Loading ...
Loading ...
Loading ...
NEW 11/18 2 T48312_T48314ES
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
CAUTION
• AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these de-
vices may overheat and cause a fire hazard.
• DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a
fire hazard.
• ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
• NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
• DO NOT block, cover or obstruct air flow to or from the Fan while in operation.
• DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may
create a shock hazard.
• DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will not be tripped over.
• NEVER use a single extension cord to operate more than one Fan or other electrical device.
• DO NOT use this Fan if it has been damaged or is not functioning properly.
• Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,
move the Fan to another location.
• Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
• THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008). This Fan is not suitable for use in agricultural
facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article
547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
• THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008). This Fan is not suitable for use in hazardous lo-
cations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user is cautioned that changes
and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT use this Fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!
ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet and
create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition should
be replaced by a qualified electrician.
ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means
of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the
Fan when not in use.
BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The Blue Plug
™
on your Lasko Fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed
or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace, repair or tamper
with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.
THIS FAN HAS A POLARIZED PLUG (one blade is wider than the other). This plug is designed to fit into the outlet only one way.
Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety feature. If the
plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced.
NEW 11/18 7 T48312_T48314ES
MODELO T48312/T48314
CONTROL REMOTO
1. Instale las dos baterías “AAA” (no incluídas), como se muestra
en la Figura 5.
2. Todas las funciones realizadas con el Control Remoto pueden
realizarse de igual forma con los Controles Manuales.
3. No mezcle baterías viejas y nuevas. No mezcle baterías alca-
linas, estándar (carbono-cinc) o recargables (níquel-cadmio).
4. NO ARROJE LAS BATERÍAS AL FUEGO, LAS BATERÍAS PUEDEN
ESTALLAR O PUEDE DERRAMARSE EL LÍQUIDO CONTENIDO.
Figura 1
#8 x 3/8"
Tornillos
Base de Soporte B
Base de
Soporte A
Copas
Figura 2
Conjunto de la
Base de Soporte
Cable Eléctrico
M5 X 1/2" Tornillos
Conjunto de la
Base de Soporte
Cable Eléctrico
Canal Conductor
de Cable
Figura 3
ENSAMBLAJE
1. Para facilitar el armado, recueste el Ventilador de modo que la parrilla
negra y el tablero de control den hacia arriba.
2. Arme las Mitades de la Base de Apoyo encastrando las Puntas de la
Base de Apoyo A con los Orificios para Puntas en la Base de Apoyo B.
Asegure (2) #8 X 3/8" Tornillos en los dos orificios externos en la parte
inferior de la Base. (Figura 1)
3. Conecte el Cable Eléctrico a través del orificio grande en el centro de
la Montura de la Base de Apoyo. (Figura 2)
4. Alinee la Montura de la Base de Apoyo con la Base del Motor, teniendo
en cuenta que la ranura del cable en la parte inferior de la montura de
la base de apoyo debe apuntar hacia la parte posterior del Ventilador.
Adose la Montura de la Base de Apoyo a la Base del Motor con Tornillos
Largos M5 de 1/2". Cerciórese de alinear la Llave del Conjunto de la
Base de Soporte con la Muesca Localizadora de la Base Del Motor.
(Figura 1) Suavemente tire del Cable Eléctrico para evitar que quede
flojo y colóquelo en el Orificio de Colocación del Cable. (Figura 3)
OPERACIÓN
Puede operar este ventilador con los controles manuales ubicados en la
parte superior de la unidad (Figuras 5) o con el control remoto (Figuras 6).
1. Coloque el ventilador sobre una superficie firme y nivelada.
2. Conecte el cable eléctrico a un tomacorriente de 120 volts.
Asegúrese que el enchufe encaje
firmemente en el tomacorriente.
De no encajar firmemente en el tomacorriente, podrían de-
slizarse parcial o completamente fuera del tomacorriente
apenas con un ligero movimiento del cable conectado. Los
receptáculos en esta condición pueden sobrecalentarse y
constituir un grave riesgo de incendio; si está cubierto por
una cortina, el peligro de incendio es aún mayor.
3. Suministre corriente eléctrica al ventilador al presionar el Botón de Encen-
dido ( ). El ventilador operará inicialmente en velocidad alta, velocidad 3.
4. VELOCIDAD DEL VENTILADOR: Ahora usted puede ajustar la veloci-
dad del ventilador al nivel deseado, 3, 2, o 1 oprimiendo el Botón de
Velocidad ( ).
5. OSCILACIÓN: Presione el Botón de Oscilación ( ) para iniciar y detener
la función de oscilación.
6. FUNCIÓN DE TEMPORIZADOR: Este ventilador está equipado con
un temporizador. El temporizador se puede configurar para 1-7 horas.
Continúe pulsando el Botón del Temporizador ( ) para llegar a la con-
figuración de tiempo deseada. Para cancelar el temporizador, pulse el
Botón de Temporizador ( ) hasta que las luces se apaguen.
7. CARACTERÍSTICA DE NOCHE: Presione el Botón de Noche ( ) una vez
para activar la función. Las luces del ventilador se atenuarán un 50 %. El
ventilador funcionará en la configuración alta (3) por una hora, cambiará
a la configuración media (2) por una hora y, por último, cambiará a la
configuración baja (1) hasta que el usuario interactúe con el ventilador.
La funcion de noche no funciona con ninguna otra funcion, exepto osci-
lacion. Presione Cualquier otro boton para cancelar la funcion de noche.
8. Después de apagar el ventilador, desconecte la unidad del tomacor-
riente eléctrico.
Figura 4
Botón de Velocidad
Botón Temporizador
Botón de Noche
Botón de Oscilación
Botón de
Encendido/Apagado
TIMER
POWER
OSC
SPEED
LOUVERS
TIMER
POWER
OSC
SPEED
NIGHT
Figura 5
Botón de
Encendido
Apagado
Botón de
Velocidad
Baterías
AAA
Oscilación Botón
Botón de
emporizador
Botón de Noche
Loading ...