Loading ...
Loading ...
Loading ...
Operation Guide 2689
6
6. When all the settings are
the way you want, press
the A button.
• This exits the setting screen.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
❚
Stopping the Alarm Beeper
Press any button.
• In the case of the snooze alarm the alarm will sound again in
about five minutes. “SNZ” flashes while the snooze alarm is active
(indicating that the alarm will sound again).
• The snooze alarm will be canceled automatically when any of the
following occurs while the SNZ indicator is flashing on the display.
• If you turn off the snooze alarm in the Alarm Mode
• If you enter the Alarm Mode, and then display the setting
screen.
• If you enter the Timekeeping Mode and then display the setting
screen.
3. Use the D (+) and B (–)
buttons to change the
hour setting.
• Holding down either button
scrolls at high speed.
• When setting the hour, make
sure you specify AM (A) or PM
(P) correctly when using
12-hour timekeeping, or that
you specify the correct 24-
hour time.
• The same 12-hour/24-hour
format you select for the
Timekeeping Mode time is
also applied in the Alarm
Mode.
4. Press the C button so
the minute setting
flashes.
5. Use the D (+) and B
(–) buttons to change the
minute setting.
• Holding down either button
scrolls at high speed.
(Back
)
(
Forward
)
Minute
(Back)
(Forward)
❚
To set an alarm
1. In the Alarm Mode, use
the D button to scroll
through the alarm
screens until the one
whose setting you want to
configure is displayed.
Alarm 3
(AL3)
Alarm 1
(AL1)
Alarm 2
(AL2)
Alarm 4
(AL4)
Hourly Time
Signal (SIG)
Snooze Alarm
(SNZ)
2. Hold down the A button
for about two seconds
until the hour digits of the
alarm time start to flash.
• This also causes the alarm
indicator to appear and
automatically turns on the
alarm.
Alarm Number
Alarm Indicator
Hour
Alarm Mode
To turn an alarm or the hourly time
signal on or off
1.
In the Alarm Mode, use
the D button to display
the screen for the setting
you want to turn on or off.
2. Press the B button to
toggle the currently
display setting on or off.
Alarm Hourly Time Signal
Snooze Alarm
Alarm Indicator
Hourly Time Signal
Indicator
Snooze Indicator
The stopwatch measures elapsed time in units of 1/100 second up to 23 hours, 59 minutes, 59.99 seconds (24 hours). When the
maximum limit is reached, the elapsed time automatically returns to zero and timing continues from there.
Performing Stopwatch Operations
In the Stopwatch Mode, press the D button.
• Each press of the D button starts or stops the stopwatch.
• The graphic display turns on and off every five seconds,
coordinated with Timekeeping Mode time.
HoursSeconds
Minutes
1/100-second
(Start/Stop)
(Split/Reset)
Graphic Display
❚
Elapse Time Measurement
Start Stop Reset
Cumulative Time Measurement
Pressing the D button to restart the stopwatch without resetting
it to all zeros resumes elapsed time measurement from where it
was last stopped.
❚
Split Time Measurement
Record split Release split ResetStopStart
❚
1st and 2nd Place Finishers
Start 1st finisher
(Displays time
of 1st finisher.)
2nd finisher Displays time
of 2nd finisher.
Reset
Stopwatch Mode
• Pressing B while timing is being performed freezes the current elapsed time on the display, but timing of the next split continues
internally.
• Changing to another mode while a split time is displayed cancels the split time operation.
• Pressing the B button while timing is stopped resets the stopwatch to all zeros.
Your watch comes with five alarms and an hourly time signal.
❚
Daily Alarms (AL 1 to AL 4)
The watch beeps for about 10 seconds when an alarm time is
reached.
❚
Snooze Alarm (SNZ)
With the snooze alarm, the watch beeps for 10 seconds when the
alarm time is reached, and up to seven times at five-minute
intervals thereafter (approximately 30 minutes total). Pressing any
button stops the beeper, but the alarm will sound again after five
minutes.
❚
Hourly Time Signal
The hourly time signal causes the watch to beep every hour on the
hour.
❚
Testing the Alarm
In the Alarm Mode, hold down the B button to sound the alarm.
Loading ...