PACA100ECO User Manual

Loading ...

PREPARING FOR OPERATION IN WA-

TER MODE

Oncetheappliancehasbeeninstalled,itisready

foruse.

However,itsefciencycanbeenhancedbyope-

ratingitintheexclusiveDe’longhiwatermode.

Thewaterinthetankincreasesthecoolingpo-

werofyourPinguinoandatthesametimeredu-

cesnoiselevelsandelectricalconsumption.

Comparedtoair,waterreducesthetemperature

ofthecoolingcircuitmuchmoreefciently,be-

forebeinggivenofffromtheairexhausthosein

theformofvapour.

Rememberthat:

• Youmust alwaysuse salt-freeclean mains

water.

• Thelengthoftimethewaterinthetanklasts

depends greatly on environmental condi-

tionssuchastemperature,humidity,insula-

tion,theexposureoftheroom,thenumber

ofpeoplepresent,etc.

 Indicativelyitlastsaboutsixhours.

 TheBOOSTfunction(seepage30)shortens

theoperatingtimetoabout4hours,butthe

coolingpowerandefciencyareincreased.

• When the water in the tank runs out, the

light comesonandoperationofthe

applianceswitchesautomaticallytoair-air.At

thesametime,thequantityofairgivenout

fromtherearhoseincreases.

The appliance is ﬁtted with a resin lime-

scale ﬁlter enabling normal tap water to be

used.

The impregnated resins reduce water hardness

and therefore prolong the working life of the

appliance.

“CF” is displayed when the limescale ﬁl-

ter needs replacing. The efﬁcacy of the ﬁlter

depends on water hardness. It should, howe-

ver, be replaced every ﬁve years.

Setting water hardness

Measurewaterhardnessusingtheindicatorpa-

perprovided.

• Remove the indicator paper from its pack

(V).

• Immersethepapercompletelyinaglassof

waterforonesecond.

• Removethepaperfromthewaterandsha-

ke lightly. After about a minute, 1, 2, 3, 4

or 5 redsquaresappear, depending onthe

hardnessofthewater.Theappliancecanbe

set to three different waterhardness levels

soft(H1),medium(H2)andhard(H3).De-

terminethehardnessofthewateryouwillbe

usingbycomparingtheredsquaresonthe

indicatorpaperwiththetablebelow.

 Tosetwaterhardness,proceedasfollows:

1. Settheappliancetostand-by.

2. Hold the FAN button on the control panel

downfor10seconds.Theapplianceemitsa

beepand

H1, H2 orH3isdisplayed.

3. Use the+or - buttonstoset the hardness

levelaccordingtothetablebelow.Waitafew

seconds for the setting to be memorised.

Theapplianceemitsanotherbeepandgoes

backtostand-by.

The machine is set by default for medium

hardness (H2).



Filling the tank

The watertank is located at thebottom of the

appliance.Removethetankbyinsertingthehand

through the door above the word “PULL” (g.

13)andpullingthetankoutasfarasitwillgo.

Removethecapanduseacontainer(bottle,jug,

wateringcan)topourinthewater(g.14/15).

Youcanseewhenthetankisfullthroughthel-

soft

Kind of water used Levels

Medium

Hard

Loading ...

User Manual - Page 6