User Manual Siglent SDS2000X Hd Digital Storage Oscilloscope

Documents for Siglent SDS2000X

The following documents are available:
User Manual

User Manual - (English) Read Online | Download pdf

Photos

Photos: View Photos

User Manual

For SDS2000X.

User Manual

SDS2000X Series Digital Oscilloscope

UM0102X-E02B

2018 SIGLENT TECHNOLOGIES CO., LTD.

Loading ...

Summary of Contents for Siglent SDS2000X:

Copyright and Declaration3
Safety Information4
- General Safety Summary4
- Safety Terms and Symbols6
- Measurement Category7
- Working Environment8
- Ventilation Requirement9
- General Care and Cleaning10
Exigence de Sécurité11
- Termes et symboles de sécurité14
- Définition des catégories de mesure15
- Conditions d’utilisation16
- Condition de ventilation17
- Entretien et nettoyage18
Document Overview19
Quick Start31
- General Inspection32
- Appearance and Dimensions33
- To Prepare the Oscilloscope for Use34
- The Front Panel40
- The Rear Panel41
- Front Panel Function Overview42
- User Interface50
- To Use the Security Lock52
To Set the Vertical System53
- To Enable the Channel54
- To Adjust the Vertical Scale55
- To Adjust the Vertical Position55
- To Specify Channel Coupling56
- To Specify Bandwidth Limit56
- To Specify Probe Attenuation Factor57
- To Specify channel Input Impedance57
- To Specify Amplitude Unit58
- To Invert a Waveform58
Set the Horizontal System59
- Adjust the Horizontal Scale60
- Adjust Trigger Delay61
- Set the Roll mode62
- Use the Zoom Function63
To Set the Sample System64
- Run Control65
- Overview of Sampling66
- To Specify Memory Depth69
- To Select Sampling Mode69
- To Select Waveform Interpolation Method70
- To Select Acquisition Mode72
- To Change the Horizontal Format76
- Use Sequence Mode77
To Trigger the Oscilloscope79
- Trigger Source81
- Trigger Mode82
- Trigger Level83
- Trigger Coupling84
- Trigger Holdoff85
- Noise Rejection86
- Trigger Type88
Serial trigger and decode108
- IIC Trigger and Serial Decode109
- SPI Triggering and Serial Decode117
- UART/RS232 Trigger and Serial Decode124
- CAN Trigger and Serial Decode130
- LIN Triggering and Serial Decode136
Digital Channels141
- To Connect the Digital Probes to the Device-under-test142
- Acquiring Waveform Using the Digital Channels143
- To Change the Display Type of the Digital Channels143
- To Switch a Single Channel On or Off145
- To Switch All Digital Channels On or Off145
- To Change the Logic Threshold for Digital Channels145
- To Reposition a Digital Channel146
- To Display Digital Channels as a Bus146
To Save Reference Waveform148
- To Save REF Waveform to Internal Memory149
- To Display REF Waveform149
- To Adjust REF Waveform Display150
- To Clear REF Waveform Display150
To Use the Math Operation151
- Units for Math Waveforms152
- Math Operators153
- To Adjust the Math Waveform Scale and Offset162
  - To Adjust the Math Waveform Horizontal Scale and Offset162
  - To Adjust the Math Waveform Vertical Scale and Offset162
To Make Cursor Measurements163
- X Cursors163
- Y Cursors163
- To Make Cursor Measurements164
To Make Measurements165
- Type of Measurement166
- To Make Automatic Measurements170
- To Clear Measurement Parameters172
- To Make All Measurement172
Display Setting173
- To Set Display Type174
- To Set Color Display175
- To Set and Clear Persistence175
- To Clear the Display176
- To Select Grid Type177
- To Adjust Waveform Intensity177
- To Adjust Grid Brightness179
- To Adjust Transparence179
Save and Recall180
- Save Type181
- Internal Save and Recall182
- External save and recall183
- Disk Management186
System Function Setting189
- To View the System Status190
- To Do Self-Calibration191
- To Enable or Disable the Sound192
- To Specify the Language192
- To Enable Pass/Fail Test193
  - To Set and Perform Pass/Fail Test194
  - To Save and Recall Test Mask195
- I/O Set197
- To Do Power Analysis200
  - To Perform Channel Deskew201
  - Perform Power Analysis203
- To Enable Quick-Cal227
- To Update Firmware and Configuration228
- To Perform a Self-Test229
- To Specify the Screen Saver Time232
- Option Management233
To Use the History Function235
Arbitrary Waveform Generator237
- To Set Wave Type and Parameters238
- To Output Arbitrary Waveform240
- To Set Output Load241
- Recover the Default Setup of AWG.241
- To Do AWG Self-Cal242
Default Setup243
Troubleshooting249

File type: PDF

File name: 2050415_sds2000x.pdf

File size: 3.65 MB

File Language: English

Pages: 250

Author: Siglent

File created: 2023-04-07

Published: 2023-04-09

Updated: 2023-04-08

Download File

Specifications

Brand: Siglent

Model: SDS2000X

Category: Tools - Home Improvement

See other models: SHS806 SPD3303X-E SDG2042X SDS1052DL+ SDS1102CML+

Photos

Download User Manual