Loading ...
Loading ...
Loading ...
10
away from children. If you think batteries might
have been swallowed or placed inside any part of
the body, seek immediate medical attention.
CAUTION: Risk of explosion if the battery is
replaced by an incorrect type. Dispose of used
batteries according to the instructions. Improper
replacement of the battery with an incorrect type
may defeat a safeguard (for example, in the case
of some lithium battery types). Do not dispose of
the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may
result in an explosion. Do not leave the battery in
an extremely high temperature surrounding
environment, which may result in an explosion or
the leakage of flammable liquid or gas. Do not
subject the battery to extremely low air pressure,
which may result in an explosion or the leakage of
flammable liquid or gas. + identifies the positive
terminal(s) of equipment which is used with, or
generates direct current. - identifies the negative
terminal(s) of equipment which is used with, or
generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles,
should be placed on the equipment. The serial
port of the equipment is used for debugging only.
Hot Surface Prevention
CAUTION: Hot parts! Burned
fingers when handling the
parts. Wait one-half hour after
switching off before handling
parts. This sticker is to indicate that the marked
item can be hot and should not be touched
without taking care. For device with this sticker,
this device is intended for installation in a
restricted access location, access can only be
gained by service persons or by users who have
been instructed about the reasons for the
restrictions applied to the location and about any
precautions that shall be taken.
Installation
Install the equipment according to the
instructions in this manual.
Power Supply
Device powered by Safety Extra-Low
Voltage(SELV): The power source should meet
limited power source or PS2 requirements
according to IEC 60950-1 or IEC 62368-1 standard.
Device powered by AC mains supply voltage: The
equipment must be connected to an earthed
mains socket-outlet. An appropriate readily
accessible disconnect device shall be incorporated
external to the equipment. An appropriate
overcurrent protective device shall be
incorporated external to the equipment, not
exceeding the specification of the building. An
all-pole mains switch shall be incorporated in the
electrical installation of the building. Ensure
correct wiring of the terminals for connection to
an AC mains supply. The equipment has been
designed, when required, modified for connection
to an IT power distribution system.
White Light Illuminator (If supported)
Possibly hazardous optical radiation emitted from
this product. DO NOT stare at operating light
source. May be harmful to the eyes. Wear
appropriate eye protection or DO NOT turn on the
white light when you assemble, install or maintain
the camera.
Transportation
Keep the device in original or similar packaging
while transporting it.
System Security
The installer and user are responsible for
password and security configuration.
Maintenance
If the product does not work properly, please
contact your dealer or the nearest service center.
We shall not assume any responsibility for
problems caused by unauthorized repair or
maintenance. A few device components (e.g.,
electrolytic capacitor) require regular
replacement. The average lifespan varies, so
periodic checking is recommended. Contact your
dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside
and outside surfaces of the product cover. Do not
use alkaline detergents.
Using Environment
DO NOT place the camera in extremely hot, cold,
dusty or damp locations, and do not expose it to
high electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the
power cable, and contact the service center.
Time Synchronization
Set up device time manually for the first time
access if the local time is not synchronized with
that of the network. Visit the device via Web
browse/client software and go to time settings
interface.
Reflection
Make sure that no reflective surface is too close
to the device lens. The IR light from the device
may reflect back into the lens causing reflection.
Français
Déclaration de conformité UE
Ce produit et - le cas échéant -
les accessoires fournis sont
marqués « CE » et sont donc
conformes aux normes
européennes harmonisées
applicables énumérées dans la directive CEM
2014/30/UE, la directive DBT 2014/35/UE, la
directive RoHS 2011/65/UE, dispositif Wi-Fi : la
directive RE 2014/53/UE
2012/19/UE (directive DEEE) :
Dans l’Union européenne, les
produits portant ce pictogramme
ne doivent pas être déposés
dans une décharge municipale
où le tri des déchets n’est pas
pratiqué. Pour un recyclage
adéquat, remettez ce produit à votre revendeur lors
de l’achat d’un nouvel équipement équivalent, ou
déposez-le dans un lieu de collecte prévu à cet effet.
Pour plus de précisions, rendez-vous sur :
www.recyclethis.info
Loading ...
Loading ...
Loading ...