Loading ...
Loading ...
Loading ...
raCEAND WATERDmSPENSERFEATURES
Theiceandwaterdispenserconvenientlydispenseschilledwater,andicecubesorcrushedice,dependingonthemodel.
Tooperatetheicedispenser,selecttheiceoptiondesiredusingthetouchpad.Pressaglassagainstthedispensingpaddle
asfarupaspossibletocatchallice.Tostopdispensingice,pullglassawayfromdispensingpaddle.Donotremovethe
glassuntiltheicehascompletelydispensed.(Completeinstructionsforthedispenseroperationareattachedtotheinside
ofthefreezerdoor.)
How the Water Dispenser Works
The water tank located behind the refrigerator compartment, automatically fills aswater is dispensed. For proper dispenser
operation, the recommended supply water pressure should fall between 20 psi and 100 psi.
After the refrigerator is connected to the water supply, fill the water tank by drawing one glass of water, it may take about
1_/_minutes after activating the dispenser paddle before water begins to fill this first glass. Continue flushing the system
for 3 minutes to rid the tank and plumbing connections of any impurities. The water dispenser has a built in shutoff device
that will stop the water flow after 3 minutes of continuous use. Simply release the dispenser paddle to reset the shutoff
mechanism.
ChemioaJsfromomaJfunCti0nlngsoftenerCandamagetheioemaker.Iftheicemakeriso0nneoted
to soft water, ensure that the softener is maintained and working properJy.
How the Ice Dispenser Works
The ice maker and container are located in the top of the freezer compartment. After the
refrigerator is installed properly and has cooled for several hours, the ice maker can begin
making icewithin 24 hours. Air in new plumbing lines may cause the ice maker to cycle two
or three times before making a full tray of ice. Ice production is controlled by the ice
maker's On/Off power switch. Press the switch to the "O" position to turn it Off and press it
to the '1" position to turn it On. With no usage it will take approximately 2 days to fill the ice
container. The ice maker also has a built-in wire signal arm,which automatically stops ice
production when the ice bin is full. This signal arm should not be used to manually stop the
ice maker.
Because of new plumbing connections, the first production of ice cubes may be discolored
or have an odd flavor. These should be discarded until the cubes made are free of discoloration and taste.
raCE DISPENSER TraPS
• Ice cubes stored too long may develop an odd flavor. Empty the ice container and ensure that the ice maker's On/Off
power switch is turned On (set to the '1" position). The ice maker will then produce more ice.
• Occasionally shake the ice container to keep ice separated.
• Keep the icemaker's On/Off power switch turned Off (set to the "O" position)until the refrigerator isconnected to the water
supply or whenever the water supply isturned off.
IMPORTANT: The ice maker is turned On at the factory S0 it can work as soon as you !nstall your refrigerator_ !f you
cannot connect a water supply, turn the On!Off switch to the Off ("O') position; Otherwise, the ice maker's valve
may be n0isy When it attempts to operate without Water.
If the dispensing paddle is pushed for more than 4 minutes, the dispenser motor may overload
_ and stopl The overload protector will reset automatically after 3 Or 4 minutes.
• If a large quantity of ice is needed at one time, it is best to remove cubes directly from the ice container.
• The following sounds are normal when the ice maker is operating:
• Motor running • Ice loosening from tray
• Ice dropping into ice container • Running water
• Water valve opening or closing
, Turn Off the ice maker when cleaning the freezer and during vacations.
• If the ice maker will be turned off for a long period of time, you should also turn off the water supply valve.
14
Loading ...
Loading ...
Loading ...