Loading ...
Loading ...
Loading ...
7
English
Installing and Removing Attachments
(Fig.D)
WARNING: Shock hazard. Under no circumstances
should this product be used nearwater.
WARNING: Burn hazard. Moving parts within the
power unit become hot during use. Avoid contact with
moving parts within power unit when removing and
installingaccessories.
WARNING: Before assembly, lock the power unit by
setting the forward/reverse slider
3
to the center
position and remove the battery from the Power Unit.
Remove any accessory from the attachment before
removing or installing theattachment.
WARNING: To reduce the risk of injury, do not place
fingers or other objects inside the power unit, other
than the attachments designed to work with the
powerunit.
• Lock the power unit by setting the forward/reverse
slider
3
to the centerposition.
• To remove an attachment, depress the release button
4
and take the attachment off thetool.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulatedtrailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local servicecenter.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the batterypack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaningsolutions.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
• Do not operate the charger with a damaged cord
orplug–have them replacedimmediately.
• Do not operate the charger if it has received a sharp
blow, been dropped or otherwise damaged in any
way. Take it to an authorized servicecenter.
• Do not disassemble the charger; take it to an
authorized service center when service or repair
is required. Incorrect reassembly may result in a risk of
electric shock, electrocution orfire.
• The charger is designed to operate on standard
120V household electrical power. Do not attempt to
use it on any other voltage. This does not apply to the
vehicularcharger.
• Foreign materials of a conductive nature, such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil or any buildup of metallic particles
should be kept away from the chargercavities.
• Always unplug the charger from the power supply
when there is no battery pack in thecavity.
Charging a Battery (Fig. C)
1. Plug the charger into an appropriate outlet.
2. Insert and fully seat battery pack. Green charging light
will continuously blink whilecharging.
3. Charging is complete when the green light remains
continuously ON. Battery pack can be left in charger
orremoved.
WARNING: Only charge batteries in air temperature
over 40° F (4.5° C) and below 105° F (+40.5° C).
4. Charger will not charge a faulty battery pack, which may
be indicated by the light staying OFF or the red light
rapidly blinking. Take charger and battery pack to an
authorized service center if light staysOFF or red light
rapidlyblinks.
nOTE: Refer to label near charging light on charger for
blinkpatterns.
hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery packlife.
A cold battery pack may charge at a slower rate than a warm
batterypack.
The hot/cold pack delay will be indicated by the red light
continuously flashing a short ON followed by a longer ON
(see charger for blink pattern). Once the battery pack has
reached an appropriate temperature, the charger will resume
the chargingprocedure.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to berecharged.
Loading ...
Loading ...
Loading ...