Stage & Studio Performance
• Power Filter with 2-Stage High-Insert Dissipation
• Ensures the Safety of Electrical Equipment with Clean AC Power
• Noise/Interference/Distortion Eliminator Circuitry
• Integrated Micro-Controller for Precise AC Voltage and Ambient Temperature
• Independent Outlet Power Cut-O Switch Control
• (8) US Standard Power Outlets On Rear Panel
• Selectable Power Sequence Switch Time
• Step Time Display in 8 Segment LED
• Sequence Switch LED
• Dual USB Device Charge Ports
• Digital LED Display with Real-time Data Readout
• Front Panel Continuous ‘Unswitched’ Power Outlet
• Control Signal Link Connection
• Built-in Safety, Spike & Surge Overload Protection
• Multiple Unit Compatible Series Link Support
• Ability to Series Link Over 100+ Units
• LED Indicator Lights for Each Output on Front Panel
What’s in the Box:
• Pro Audio Power Conditioner
• Link Cable: 6.6 ft.
Technical Specs:
• Outlet Type: (8) US Standard Power Outlets
• Output Power: 2200 Watt MAX
• Rack Mount Size: 1U
• Link Connector: S-Video, 4-Pin
• Sequence Switch Time Selectable: 2 Seconds / 0.5 Seconds
• Selectable Temperature Unit Readout: Fahrenheit / Celsius
• BNC Connector: 12V/0.5 Amp
• MAX Output Current: 15 Amp RMS
• MAX Output Voltage: 275 Volt
• Power Cable Length: 5.9’ ft. (14 AWG)
• USB Power: 5V/2A (x2)
• Power Supply: 115/230V, Switchable
• Dimensions (L x W x H): 19.0’’ x 8.1’’ x 1.7’’ -inches
Stage & Studio Power Sequence Conditioner
PS1000 - PS1200
Pro Audio AV Digital Power Sequencer Controller
with Voltage & Temperature Readout, Rack Mount
