ENGLISH_index
Stand
www.lg.com
Printed in Korea
Copyright © 2022 LG Electronics Inc.
All Rights Reserved.
OWNER’S MANUAL
Please read this manual carefully before
operating your set and retain it for future
reference.
SQ-G2DT97
The model and serial number of the product are located
on the back and on one side of the product. Record them
below in case you ever need service.
Model
Serial No.
*MFL718723272211REV01*
2
* Image shown may differ from your product.
Safety instructions
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Please read these safety precautions carefully before using the product.
• When lifting or moving the product, at least two people are
required due to the heavy weight of the product.
- The product may fall down, causing a malfunction or injury.
• Do not let children hang on or climb onto the product.
- The product may fall down, causing an injury or even death.
• Do not install the product in a place which is unstable or
vibrating or a place where the product is not completely
supported such as a shaky shelf or a tilted place.
- The product may fall down or overturn, causing an injury or
malfunction.
• Put the product on a flat and firm floor.
• When moving or handling a product assembled with the
Stand, be cautious about damaging the exterior of the product.
• When there is a stain or fingerprint left on the surface, wipe
it off gently.
- When removing a stain, do not use excessive force. Wiping
with excessive force may cause scratches or discoloration on
the product.
• Only use the authorized stand and wall mounting bracket
made specifically for LG products.
- Pursuant to Consumer Protection Law, LG Electronics will not
be held responsible for any product malfunction, material
damage or injury caused by using products not authorized
by LG Electronics.
Assembling and Preparing
Accessories
(M4 x L20)
How to Assemble the Stand
• When assembling the stand, put the product on a table or a
flat floor with its screen facing downward. Here, first put a soft
and fluffy cloth on the place, and then put the product on top
of it to prevent the screen from being damaged.
• When assembling the stand, ensure that all of the provided
screws are attached. If the screws are not fully tightened, the
product may tilt or tip over, resulting in damage. Tightening
the screws with excessive force may cause them to come off
due to abrasion of the screw joint.
• When assembling the product, do not use foreign substances
(oil, lubricant, etc.) on the screws.
- It may cause damage to the product.
• Before installing a wall mount support, disassemble the Stand
by conducting the method to assemble the stand in a reverse
order.
3
1-1
1-2
* If you have a TV packaging box, it is more convenient to mount the TV
as above and assemble it.
2
3
4
5
M4 x L20
6
4
7
1
4
8
9-1
9-2
9-3
* The figure is an example, and the user can freely arrange the lines.
5
Mounting on a Table
1 Lift and tilt the TV into its upright position on a table.
• Leave a 30cm (11.8inches) (minimum) space from the wall for
proper ventilation.
30cm
30cm
30cm
(11.8inches)
(11.8inches)
(11.8inches)
2 Connect the power cord to a wall outlet.
• If you install the TV on a stand, you need to take actions to
prevent the product from overturning. Otherwise, the product
may fall over, which may cause injury.
• Do not use any unapproved items to ensure the safety and
product life span.
• Any damage or injuries caused by using unapproved items are
not covered by the warranty.
• When installing on a cabinet or a shelf using a stand, make sure
its width is greater than that of the TV.
• If the TV is placed on the stand, its screen may be tilted back
slightly. If the stand is not level because an object is placed
under the stand or it is not on a flat surface, the product may fall
and cause injury or product damage.
Securing the TV to a Wall
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
• If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the flat surface.
• Use a platform or cabinet that is strong and large enough to support
the TV securely.
• Brackets, bolts and ropes are not provided. You can obtain additional
accessories from your local dealer.
Specifications
Model Name
Width x Depth x Height
(mm) (inches)
Weight
(kg) (lbs)
SQ-G2DT97
580 x 28 x 640
(22.8 x 1.1 x 25.1)
7
(15.4)
