Loading ...
Loading ...
Loading ...
English
6
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and keep hands away from
the switch before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can causeinjury.
Charging Procedure (Fig.B)
WARNING: Do not use tool while it is connected to
the charger. The integral battery needs to be charged
before first use and whenever it fails to produce
sufficient power on jobs that were easily done before.
The battery may become warm while charging; this is
normal and does not indicate aproblem.
WARNING! Do not charge the battery at ambient
temperatures below 40°F (4 °C) or above 104°F (40 °C)
. Recommended charging temperature: approx. 104°F
(40 °C).
nOTE: The charger will not charge a battery if the cell
temperature is below approximately 40°F (4 °C) or above
104°F (40 °C).
1. Insert the charging connector
5
into the charging
port
6
.
2. Plug in thecharger.
3. Leave the tool connected to the charger for around
4hours.
4. The charging indicator will illuminate duringcharging.
Electronic Protection System
Li‑Ion tools are designed with an Electronic Protection
System that will protect the battery against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery will need to berecharged.
Important Charging Notes
1. The tool may become warm to the touch while charging.
This is a normal condition, and does not indicate a
problem. To facilitate the cooling of the tool after use,
avoid placing the tool in a warm environment such as in
a metal shed or an uninsulatedtrailer.
2. If the tool does not charge properly, take the tool and
charger to your local servicecenter.
3. You may charge a partially used battery whenever you
desire with no adverse effect on thetool.
• DO NOT use a charger with a damaged cord orplugs.
Have them replacedimmediately.
• Foreign materials of a conductive nature, such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil or any buildup of metallic particles
should be kept away from the charger and charging
contacts.
• Always unplug the charger from the power supply
when there is no tool attached toit.
Important Safety Instructions for All
Integral Battery Charging
WARNING: Read all safety warnings, instructions,
and cautionary markings for the battery, charger
and product. Failure to follow the warnings and
instructions may result in electric shock, fire and/
or seriousinjury.
• The provided charger is not intended for any uses
other than charging BLACK+DECKER rechargeable
tools. Charging other types of tools may cause
their batteries to overheat and burst, resulting in
personal injury, property damage, fire, electric shock
orelectrocution.
• DO NOT expose charger to water, rain orsnow.
• Pull by the plugs rather than the cord when
disconnecting the charger. This will reduce the risk of
damage to the plugs andcord.
• Make sure that the cord is located so that it will not
be stepped on, tripped over or otherwise subjected to
damage orstress.
• When charging the tool outdoors, always provide a
drylocation.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persist, seek medicalattention.
• Battery liquid may be flammable if exposed to spark
orflame.
• Never attempt to open the tool for any reason. If the
tool case is cracked or damaged, do not charge. Do
not crush, drop or damage the tool. Do not use a tool or
charger that has received a sharp blow, been dropped, run
over or damaged in any way (e.g., pierced with a nail, hit
with a hammer, stepped on). Damaged tools should be
returned to the service center forrecycling.
Storage Recommendations
The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold. Store the fully
charged tool disconnected from thecharger.
Transportation
nOTE: Integral Li‑ion tools should not be put in checked
baggage on airplanes and must be properly protected from
short circuits if they are in carry‑onbaggage.
Tool Disposal
This product uses a lithium‑ion rechargeable and recyclable
battery. When the battery no longer holds a charge, the tool
should be recycled. The tool should not be incinerated or
placed in thetrash.
The tool can be taken for disposal to an Authorized Service
Center. Some local retailers are also participating in a national
recycling program (refer to RBRC®). Call your local retailer for
details. If you bring the tool to an Authorized Service Center,
the Center will arrange to recycle the tool and its battery.
Or, contact your local municipality for proper disposal
instructions in your city/town.
Loading ...
Loading ...
Loading ...