Loading ...
Loading ...
Loading ...
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
■ Drill
■ 1¹⁄₄" (3.2 cm) drill bit
■ ¹⁄₈" (3.2 mm) drill bit for pilot holes
■ Pencil
■ Wire stripper or utility knife
■ Tape measure or ruler
■ Caulking gun and weatherproof caulking compound
■ Flat-blade screwdriver
■ Phillips screwdriver
■ Saber or keyhole saw
■ Vent clamps
■ Metal snips
■ Compass or circle template
Parts supplied
Remove parts from package. Check that all parts are included.
■ 2 - Metal filters
■ 4 - 4.5 x 13 mm mounting screws
■ 2 - 3.5 x 9.5 mm damper screws
■ 6" (15.2 cm) transition with damper
■ 4 - 5 x 45 mm screws
■ 4 - 10 x 60 mm wall anchors (for wall mounting)
■ 4 - 5.4 x 75 mm screws (for 10 x 60 mm wall anchors)
■ T10 Torx
®†
adapter
■ T20
®
Torx
®
adapter
Parts needed
■ Home power supply cable
■ ½" (12.7 mm) UL listed or CSA approved strain relief
■ 3 - UL listed wire connectors
For top vented installations:
■ 6" (15.2 cm) round metal venting
■ 1 - wall or roof cap
For non-vented (recirculating) installations:
■ Recirculating Kit W10490330 - See “Assistance or Service”
section to order.
■ 6" (15.2 cm) round metal venting
For rear vented installations:
■ 3¹⁄₄" x 10" (8.3 x 25.4 cm) rectangular metal venting
■ 1 - wall or roof cap
■ 3¹⁄₄" x 10" (8.3 x 25.4 cm) Damper Assembly/Motor Mounting
Bracket Kit (see “Accessories” in the “Assistance or Service”
section to order)
For cabinets with recessed bottoms:
■ 2 - 2" (5.1 cm) wide filler strips. Length and thickness
determined by recess dimensions.
■ 4 - flat-head wood screws or machine screws with washers
and nuts (to attach filler strips).
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■ It is the installer’s responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located inside the range hood
on the left wall.
■ Range hood location should be away from strong draft
areas, such as windows, doors and strong heating vents.
■ Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance. Consult the
cooktop/range manufacturer installation instructions before
making any cutouts.
■ This range hood is recommended for use with cooktop
with a maximum total rating of 65,000 BTUs or less.
■ Grounded electrical outlet is required. See “Electrical
Requirements” section.
■ The range hood is factory-set for vented installations. For
non-vented (recirculating) installations, the Recirculation Kit
is W10490330. Replacement Charcoal Filters Part Number
is W10272068. See the “Assistance or Service” section to
order.
■ All openings in ceiling and wall where range hood will
be installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
†®TORX and T20 are registered trademarks of Acument Intellectual Properties,
2"
(5.1 cm)
9"
(22.9 cm)
12"
(30.5 cm)
7¼"
(18.4 cm)
1³⁄₁₆"
(3.0 cm)
1¹⁄₁₆"
(2.6 cm)
13¹²⁄₁₆"
(35 cm)
29⁷⁄₈" (75.9 cm) - 30" (76.2 cm) model
35⁷⁄₈ (91.1 cm) - 36" (91.4 cm) model
19³⁄₄"
(50.2 cm)
3" (7.6 cm) -
30" (76.2 cm) model
5³⁄₄" (14.6 cm) -
36" (91.4 cm) model
⁵⁄₈"
(1.6 cm)
Loading ...
Loading ...
Loading ...