Loading ...
Loading ...
Loading ...
Operation Guide 5535
E-66
Power Supply: One lithium battery (Type: CR2016)
Approximate battery operating time: 3 years under the following conditions:
x 1 illumination operation (1.5 seconds) per day
x Alarm: 10 seconds/day
Frequent use of illumination runs down the battery.
Specifications are subject to change without notice.
E-65
Countdown Timer:
Measuring unit: 1 second
Countdown range: 100 minutes
Countdown start time setting range: 1 second to 100 minutes
(1-second increments)
Timer alert time: 10 seconds
Alarms: 5 daily alarms; Hourly time signal
Dual Time: Hour, minutes
Setting Unit: 15 minutes
Other: Daylight Saving Time (summer time)/Standard Time
Illumination: LED (light-emitting diode); Selectable illumination duration
(approximately 1.5 seconds or 3 seconds); Auto light
Other: Alarm test; Button operation tone on/off; Moving the Hands to View the
Digital Display
E-64
Specifications
Accuracy at normal temperature: ±15 seconds a month
Digital Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the
week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Standard Time/Daylight Saving Time (summer time)
Analog Timekeeping: Hour, minutes (hand moves every 10seconds), seconds
Stopwatch/Data Recall:
Measuring unit: 1/100 second (1 second after 1 hour)
Measuring capacity: 23 hours 59 minutes, 59 seconds (24 hours)
Measuring modes: Elapsed time, Lap time, Lap memory (120 records)
One-press timing start from the Timekeeping Mode
E-63
Main Indicators
Number Name See
1
1
PM indicator E-16
2
2
Hands shifted indicator E-14
3
3
LAP indicator E-36
4
4
DST indicator E-21
5
5
Auto light switch on indicator E-55
6
6
Alarm indicator E-47
7
7
Hourly time signal indicator E-47
75 6
1 2 3 4
E-62
Troubleshooting
Time Setting
■ The current time setting is off by one hour.
You may need to change standard time/daylight saving time (DST) setting. Use the
procedure under “Adjusting the Digital Time and Date Settings” (page E-17) to change
the standard time/daylight saving time (DST) setting.
E-61
Button Operation Tone
You can turn the button operation tone on or off as
desired.
x Even if you turn off the button operation tone, alarms,
the Hourly Time Signal, and other beepers all operate
normally.
To turn the button operation tone on or off
1. In the Timekeeping Mode, hold down A until the
seconds digits start to flash (about two seconds).
x This enables setting of the seconds.
2. Press C eight times to display the button operation tone On/Off screen (page E-18).
The screen will show either BEEP ON or BEEP OFF.
3. Press D to toggle the setting between BEEP ON and BEEP OFF.
4. After all the settings are the way you want, press A to exit the setting screen.
E-60
3. Press C.
x This enters the hour and minute hand adjustment
mode.
x Press C again* to return to the second hand
adjustment mode.
* Nothing will happen if you press C while the hands
are moving.
x 0:00 flashes on the display while the hour and minute
hands are moving to the home position (12 o’clock).
4. If the hour and minute hands are not at 12 o’clock,
use D and B to adjust them until they are.
5. Press A to return to the Timekeeping Mode.
Check to make sure that the time indicated by the
hands matches the time on the digital display. If the
times don’t match, perform the correction procedure
above again.
Hour hand and minute hand