OWNER’S MANUAL
IN230500099V01_US
820-359V80
INFRARED ZONE
HEATING SYSTEM
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
2
Thank you for choosing a the Infrared Zone Heating System. This owner’s manual will
provide you with valuable information necessary for the proper care and maintenance of
your new product. Please take a few moments to thoroughly read the instructions and
familiarize yourself with all the operational aspects of your new heater.
IMPORTANT INSTRUCTIONS
When using this electric unit, basic safety precautions should always be followed to
reduce the risk of fire, electric shock, and injury to persons, and hyperthermia, including
the following:
1. Read ALL instructions before using this unit.
2. CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater by
yourself.
3. This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot
surfaces. If provided, use handles when moving this heater.
4. Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and
curtains at least 3 ft from the front of the heater and keep them away from the sides,
top, and rear. DO NOT place towels or other objects on the heater.
5. Extreme caution is necessary when any heater is used by or near children or the
disabled, or when the heater is left operating and unattended.
6. DO NOT operate any heater with a damaged cord or after the heater malfunctions,
has been dropped or damaged in any manner. Return heater to authorized service
facility for examination, electrical or mechanical adjustment, or repair.
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. NEVER locate heater where it may fall into a bathtub or other water
container. To protect against electrical hazards, DO NOT immerse in water or other
liquids.
8. DO NOT touch the control panel or plug with a wet hand.
9. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or
similar coverings. Arrange cord away from traffic area and where it will not be tripped
over.
10. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening
as this may cause an electric shock or fire, or damage the heater.
11. To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner.
DO NOT use on soft surfaces, like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. DO NOT use in areas where
gasoline, paint, explosive and/or flammable liquids are used or stored. Keep unit
away from heated surfaces and open flames.
13. Always plug heaters directly into a wall outlet receptacle. Never use with an
extension cord or relocatable power tap (outlet/power strip).
14. To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical outlet.
15. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull firmly
on the plug, DO NOT unplug by pulling on the cord.
16. Always unplug the unit before moving or cleaning, or whenever the heater is not in
use.
17. Use only for intended household use as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to
persons. The use of attachments not recommended or sold by unauthorized dealers
may cause hazards.
3
18. Always use on a dry, level surface. Use on floor only.
19. DO NOT use outdoors.
20. WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any
solid-state speed control device.
21. DO NOT attempt to repair or adjust any electrical or mechanical functions on this
unit. Doing so will void your warranty. The inside of the unit contains no user
serviceable parts. Qualified personnel should perform all servicing only.
22. Hyperthermia can result in death. Symptoms of hyperthermia include high body
temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid
pulse. If you begin to experience symptoms related to hyperthermia, turn off the
heater and seek medical attention.
23. To avoid excessive room temperatures which can cause hyperthermia: DO NOT
leave product running unattended in a confined space around infants, or individuals
with reduced physical, sensory, or mental capabilities.
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
Voltage Rating
Power Consumption
Unit Size
Unit Weight
120V (60Hz)
1500W
7.09 in. (W) x 10.04 in. (D) x 13.19 in. (H)
5.78 lbs
SAFETY FEATURES
Tip-Over Safety Feature
This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an
internal switch will automatically shut the heater off. Once the heater is restored an
upright position, the heater will reset. To continue operation, turn on the heater using the
supplied remote control or the control panel on the heater.
Overheat Safety Feature
This heater is equipped with a overheat safety feature. When the heaters internal
components reach a certain temperature that could cause overheat and possible fire,
the heater will automatically shut off.
WARNING: It is normal for the power cord to feel warm to the touch; however, a loose fit
between the outlet and the plug may cause overheating of the plug. If this occurs, try
inserting the plug into a different outlet. Contact a qualified electrician to inspect the
original outlet for damage.
4
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is
wider than the other). To reduce the risk of electric shock, this
plug is intended to fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
IN THE BOX
* INFRARED ZONE HEATING SYSTEM
* REMOTE CONTROL(batteries not Included)
* INSTRUCTION BOOKLET
PRODUCT DIAGRAM
Air Outlet
Control panel
Remote Control
Air Intake
Footpads
5
Control panel
1. Temp up button: To increase desired temperature.
2. ON/OFF button: Powers the display on and off.
3. Temp down button: To decrease desired temperature.
4. Mode button: To select between High、Low and Eco modes.
5. Digital display: Indicate set room temperature or time or heating mode or lock.
6. Signal receiving window: For receiving remote control signal.
7. Timer button: Used to engage timer mode and to set hour value for the timer.
Remote Control
ON/OFF button: Used for power-on or power-off.
Mode button: Used for mode selection.
Temp up button: to make set temperature rise.
Temp down button: to make set temperature decline.
Timer button: Used for setting timer and adjust time value of
timing.
6
PREPARATION
Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power
outlet. and turn on the power switch in the rear of the unit. Only operate heater in upright
position.
Insert 1 CR2025 batteries into the remote control before using (Batteries Not Included)
Remote control
Battery cover
Battery
OPERATING INSTRUCTIONS
1. Start and select working mode
Turn the heater on by pressing the ON/OFF button on
the control panel or by pressing the Power button on
the supplied remote control.
Once power is off, heating element will stop working at
first. Fan will prolong working for 3 min to emit plenty of
heat inside. This mark will indicate running during the 3
min.
Select a heat Mode
Press the MODE button to toggle between the three
heat modes.
High Mode uses 1500W; Low Mode uses 1000W. ECO
mode is an Economic Energy Saving Function. When
ECO mode is chosen, the heater will manage itself from
less to more heating power (watts) in an attempt to
maintain a constant warm 68℉.
7
2. Setting Desired Temperature
Adjust the desired temperature by pressing the
Up/Down arrows on the control panel or remote control.
Desired temperature options vary from 59℉ to 86℉.
Once you have chosen the desired temperature, the
heater will remain on until the room temperature
increases to the temperature on the digital display. The
heater will cycle on and off to maintain the desired room
temperature.
3. Setting the POWER OFF TIMER Function
Note: The Power-Off-Timer Function will allow for the heater to power OFF after a
certain set time, and can only be set while the heater’s display is in the “On” position.
Turn the heater to the “On” position .Press the Timer
button on the heater’s control panel or the remote.
The digital display changes from the “temperature” to
the “hours” option for the timer. Continue to press the
timer button to change the number of hours you would
like the heater to run before powering itself off .The
hour options for the timer are from 0 to 12 hrs. (in 1 hr
increments).
The selected hour increments will flash for a few
seconds, then revert back to the set desired
temperature. The heater will power OFF when the
internal heater clock counts down the hour increments
you set.
4. Setting the POWER-ON-TIMER Function
Note: The Power-ON-Timer Function will allow for the heater to power ON after a
certain set time, and can only be set while the heater’s display is in the “Off” position.
Turn the heater to the “OFF” position .Press the Timer
button on the heater’s control panel or the remote.
The digital display shows the “hours” option for the
timer. Continue to press the timer button to change the
number of hours you would like the heater’s internal
clock to count down before powering itself on .The
hour options for the timer are from 0 to 12 hrs. (in 1 hr
increments).
As long as a timer is set, the digital screen will always
display the timing time. The heater will power itself ON
when the internal heater clock counts down the hour
increments you set.
8
5. Setting electro lock
The Electro Lock can help avoid the heater from being accidentally engaged by children.
The locking mechanism can be set in both the ON and OFF modes.
Press Temp Up and Temp Down buttons at the same
time for 3 seconds. Locking is complete when you hear
a beep. When locked, the functions of the control panel
and remote will be locked for use.(LC displayed on the
digital screen)
When you need to unlock it, press Temp Up and Temp
Down buttons at the same time for 3 seconds. You will
hear a beep .The control panel and remote control will
become functional again.
MAINTENANCE
1.Turn off the heater on by pressing the ON/OFF button on the control panel or by
pressing the Power button on the supplied remote control.
2. Unplug the unit and let it cool completely.
3. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You
may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth.
CAUTION: DO NOT let liquid enter the heater.
4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes
to clean the heater. This may cause damage or deterioration to the surface of the
heater.
5. DO NOT immerse the heater in water.
6. Wait until the unit is completely dry before use.
7. If won’t use the unit for a long time, please take out battery in remote control
according to following steps, then take care of the remote control.
Remote control
Battery cover
Battery
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-
up, use the original packaging to repack the unit.
9
BASIC TROUBLESHOOTING
If the heater will not operate, please check the following before seeking repair advice:
1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the main fuse is working.
3. Check to see if the battery on the remote is placed correctly, undamaged.
NOTE: For the heater to function properly, the desired temperature on the heater must
be set a few degrees higher than the temperature in the room. If the seems to not be
heating, increase the desired temperature on the heater to engage the heat elements.
If you have any questions, please contact our customer care center.
Our contact details are below:
001-877-644-9366
customerservice@aosom.com
Imported by Aosom LLC
27150 SW Kinsman Rd Wilsonville, OR 97070 USA
MADE IN CHINA
10
